[Цитат]

Цитат (Ivaylo78 @ Авг. 07 2007,10:49)

Cat,получи се както каза, но изчезна знаменцата долу вдясно. '> Но май така е по добре. Благодаря за помощта на всички. А и научих някой работи покрай тази задачка.     '>

Я постни ,моля те съдържанието на целия фай,че аз махнах отметката но не става при мен!

рестартираш ли след махането на отметката?

[Цитат]

Цитат

aladin@sabayonx86 ~ $ su Password: sabayonx86 aladin # ifconfig eth0      Link encap:Ethernet  HWaddr 00:15:F2:A1:59:57           inet addr:10.100.46.82  Bcast:10.100.255.255  Mask:255.255.0.0           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1           RX packets:24 errors:0 dropped:0 overruns:0 frame:0           TX packets:35 errors:0 dropped:0 overruns:0 carrier:0           collisions:0 txqueuelen:1000           RX bytes:1484 (1.4 Kb)  TX bytes:7152 (6.9 Kb)           Interrupt:18 Base address:0x6000 lo        Link encap:Local Loopback           inet addr:127.0.0.1  Mask:255.0.0.0           UP LOOPBACK RUNNING  MTU:16436  Metric:1           RX packets:110 errors:0 dropped:0 overruns:0 frame:0           TX packets:110 errors:0 dropped:0 overruns:0 carrier:0           collisions:0 txqueuelen:0           RX bytes:8276 (8.0 Kb)  TX bytes:8276 (8.0 Kb) sabayonx86 aladin # route Kernel IP routing table Destination     Gateway         Genmask         Flags Metric Ref    Use Iface 10.100.0.0      *               255.255.0.0     U     0      0        0 eth0 loopback        *               255.0.0.0       U     0      0        0 lo sabayonx86 aladin # tail -n 200 /var/messages tail: РЅРµ може РґР° СЃРµ отвори „/var/messages“ Р·Р° четене: No such file or directory sabayonx86 aladin # tail -n 200 /var/log/messages Aug  7 01:01:14 sabayonx86 [   32.035114] Device driver usbdev3.1_ep00 lacks bus  and class support for being resumed. Aug  7 01:01:14 sabayonx86 [   32.035121] usb usb3: configuration #1 chosen from  1 choice Aug  7 01:01:14 sabayonx86 [   32.035223] hub 3-0:1.0: USB hub found Aug  7 01:01:14 sabayonx86 [   32.035232] hub 3-0:1.0: 4 ports detected Aug  7 01:01:14 sabayonx86 [   32.135804] Device driver usbdev3.1_ep81 lacks bus  and class support for being resumed. Aug  7 01:01:14 sabayonx86 [   32.396221] usb 3-4: new full speed USB device usi ng ohci_hcd and address 2 Aug  7 01:01:14 sabayonx86 [   32.587037] Device driver usbdev3.2_ep00 lacks bus  and class support for being resumed. Aug  7 01:01:14 sabayonx86 [   32.587045] usb 3-4: configuration #1 chosen from 1 choice Aug  7 01:01:14 sabayonx86 [   32.590035] Device driver usbdev3.2_ep81 lacks bus  and class support for being resumed. Aug  7 01:01:14 sabayonx86 [   32.590052] Device driver usbdev3.2_ep82 lacks bus  and class support for being resumed. Aug  7 01:01:14 sabayonx86 [   32.590069] Device driver usbdev3.2_ep02 lacks bus  and class support for being resumed. Aug  7 01:01:14 sabayonx86 [   32.590107] Device driver usbdev3.2_ep83 lacks bus  and class support for being resumed. Aug  7 01:01:14 sabayonx86 [   32.590125] Device driver usbdev3.2_ep03 lacks bus  and class support for being resumed. Aug  7 01:01:14 sabayonx86 [   32.896646] Bluetooth: Core ver 2.11 Aug  7 01:01:14 sabayonx86 [   32.896698] NET: Registered protocol family 31 Aug  7 01:01:14 sabayonx86 [   32.896700] Bluetooth: HCI device and connection m anager initialized Aug  7 01:01:14 sabayonx86 [   32.896703] Bluetooth: HCI socket layer initialize d Aug  7 01:01:14 sabayonx86 [   32.898205] Bluetooth: HCI USB driver ver 2.9 Aug  7 01:01:14 sabayonx86 [   32.900832] Device driver usbdev3.2_ep83 lacks bus  and class support for being resumed. Aug  7 01:01:14 sabayonx86 [   32.900935] Device driver usbdev3.2_ep03 lacks bus  and class support for being resumed. Aug  7 01:01:14 sabayonx86 [   32.901048] Device driver hci0 lacks bus and class  support for being resumed. Aug  7 01:01:14 sabayonx86 [   32.901067] usbcore: registered new interface driv er hci_usb Aug  7 01:01:14 sabayonx86 [   33.872336] EXT3 FS on sdb5, internal journal Aug  7 01:01:14 sabayonx86 [   34.097005] vboxdrv: Trying to deactivate NMI watc hdog permanently... Aug  7 01:01:14 sabayonx86 [   34.097008] vboxdrv: