Zdr fenove imam sledniqt vaprs kam vas 
 povzvam Seagate Model=ST31722A hdd za da si digna malko po
 obektivni prochini ,disk pronstranstvo s 1.7G koeto palno me
ustroiva za sega , no se nataknah na edin stranen problem .
HDD e zakacheno kato single secondary master device ,
 naprqavil sam mu fs ot 1 do 3303 cilinder na type
 83,formairal sam go na ext3 i sam go montiral kato hdparm
 dava do kolkoto se ima v oredvid sarakteristikite na hdd
 dobri resultati , do tuk vsichko e tok , no pri iskane na
info ot hdparm za hdd gledayte  kvo stava : 
[root@desktop1 kiril(.615 Mb)]$ /sbin/hdparm -i /dev/hdc

/dev/hdc:

 Model=ST31722A, FwRev=0.42, SerialNo=XJE56319
  Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs
RotSpdTol>.5% }
 RawCHS=3303/16/63, TrkSize=0, SectSize=0, ECCbytes=4
  BuffType=unknown, BuffSize=128kB, MaxMultSect=16,
MultSect=16
  CurCHS=3303/16/63, CurSects=3329424, LBA=yes,
LBAsects=3329424
  IORDY=on/off, tPIO={min:383,w/IORDY:120},
tDMA={min:120,rec:120}
 PIO modes: pio0 pio1 pio3 pio4
 DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2
 AdvancedPM=no
Segmentation fault

Ops Segmentation fault : 
 Tuk po princhip trebva da mi izkara WriteCache i sled tova
Drive Supports no uvi nestava .
Sreshtal li e nqkoi takav problem ?
 Zadavam go kato vapros zashtoto vapreki che si raboti i nqma
 problem po nego da se piche,trie i t.n pro otmontirvane i po
tochno predi flush na ide device mashinata zabiva totalno.
Drugoto koeto me pretesnqva e dmesg skivaite kvo mi dava :

hda: ST36424A, ATA DISK drive
hdc: ST31722A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
blk: queue c035e6a4, I/O limit 4095Mb (mask 0xffffffff)
 hda: 12594960 sectors (6449 MB) w/512KiB Cache,
CHS=833/240/63, UDMA(33)
blk: queue c035ea08, I/O limit 4095Mb (mask 0xffffffff)
 hdc: 3329424 sectors (1705 MB) w/128KiB Cache,
CHS=3303/16/63, UDMA(33)
ide-floppy driver 0.99.newide
Partition check:
 hda: hda1 hda2 hda3
 hdc: [PTBL] [825/64/63] hdc1

  tva [PTBL] moje li da go obqsni nqkoi kvo e?

Journalled Block Device driver loaded
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 280k freed
Adding Swap: 196552k swap-space (priority -1)
 EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,2), internal
journal
kjournald starting.  Commit interval 5 seconds
 EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide1(22,1), internal
journal
EXT3-fs: mounted filesystem with ordered data mode.

Mountva i vsichko e tok.

Oko moje nqkoi da udari edno rano ??
10X predvaritelno

Hi,
 chesno kazano ne sum sreshtal takowa neshto do sega. no wse
 pak towa ne mi prechi da se opitam da te nasocha i da ti dam
 nqkoi suwet. Znachi spored men moje da se okaje che problema
 e w support-a na chipset-a na motherboard-a t.e. iskam da mi
pastenesh slednite results:
hdparm /dev/hdc 
lspci -vv |grep IDE
 tva kato za nachalo :) posle shte mu mislim. Ideqta mi e che
 moje da nqmash ili da si si orqzal supoprt-a za toq chipset
:)) (kakto az bqh naprawil predi dosta wreme:))

best regards,
dido

dido 10x za help
eto i resultatite : 
[root@desktop1 kiril(.615 Mb)]$ /sbin/hdparm /dev/hdc

/dev/hdc:
 multcount    = 16 (on)
 I/O support  =  0 (default 16-bit)
 unmaskirq    =  0 (off)
 using_dma    =  1 (on)
 keepsettings =  0 (off)
 nowerr       =  0 (off)
 readonly     =  0 (off)
 readahead    =  8 (on)
 geometry     = 825/64/63, sectors = 3329424, start = 0
 busstate     =  1 (on)

[root@desktop1 kiril(.615 Mb)]$ /sbin/lspci -vv |grep IDE
 00:04.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE
(rev 01) (prog-if 80 [Master])

Eto ti i info za IDE:

 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
(prog-if 80 [Master])
         Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
         Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32
        Region 4: I/O ports at d800 [size=16]

Hm ,
q mi kaji s kakva distribucia si i kakuv kernel polzwash,
sushto taka mi paste towa:
cat /usr/src/linux*/.config | grep CONFIG_BLK_DEV_PIIX

BR,
Dido..

RH 7.3 kernel-2.4.18-3 

 [root@desktop1 kiril(.615 Mb)]$ cat
 /usr/src/linux-2.4/configs/kernel-2.4.18-i386.config | grep
CONFIG_BLK_DEV_PIIX
CONFIG_BLK_DEV_PIIX=y
[root@desktop1 kiril(.615 Mb)]$


 [root@desktop1 kiril(.615 Mb)]$ cat
 /usr/src/linux-2.4/configs/kernel-2.4.18-i686.config | grep
CONFIG_BLK_DEV_PIIX
CONFIG_BLK_DEV_PIIX=y
[root@desktop1 kiril(.615 Mb)]$

 [root@desktop1 kiril(.615 Mb)]$ cat
 /usr/src/linux-2.4.18-3/configs/kernel-2.4.18-i386.config |
grep CONFIG_BLK_DEV_PIIX
CONFIG_BLK_DEV_PIIX=y
[root@desktop1 kiril(.615 Mb)]$

 [root@desktop1 kiril(.615 Mb)]$ cat
 /usr/src/linux-2.4.18-3/configs/kernel-2.4.18-i686.config |
grep CONFIG_BLK_DEV_PIIX
CONFIG_BLK_DEV_PIIX=y

probvai da pusnesh 32 bitov transfer:
hdparm -c 1 /dev/hdc