Napravih kakto mi kazahte, opravih nqkoi ot problemite samo
ostana edna greshka, shte napisha pak Config-a zashtoto ima
malko promeni i shte napisha celiq log za da vididte dali
vsichko e OK :)) Thanks
Section "Module"
# This loads the DBE extension module.
Load "dbe" # Double buffer extension
# This loads the miscellaneous extensions module, and
disables
# initialisation of the XFree86-DGA extension within that
module.
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the
DGA extension
EndSubSection
# This loads the Type1 and FreeType font modules
Load "type1"
Load "freetype"
# This loads the GLX module
# Load "glx"
EndSection
#
**********************************************************************
# Files section. This allows default font and rgb paths to
be set
#
**********************************************************************
Section "Files"
# The location of the RGB database. Note, this is the name
of the
# file minus the extension (like ".txt" or ".db"). There is
normally
# no need to change the default.
RgbPath "/usr/X11R6/lib/X11/rgb"
# Multiple FontPath entries are allowed (which are
concatenated together),
# as well as specifying multiple comma-separated entries in
one FontPath
# command (or a combination of both methods)
#
# If you don't have a floating point coprocessor and emacs,
Mosaic or other
# programs take long to start up, try moving the Type1 and
Speedo directory
# to the end of this list (or comment them out).
#
FontPath "/usr/X11R6/lib/X11/fonts/local/"
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
# FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
# FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"
# The module search path. The default path is shown here.
# ModulePath "/usr/X11R6/lib/modules"
EndSection
#
**********************************************************************
# Server flags section.
#
**********************************************************************
Section "ServerFlags"
# Uncomment this to cause a core dump at the spot where a
signal is
# received. This may leave the console in an unusable
state, but may
# provide a better stack trace in the core dump to aid in
debugging
# Option "NoTrapSignals"
# Uncomment this to disable the <Crtl><Alt><BS> server abort
sequence
# This allows clients to receive this key event.
# Option "DontZap"
# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_->
mode switching
# sequences. This allows clients to receive these key
events.
# Option "Dont Zoom"
# Uncomment this to disable tuning with the xvidtune client.
With
# it the client can still run and fetch card and monitor
attributes,
# but it will not be allowed to change them. If it tries it
will
# receive a protocol error.
# Option "DisableVidModeExtension"
# Uncomment this to enable the use of a non-local xvidtune
client.
# Option "AllowNonLocalXvidtune"
# Uncomment this to disable dynamically modifying the input
device
# (mouse and keyboard) settings.
# Option "DisableModInDev"
# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only
xset).
# Option "AllowNonLocalModInDev"
EndSection
#
**********************************************************************
# Input devices
#
**********************************************************************
#
**********************************************************************
# Core keyboard's InputDevice section
#
**********************************************************************
Section "InputDevice"
Identifier "Keyboard1"
Driver "Keyboard"
# For most OSs the protocol can be omitted (it defaults to
"Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not
Solaris),
# uncomment the following line.
# Option "Protocol" "Xqueue"
Option "AutoRepeat" "500 30"
# Specify which keyboard LEDs can be user-controlled (eg,
with xset(1))
# Option "Xleds" "1 2 3"
# Option "LeftAlt" "Meta"
# Option "RightAlt" "ModeShift"
# To customise the XKB settings to suit your keyboard,
modify the
# lines below (which are the defaults). For example, for a
non-U.S.
# keyboard, you will probably want to use:
# Option "XkbModel" "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# Option "XkbModel" "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# Option "XkbLayout" "de"
# or:
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock
and
# control keys, use:
# Option "XkbOptions" "ctrl:swapcaps"
# These are the default XKB settings for XFree86
# Option "XkbRules" "xfree86"
# Option "XkbModel" "pc101"
# Option "XkbLayout" "us"
# Option "XkbVariant" ""
# Option "XkbOptions" ""
# Option "XkbDisable"
Option "XkbRules" "xfree86"
Option "XkbModel" "pc101"
Option "XkbLayout" "us"
Option "XkbCompat" ""
EndSection
#
**********************************************************************
# Core Pointer's InputDevice section
#
**********************************************************************
Section "InputDevice"
# Identifier and driver
Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "Logitech"
Option "Device" "/dev/mouse"
# When using XQUEUE, comment out the above two lines, and
uncomment
# the following line.
# Option "Protocol" "Xqueue"
# Baudrate and SampleRate are only for some Logitech mice.
In
# almost every case these lines should be omitted.
# Option "BaudRate" "9600"
# Option "SampleRate" "150"
# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is
50ms)
Option "Emulate3Buttons"
# Option "Emulate3Timeout" "50"
# ChordMiddle is an option for some 3-button Logitech mice
# Option "ChordMiddle"
EndSection
#
**********************************************************************
# Other input device sections
# this is optional and is required only if you
# are using extended input devices. This is for example
only. Refer
# to the XF86Config man page for a description of the
options.