Successfully done. Aug  7 01:01:14 sabayonx86 [   41.893455] Bluetooth: L2CAP ver 2.8 Aug  7 01:01:14 sabayonx86 [   41.893457] Bluetooth: L2CAP socket layer initiali zed Aug  7 01:01:14 sabayonx86 [   42.052784] Bluetooth: RFCOMM socket layer initial ized Aug  7 01:01:14 sabayonx86 [   42.052794] Bluetooth: RFCOMM TTY layer initialize d Aug  7 01:01:14 sabayonx86 [   42.052796] Bluetooth: RFCOMM ver 1.8 Aug  7 01:01:18 sabayonx86 rpc.statd[7516]: Version 1.0.11 Starting Aug  7 01:01:18 sabayonx86 rpc.statd[7516]: gethostbyname error for sabayonx86 Aug  7 01:01:18 sabayonx86 hpiod: 1.6.10 accepting connections at 2208... Aug  7 01:01:21 sabayonx86 [   57.542550] NFSD: Using /var/lib/nfs/v4recovery as  the NFSv4 state recovery directory Aug  7 01:01:21 sabayonx86 [   57.549182] NFSD: starting 90-second grace period Aug  7 01:01:22 sabayonx86 [   58.413538] fbsplash: console 1 using theme 'sabay on' Aug  7 01:01:22 sabayonx86 [   58.422981] fbsplash: switched splash state to 'on ' on console 1 Aug  7 01:01:22 sabayonx86 [   58.442428] fbsplash: console 2 using theme 'sabay on' Aug  7 01:01:22 sabayonx86 [   58.447699] fbsplash: switched splash state to 'on ' on console 2 Aug  7 01:01:22 sabayonx86 [   58.464432] fbsplash: console 3 using theme 'sabay on' Aug  7 01:01:22 sabayonx86 [   58.471825] fbsplash: switched splash state to 'on ' on console 3 Aug  7 01:01:22 sabayonx86 [   58.487707] fbsplash: console 4 using theme 'sabay on' Aug  7 01:01:22 sabayonx86 [   58.496161] fbsplash: switched splash state to 'on ' on console 4 Aug  7 01:01:22 sabayonx86 [   58.512653] fbsplash: console 5 using theme 'sabay on' Aug  7 01:01:22 sabayonx86 [   58.521197] fbsplash: switched splash state to 'on ' on console 5 Aug  7 01:01:22 sabayonx86 [   58.530607] fbsplash: console 11 using theme 'saba yon' Aug  7 01:01:22 sabayonx86 [   58.535773] fbsplash: switched splash state to 'on ' on console 11 Aug  7 01:01:24 sabayonx86 [   61.062430] ACPI: PCI Interrupt Link [LNKE] enable d at IRQ 18 Aug  7 01:01:24 sabayonx86 [   61.062441] ACPI: PCI Interrupt 0000:01:00.0[A] ->  Link [LNKE] -> GSI 18 (level, low) -> IRQ 20 Aug  7 01:01:25 sabayonx86 [   62.357163] [fglrx] Internal AGP support requested , but kernel AGP support active. Aug  7 01:01:25 sabayonx86 [   62.357169] [fglrx] Have to use kernel AGP support  to avoid conflicts. Aug  7 01:01:25 sabayonx86 [   62.357173] [fglrx] AGP detected, AgpState   = 0x1 f00421b (hardware caps of chipset) Aug  7 01:01:25 sabayonx86 [   62.357408] agpgart: Found an AGP 3.0 compliant de vice at 0000:00:00.0. Aug  7 01:01:25 sabayonx86 [   62.357424] agpgart: Putting AGP V3 device at 0000 :00:00.0 into 8x mode Aug  7 01:01:25 sabayonx86 [   62.357446] agpgart: Putting AGP V3 device at 0000 :01:00.0 into 8x mode Aug  7 01:01:25 sabayonx86 [   62.357461] [fglrx] AGP enabled,  AgpCommand = 0x1 f004312 (selected caps) Aug  7 01:01:25 sabayonx86 [   62.362931] [fglrx] total      GART = 268435456 Aug  7 01:01:25 sabayonx86 [   62.362939] [fglrx] free       GART = 252440576 Aug  7 01:01:25 sabayonx86 [   62.362941] [fglrx] max single GART = 252440576 Aug  7 01:01:25 sabayonx86 [   62.362943] [fglrx] total      LFB  = 134217728 Aug  7 01:01:25 sabayonx86 [   62.362946] [fglrx] free       LFB  = 90165248 Aug  7 01:01:25 sabayonx86 [   62.362948] [fglrx] max single LFB  = 90165248 Aug  7 01:01:25 sabayonx86 [   62.362950] [fglrx] total      Inv  = 0 Aug  7 01:01:25 sabayonx86 [   62.362951] [fglrx] free       Inv  = 0 Aug  7 01:01:25 sabayonx86 [   62.362953] [fglrx] max single Inv  = 0 Aug  7 01:01:25 sabayonx86 [   62.362955] [fglrx] total      TIM  = 0 Aug  7 01:01:27 sabayonx86 avahi-daemon[8414]: Found user 'avahi' (UID 110) and group 'avahi' (GID 445). Aug  7 01:01:27 sabayonx86 avahi-daemon[8414]: Successfully dropped root privile ges. Aug  7 01:01:27 sabayonx86 avahi-daemon[8414]: avahi-daemon 0.6.18 starting up. Aug  7 01:01:27 sabayonx86 avahi-daemon[8414]: Successfully called chroot(). Aug  7 01:01:27 sabayonx86 avahi-daemon[8414]: Successfully dropped remaining ca pabilities. Aug  7 01:01:27 sabayonx86 avahi-daemon[8414]: Loading service file /services/sf tp-ssh.service. Aug  7 01:01:27 sabayonx86 avahi-daemon[8414]: Loading service file /services/ss h.service. Aug  7 01:01:27 sabayonx86 avahi-daemon[8414]: Network interface enumeration com pleted. Aug  7 01:01:27 sabayonx86 avahi-daemon[8414]: Registering HINFO record with val ues 'I686'/'LINUX'. Aug  7 01:01:27 sabayonx86 avahi-daemon[8414]: Server startup complete. Host nam e is sabayonx86.local. Local service cookie is 25218812. Aug  7 01:01:27 sabayonx86 avahi-daemon[8414]: Service "sabayonx86" (/services/s sh.service) successfully established. Aug  7 01:01:27 sabayonx86 avahi-daemon[8414]: Service "SFTP File Transfer on sa bayonx86" (/services/sftp-ssh.service) successfully established. Aug  7 01:01:27 sabayonx86 dhcdbd: Started up. Aug  7 01:01:28 sabayonx86 NetworkManager: <info>  starting... Aug  7 01:01:28 sabayonx86 NetworkManager: <info>  New VPN service 'vpnc' (org.f reedesktop.NetworkManager.vpnc). Aug  7 01:01:28 sabayonx86 NetworkManager: <info>  New VPN service 'openvpn' (or g.freedesktop.NetworkManager.openvpn). Aug  7 01:01:28 sabayonx86 NetworkManager: <info>  You are using a deprecated co nfiguration syntax for eth0. Aug  7 01:01:28 sabayonx86 NetworkManager: <info>  You are advised to read /etc/ conf.d/net.example and upgrade it accordingly. Aug  7 01:01:28 sabayonx86 NetworkManager: <debug> [1186448488.753515] GentooRea dConfig(): Found config_eth0 in /etc/conf.d/net. Aug  7 01:01:28 sabayonx86 NetworkManager: <debug> [1186448488.753658] GentooRea dConfig(): Found hostname. Aug  7 01:01:28 sabayonx86 NetworkManager: nm_ip4_config_set_hostname: assertion  `config != NULL' failed Aug  7 01:01:28 sabayonx86 NetworkManager: <info>  Network configuration for dev ice 'eth0' does not specify a gateway but is statically configured (non-DHCP). Aug  7 01:01:28 sabayonx86 NetworkManager: <info>  eth0: Device is fully-support ed using driver 'forcedeth'. Aug  7 01:01:28 sabayonx86 NetworkManager: <info>  nm_device_init(): waiting for  device's worker thread to start Aug  7 01:01:28 sabayonx86 NetworkManager: <info>  nm_device_init(): device's wo rker thread started, continuing. Aug  7 01:01:28 sabayonx86 NetworkManager: <info>  Now managing wired Ethernet ( 802.3) device 'eth0'. Aug  7 01:01:28 sabayonx86 NetworkManager: <info>  Deactivating device eth0. Aug  7 01:01:29 sabayonx86 NetworkManager: <info>  Will activate wired connectio n 'eth0' because it now has a link. Aug  7 01:01:29 sabayonx86 NetworkManager: <info>  SWITCH: no current connection , found better connection 'eth0'. Aug  7 01:01:29 sabayonx86 dhcdbd: message_handler: message handler not found un der /com/redhat/dhcp/eth0 for sub-path eth0.dbus.get.reason Aug  7 01:01:29 sabayonx86 NetworkManager: <info>  Will activate connection 'eth 0'. Aug  7 01:01:29 sabayonx86 NetworkManager: <info>  Device eth0 activation schedu led... Aug  7 01:01:29 sabayonx86 NetworkManager: <info>  Activation (eth0) started... Aug  7 01:01:29 sabayonx86 NetworkManager: <info>  Activation (eth0) Stage 1 of 5 (Device Prepare) scheduled... Aug  7 01:01:29 sabayonx86 NetworkManager: <info>  Activation (eth0) Stage 1 of 5 (Device Prepare) started... Aug  7 01:01:29 sabayonx86 NetworkManager: <info>  Activation (eth0) Stage 2 of 5 (Device Configure) scheduled... Aug  7 01:01:29 sabayonx86 NetworkManager: <info>  Activation (eth0) Stage 1 of 5 (Device Prepare) complete. Aug  7 01:01:29 sabayonx86 NetworkManager: <info>  Activation (eth0) Stage 2 of 5 (Device Configure) starting... Aug  7 01:01:29 sabayonx86 NetworkManager: <info>  Activation (eth0) Stage 2 of 5 (Device Configure) successful. Aug  7 01:01:29 sabayonx86 NetworkManager: <info>  Activation (eth0) Stage 3 of 5 (IP Configure Start) scheduled. Aug  7 01:01:29 sabayonx86 NetworkManager: <info>  Activation (eth0) Stage 2 of 5 (Device Configure) complete. Aug  7 01:01:29 sabayonx86 NetworkManager: <info>  Activation (eth0) Stage 3 of 5 (IP Configure Start) started... Aug  7 01:01:29 sabayonx86 NetworkManager: <info>  Activation (eth0) Stage 4 of 5 (IP Configure Get) scheduled... Aug  7 01:01:29 sabayonx86 NetworkManager: <info>  Activation (eth0) Stage 3 of 5 (IP Configure Start) complete. Aug  