#
**********************************************************************
#
# Section "InputDevice"
# Identifier "Mouse2"
# Driver "mouse"
# Option "Protocol" "MouseMan"
# Option "Device" "/dev/mouse2"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball"
# Driver "magellan"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball2"
# Driver "spaceorb"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen0"
# Driver "microtouch"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "1412"
# Option "MaxX" "15184"
# Option "MinY" "15372"
# Option "MaxY" "1230"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen1"
# Driver "elo2300"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "231"
# Option "MaxX" "3868"
# Option "MinY" "3858"
# Option "MaxY" "272"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonThreshold" "17"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection
#
**********************************************************************
# Monitor section
#
**********************************************************************
# Any number of monitor sections may be present
Section "Monitor"
Identifier "S/T 77E/76E"
# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete
values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR
MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
HorizSync 30-70
# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync
frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync
frequencies
# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete
values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR
MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
VertRefresh 50-160
EndSection
#
**********************************************************************
# Graphics device section
#
**********************************************************************
# Any number of graphics device sections may be present
# Standard VGA Device:
Section "Device"
Identifier "Standard VGA"
VendorName "Unknown"
BoardName "Unknown"
# The chipset line is optional in most cases. It can be
used to override
# the driver's chipset detection, and should not normally be
specified.
# Chipset "generic"
# The Driver line must be present. When using run-time
loadable driver
# modules, this line instructs the server to load the
specified driver
# module. Even when not using loadable driver modules, this
line
# indicates which driver should interpret the information in
this section.
Driver "vga"
# The BusID line is used to specify which of possibly
multiple devices
# this section is intended for. When this line isn't
present, a device
# section can only match up with the primary video device.
For PCI
# devices a line like the following could be used. This
line should not
# normally be included unless there is more than one video
device
# intalled.
# BusID "PCI:0:10:0"
# VideoRam 256
# Clocks 25.2 28.3
EndSection
# Device configured by xf86config:
Section "Device"
Identifier "nVidia Corporation|NV11 DDR"
Driver "nv"
#VideoRam 32768
# Insert Clocks lines here if appropriate
EndSection
#
**********************************************************************
# Screen sections
#
**********************************************************************
# Any number of screen sections may be present. Each
describes
# the configuration of a single screen. A single specific
screen section
# may be specified from the X server command line with the
"-screen"
# option.
Section "Screen"
Identifier "Screen 1"
Device "nVidia Corporation|NV11 DDR"
Monitor "S/T 77E/76E"
DefaultDepth 16
Subsection "Display"
Depth 8
Modes "640x480" "800x600" "1024x768"
"1280x1024"
ViewPort 0 0
Virtual 1600 1280
EndSubsection
Subsection "Display"
Depth 16
Modes "800x600"
ViewPort 0 0
Virtual 1280 1024
EndSubsection
Subsection "Display"
Depth 24
Modes "640x480" "800x600" "1024x768"
"1280x1024"
ViewPort 0 0
Virtual 1152 900
EndSubsection
EndSection
#
**********************************************************************
# ServerLayout sections.
#
**********************************************************************
# Any number of ServerLayout sections may be present. Each
describes
# the way multiple screens are organised. A specific
ServerLayout
# section may be specified from the X server command line
with the
# "-layout" option. In the absence of this, the first
section is used.
# When now ServerLayout section is present, the first Screen
section
# is used alone.
Section "ServerLayout"
# The Identifier line must be present
Identifier "Simple Layout"
# Each Screen line specifies a Screen section name, and
optionally
# the relative position of other screens. The four names
after
# primary screen name are the screens to the top, bottom,
left and right
# of the primary screen. In this example, screen 2 is
located to the
# right of screen 1.
Screen "Screen 1"
# Each InputDevice line specifies an InputDevice section
name and
# optionally some options to specify the way the device is
to be
# used. Those options include "CorePointer", "CoreKeyboard"
and
# "SendCoreEvents".
InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"
EndSection
---------------------------------------------
Eto i log-a ....
XFree86 Version 4.0.1a / X Window System
(protocol Version 11, revision 0, vendor release 6400)
Release Date: 2 August 2000
If the server is older than 6-12 months, or if your card is
newer
than the above date, look for a newer version before
reporting
problems. (see http://www.XFree86.Org/FAQ)
Operating System: Linux 2.2.5-22smp i686 [ELF]
Module Loader present
(==) Log file: "/var/log/XFree86.0.log", Time: Wed Jul 31
04:17:11 2002
(++) Using config file: "/etc/X11/XF86Config"
Markers: (--) probed, (**) from config file, (==) default
setting,
(++) from command line, (!!) notice, (II)
informational,
(WW) warning, (EE) error, (??) unknown.