7 01:01:29 sabayonx86 NetworkManager: <info>  Activation (eth0) Stage 4 of 5 (IP Configure Get) started... Aug  7 01:01:29 sabayonx86 NetworkManager: <info>  Activation (eth0) Stage 5 of 5 (IP Configure Commit) scheduled... Aug  7 01:01:29 sabayonx86 NetworkManager: <info>  Activation (eth0) Stage 4 of 5 (IP Configure Get) complete. Aug  7 01:01:29 sabayonx86 NetworkManager: <info>  Activation (eth0) Stage 5 of 5 (IP Configure Commit) started... Aug  7 01:01:29 sabayonx86 avahi-daemon[8414]: Joining mDNS multicast group on i nterface eth0.IPv4 with address 10.100.46.82. Aug  7 01:01:29 sabayonx86 avahi-daemon[8414]: New relevant interface eth0.IPv4 for mDNS. Aug  7 01:01:29 sabayonx86 avahi-daemon[8414]: Registering new address record fo r 10.100.46.82 on eth0.IPv4. Aug  7 01:01:30 sabayonx86 NetworkManager: <info>  Activation (eth0) Finish hand ler scheduled. Aug  7 01:01:30 sabayonx86 NetworkManager: <info>  Activation (eth0) Stage 5 of 5 (IP Configure Commit) complete. Aug  7 01:01:30 sabayonx86 NetworkManager: <info>  Activation (eth0) successful,  device activated. Aug  7 01:01:31 sabayonx86 sshd[8867]: Server listening on 0.0.0.0 port 22. Aug  7 01:01:31 sabayonx86 cron[8951]: (CRON) STARTUP (V5.0) Aug  7 01:01:33 sabayonx86 [   69.636442] atkbd.c: Spurious ACK on isa0060/serio 0. Some program might be trying access hardware directly. Aug  7 01:01:34 sabayonx86 [   70.635449] atkbd.c: Spurious ACK on isa0060/serio 0. Some program might be trying access hardware directly. Aug  7 01:01:40 sabayonx86 kdm_greet[8766]: Internal error: memory corruption de tected Aug  7 01:01:40 sabayonx86 kdm: :0[8199]: pam_unix(kde:session): session opened for user aladin by (uid=0) Aug  7 01:01:52 sabayonx86 NetworkManager: <info>  Updating allowed wireless net work lists. Aug  7 01:01:52 sabayonx86 NetworkManager: <WARN>  nm_dbus_get_networks_cb(): er ror received: org.freedesktop.NetworkManagerInfo.NoNetworks - org.freedesktop.Ne tworkManagerInfo.NoNetworks. Aug  7 01:01:57 sabayonx86 su[9234]: Successful su for root by aladin Aug  7 01:01:57 sabayonx86 su[9234]: + pts/1 aladin:root Aug  7 01:01:57 sabayonx86 su[9234]: pam_unix(su:session): session opened for us er root by (uid=1000) Aug  7 01:02:02 sabayonx86 [   98.906425] PPP generic driver version 2.4.2 Aug  7 01:02:02 sabayonx86 [   98.945284] NET: Registered protocol family 24 Aug  7 01:02:02 sabayonx86 pppd[9302]: invalid numeric parameter 'no ' for idle option Aug  7 01:02:02 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:02:07 sabayonx86 pppd[9305]: invalid numeric parameter 'no ' for idle option Aug  7 01:02:07 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:02:12 sabayonx86 pppd[9313]: invalid numeric parameter 'no ' for idle option Aug  7 01:02:12 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:02:17 sabayonx86 pppd[9317]: invalid numeric parameter 'no ' for idle option Aug  7 01:02:17 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:02:17 sabayonx86 su[9316]: Successful su for root by aladin Aug  7 01:02:17 sabayonx86 su[9316]: + pts/2 aladin:root Aug  7 01:02:17 sabayonx86 su[9316]: pam_unix(su:session): session opened for us er root by (uid=1000) Aug  7 01:02:22 sabayonx86 pppd[9326]: invalid numeric parameter 'no ' for idle option Aug  7 01:02:22 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:02:27 sabayonx86 pppd[9329]: invalid numeric parameter 'no ' for idle option Aug  7 01:02:27 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:02:32 sabayonx86 pppd[9332]: invalid numeric parameter 'no ' for idle option Aug  7 01:02:32 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:02:37 sabayonx86 pppd[9335]: invalid numeric parameter 'no ' for idle option Aug  7 01:02:37 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:02:42 sabayonx86 pppd[9338]: invalid numeric parameter 'no ' for idle option Aug  7 01:02:42 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:02:47 sabayonx86 pppd[9341]: invalid numeric parameter 'no ' for idle option Aug  7 01:02:47 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:02:52 sabayonx86 pppd[9345]: invalid numeric parameter 'no ' for idle option Aug  7 01:02:52 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:02:57 sabayonx86 pppd[9348]: invalid numeric parameter 'no ' for idle option Aug  7 01:02:57 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:03:02 sabayonx86 pppd[9352]: invalid numeric parameter 'no ' for idle option Aug  7 01:03:02 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:03:07 sabayonx86 pppd[9355]: invalid numeric parameter 'no ' for idle option Aug  7 01:03:07 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:03:12 sabayonx86 pppd[9358]: invalid numeric parameter 'no ' for idle option Aug  7 01:03:12 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:03:17 sabayonx86 pppd[9361]: invalid numeric parameter 'no ' for idle option Aug  7 01:03:17 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:03:22 sabayonx86 pppd[9380]: invalid numeric parameter 'no ' for idle option Aug  7 01:03:22 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:03:27 sabayonx86 pppd[9385]: invalid numeric parameter 'no ' for idle option Aug  7 01:03:27 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:03:32 sabayonx86 pppd[9388]: invalid numeric parameter 'no ' for idle option Aug  7 01:03:32 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:03:37 sabayonx86 pppd[9391]: invalid numeric parameter 'no ' for idle option Aug  7 01:03:37 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:03:42 sabayonx86 pppd[9394]: invalid numeric parameter 'no ' for idle option Aug  7 01:03:42 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:03:47 sabayonx86 pppd[9397]: invalid numeric parameter 'no ' for idle option Aug  7 01:03:47 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:03:52 sabayonx86 pppd[9400]: invalid numeric parameter 'no ' for idle option Aug  7 01:03:52 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:03:57 sabayonx86 pppd[9404]: invalid numeric parameter 'no ' for idle option Aug  7 01:03:57 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:04:02 sabayonx86 pppd[9407]: invalid numeric parameter 'no ' for idle option Aug  7 01:04:02 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:04:07 sabayonx86 pppd[9410]: invalid numeric parameter 'no ' for idle option Aug  7 01:04:07 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c onnection. Aug  7 01:04:12 sabayonx86 pppd[9413]: invalid numeric parameter 'no ' for idle option Aug  7 01:04:12 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c                                                                            onnection. Aug  7 01:04:17 sabayonx86 pppd[9416]: invalid numeric parameter 'no ' for idle                                                                             option Aug  7 01:04:17 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c                                                                            onnection. Aug  7 01:04:22 sabayonx86 pppd[9419]: invalid numeric parameter 'no ' for idle                                                                             option Aug  7 01:04:22 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c                                                                            onnection. Aug  7 01:04:27 sabayonx86 pppd[9422]: invalid numeric parameter 'no ' for idle                                                                             option Aug  7 01:04:27 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c                                                                            onnection. Aug  7 01:04:32 sabayonx86 pppd[9425]: invalid numeric parameter 'no ' for idle                                                                             option Aug  7 01:04:32 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c                                                                            onnection. Aug  7 01:04:37 sabayonx86 pppd[9428]: invalid numeric parameter 'no ' for idle                                                                             option Aug  7 01:04:37 sabayonx86 pppoe-connect: PPPoE connection lost; attempting re-c                                                                            onnection. sabayonx86 aladin #