(==) ServerLayout "Simple Layout"
(**) |-->Screen "Screen 1" (0)
(**) | |-->Monitor "S/T 77E/76E"
(**) | |-->Device "nVidia Corporation|NV11 DDR"
(**) |-->Input Device "Mouse1"
(**) |-->Input Device "Keyboard1"
(**) Option "AutoRepeat" "500 30"
(WW) Option "XkbCompat" requires an string value
(**) Option "XkbRules" "xfree86"
(**) XKB: rules: "xfree86"
(**) Option "XkbModel" "pc101"
(**) XKB: model: "pc101"
(**) Option "XkbLayout" "us"
(**) XKB: layout: "us"
(**) FontPath set to
"/usr/X11R6/lib/X11/fonts/local/,/usr/X11R6/lib/X11/fonts/misc/,/usr/X11R6/lib/X11/fonts/75dpi/:unscaled,/usr/X11R6/lib/X11/fonts/Type1/,/usr/X11R6/lib/X11/fonts/Speedo/,/usr/X11R6/lib/X11/fonts/75dpi/"
(**) RgbPath set to "/usr/X11R6/lib/X11/rgb"
(==) ModulePath set to "/usr/X11R6/lib/modules"
(--) using VT number 13
(II) Module ABI versions:
XFree86 ANSI C Emulation: 0.1
XFree86 Video Driver: 0.2
XFree86 XInput driver : 0.1
XFree86 Server Extension : 0.1
XFree86 Font Renderer : 0.1
(II) Loader running on linux
(II) LoadModule: "bitmap"
(II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a
(II) Module bitmap: vendor="The XFree86 Project"
compiled for 4.0.1a, module version = 1.0.0
Module class: XFree86 Font Renderer
ABI class: XFree86 Font Renderer, version 0.1
(II) Loading font Bitmap
(II) LoadModule: "pcidata"
(II) Loading /usr/X11R6/lib/modules/libpcidata.a
(II) Module pcidata: vendor="The XFree86 Project"
compiled for 4.0.1a, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.2
(II) PCI: Probing config type using method 1
(II) PCI: Config type is 1
(II) PCI: stages = 0x03, oldVal1 = 0x00000000, mode1Res1 =
0x80000000
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 1106,0305 card 1019,0987 rev 03
class 06,00,00 hdr 00
(II) PCI: 00:01:0: chip 1106,8305 card 0000,0000 rev 00
class 06,04,00 hdr 01
(II) PCI: 00:07:0: chip 1106,0686 card 1106,0000 rev 40
class 06,01,00 hdr 80
(II) PCI: 00:07:1: chip 1106,0571 card 1106,0571 rev 06
class 01,01,8a hdr 00
(II) PCI: 00:07:2: chip 1106,3038 card 0925,1234 rev 16
class 0c,03,00 hdr 00
(II) PCI: 00:07:4: chip 1106,3057 card 1019,0987 rev 40
class 06,00,00 hdr 00
(II) PCI: 00:07:5: chip 1106,3058 card 1019,0987 rev 50
class 04,01,00 hdr 00
(II) PCI: 01:00:0: chip 10de,0111 card 0000,0000 rev b2
class 03,00,00 hdr 00
(II) PCI: End of PCI scan
(II) LoadModule: "scanpci"
(II) Loading /usr/X11R6/lib/modules/libscanpci.a
(II) Module scanpci: vendor="The XFree86 Project"
compiled for 4.0.1a, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.2
(II) UnloadModule: "scanpci"
(II) Unloading /usr/X11R6/lib/modules/libscanpci.a
(II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x0c
(VGA_EN is set)
(II) Bus 1 I/O range:
(II) Bus 1 non-prefetchable memory range:
[0] -1 0xe0000000 - 0xe1ffffff (0x2000000) MX[B]
(II) Bus 1 prefetchable memory range:
[0] -1 0xd8000000 - 0xdfffffff (0x8000000) MX[B]
(--) PCI:*(1:0:0) NVidia unknown chipset (0x0111) rev 178,
Mem @ 0xe0000000/24, 0xd8000000/27
(II) Addressable bus resource ranges are
[0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
[1] -1 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) OS-reported resource ranges:
[0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0x00000000 - 0x000001ff (0x200) IX[B]E
(II) Active PCI resource ranges:
[0] -1 0xd0000000 - 0xd7ffffff (0x8000000) MX[B]E
[1] -1 0xd8000000 - 0xdfffffff (0x8000000) MX[B](B)