нет нема

[Цитат]

Цитат

s command not foundrt: line 262: : command not foundrt: line 263: : command not foundrt: line 268: sabayonx86 aladin # ifconfig eth0      Link encap:Ethernet  HWaddr 00:15:F2:A1:59:57           inet addr:10.100.46.82  Bcast:10.100.46.255  Mask:255.255.0.0           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1           RX packets:66 errors:0 dropped:0 overruns:0 frame:0           TX packets:34 errors:0 dropped:0 overruns:0 carrier:0           collisions:0 txqueuelen:1000           RX bytes:4004 (3.9 Kb)  TX bytes:6936 (6.7 Kb)           Interrupt:17 Base address:0x2000 lo        Link encap:Local Loopback           inet addr:127.0.0.1  Mask:255.0.0.0           UP LOOPBACK RUNNING  MTU:16436  Metric:1           RX packets:154 errors:0 dropped:0 overruns:0 frame:0           TX packets:154 errors:0 dropped:0 overruns:0 carrier:0           collisions:0 txqueuelen:0           RX bytes:11796 (11.5 Kb)  TX bytes:11796 (11.5 Kb) sabayonx86 aladin # route Kernel IP routing table Destination     Gateway         Genmask         Flags Metric Ref    Use Iface 10.100.0.0      *               255.255.0.0     U     0      0        0 eth0 loopback        *               255.0.0.0       U     0      0        0 lo sabayonx86 aladin #                             aladin@sabayonx86 ~ $ ping 194.145.63.12 connect: Network is unreachable aladin@sabayonx86 ~ $ ping 10.100.46.82 PING 10.100.46.82 (10.100.46.82) 56(84) bytes of data. 64 bytes from 10.100.46.82: icmp_seq=1 ttl=64 time=0.030 ms 64 bytes from 10.100.46.82: icmp_seq=2 ttl=64 time=0.