[2] -1 0xe0000000 - 0xe0ffffff (0x1000000) MX[B](B)
[3] -1 0x0000e400 - 0x0000e4ff (0x100) IX[B]E
[4] -1 0x0000e000 - 0x0000e0ff (0x100) IX[B]E
[5] -1 0x0000dc00 - 0x0000dcff (0x100) IX[B]E
[6] -1 0x0000d400 - 0x0000d4ff (0x100) IX[B]E
[7] -1 0x0000d000 - 0x0000d0ff (0x100) IX[B]E
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0xd0000000 - 0xd7ffffff (0x8000000) MX[B]E
[1] -1 0xd8000000 - 0xdfffffff (0x8000000) MX[B](B)
[2] -1 0xe0000000 - 0xe0ffffff (0x1000000) MX[B](B)
[3] -1 0x0000e400 - 0x0000e4ff (0x100) IX[B]E
[4] -1 0x0000e000 - 0x0000e0ff (0x100) IX[B]E
[5] -1 0x0000dc00 - 0x0000dcff (0x100) IX[B]E
[6] -1 0x0000d400 - 0x0000d4ff (0x100) IX[B]E
[7] -1 0x0000d000 - 0x0000d0ff (0x100) IX[B]E
(II) OS-reported resource ranges after removing overlaps
with PCI:
[0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0x00000000 - 0x000001ff (0x200) IX[B]E
(II) All system resource ranges:
[0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0xd0000000 - 0xd7ffffff (0x8000000) MX[B]E
[6] -1 0xd8000000 - 0xdfffffff (0x8000000) MX[B](B)
[7] -1 0xe0000000 - 0xe0ffffff (0x1000000) MX[B](B)
[8] -1 0x00000000 - 0x000001ff (0x200) IX[B]E
[9] -1 0x0000e400 - 0x0000e4ff (0x100) IX[B]E
[10] -1 0x0000e000 - 0x0000e0ff (0x100) IX[B]E
[11] -1 0x0000dc00 - 0x0000dcff (0x100) IX[B]E
[12] -1 0x0000d400 - 0x0000d4ff (0x100) IX[B]E
[13] -1 0x0000d000 - 0x0000d0ff (0x100) IX[B]E
(II) LoadModule: "dbe"
(II) Loading /usr/X11R6/lib/modules/extensions/libdbe.a
(II) Module dbe: vendor="The XFree86 Project"
compiled for 4.0.1a, module version = 1.0.0
Module class: XFree86 Server Extension
ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "extmod"
(II) Loading /usr/X11R6/lib/modules/extensions/libextmod.a
(II) Module extmod: vendor="The XFree86 Project"
compiled for 4.0.1a, module version = 1.0.0
Module class: XFree86 Server Extension
ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension DPMS
(II) Loading extension FontCache
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) LoadModule: "type1"
(II) Loading /usr/X11R6/lib/modules/fonts/libtype1.a
(II) Module type1: vendor="The XFree86 Project"
compiled for 4.0.1a, module version = 1.0.0
Module class: XFree86 Font Renderer
ABI class: XFree86 Font Renderer, version 0.1
(II) Loading font Type1
(II) Loading font CID
(II) LoadModule: "freetype"
(II) Loading /usr/X11R6/lib/modules/fonts/libfreetype.a
(II) Module freetype: vendor="The XFree86 Project"
compiled for 4.0.1a, module version = 1.1.7
Module class: XFree86 Font Renderer
ABI class: XFree86 Font Renderer, version 0.1
(II) Loading font FreeType
(II) LoadModule: "nv"
(II) Loading /usr/X11R6/lib/modules/drivers/nv_drv.o
(II) Module nv: vendor="The XFree86 Project"
compiled for 4.0.1a, module version = 1.0.0
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.2
(II) LoadModule: "mouse"
(II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o
(II) Module mouse: vendor="The XFree86 Project"
compiled for 4.0.1a, module version = 1.0.0
Module class: XFree86 XInput Driver
ABI class: XFree86 XInput driver, version 0.1
(II) NV: driver for NVIDIA chipsets: RIVA128, RIVATNT,
RIVATNT2,
RIVATNT2 (Ultra), RIVATNT2 (Vanta), RIVATNT2 M64,
RIVATNT2 (Integrated), GeForce 256, GeForce DDR, Quadro,
GeForce 2
(II) Primary Device is: PCI 01:00:0
(EE) No devices detected.
Fatal server error:
no screens found
|