/etc/conf.d/net

Цитат

# This network configuration was written by net-setup iface_eth0="10.100.46.82 broadcast 10.100.46.255 netmask 255.255.0.0"

[Цитат]

Цитат (arda_kj @ Авг. 06 2007,23:31)

ами даваш му wired, т.е. буквално жична/кабелна връзка, не разбирам кое не ти е ясно. В тоя файл /etc/conf.d/net , който аз нар. интерфейсен файл добавяш config_eth0=( "xxx.xxx.xxx.xxx netmask xxx.xxx.xxx.xxx broadcast xxx.xxx.xxx.xxx" ) Първото xxx... е ИП, второто е netmaskata, а третото е ... абе то си пиши.

Това съм го направил още в 18,30 !
Нет нема!

Примерен код

sabayonx86 aladin # pppoe-start : command not foundrt: line 145: : command not foundrt: line 147: : command not foundrt: line 153: : command not foundrt: line 160: : command not foundrt: line 166: : command not foundrt: line 170: : command not foundrt: line 175: : command not foundrt: line 178: : command not foundrt: line 182: : command not foundrt: line 184: : command not foundrt: line 198: : command not foundrt: line 201: : command not foundrt: line 204: : command not foundrt: line 207: : command not foundrt: line 211: : command not foundrt: line 221: : command not foundrt: line 227: : command not foundrt: line 236: : command not foundrt: line 240: : command not foundrt: line 243: : command not foundrt: line 246: : command not foundrt: line 250: : command not foundrt: line 254: : command not foundrt: line 258: : command not foundrt: line 262: : command not foundrt: line 263: : command not foundrt: line 268: pppoe-start: There already seems to be a PPPoE connection up (PID 9375) sabayonx86 aladin #           ------------------------------ sabayonx86 aladin # grep pppd /var/log/messages  object file: No such file or directory Aug  6 23:51:26 sabayonx86 pppd[5367]: Couldn't load plugin Aug  6 23:51:31 sabayonx86 pppd[8978]: /usr/lib/pppd/2.4.4/ : cannot open shared  object file: No such file or directory Aug  6 23:51:31 sabayonx86 pppd[8978]: Couldn't load plugin Aug  6 23:51:37 sabayonx86 pppd[13693]: /usr/lib/pppd/2.4.4/ : cannot open share d object file: No such file or directory Aug  6 23:51:37 sabayonx86 pppd[13693]: Couldn't load plugin Aug  6 23:51:42 sabayonx86 pppd[18430]: /usr/lib/pppd/2.4.4/ : cannot open share                                                                            d object file: No such file or directory Aug  6 23:51:42 sabayonx86 pppd[18430]: Couldn't load plugin Aug  6 23:51:47 sabayonx86 pppd[23143]: /usr/lib/pppd/2.4.4/ : cannot open share                                                                            d object file: No such file or directory Aug  6 23:51:47 sabayonx86 pppd[23143]: Couldn't load plugin Aug  6 23:51:52 sabayonx86 pppd[26030]: /usr/lib/pppd/2.4.4/ : cannot open share                                                                            d object file: No such file or directory Aug  6 23:51:52 sabayonx86 pppd[26030]: Couldn't load plugin Aug  6 23:51:57 sabayonx86 pppd[28035]: /usr/lib/pppd/2.4.4/ : cannot open share                                                                            d object file: No such file or directory Aug  6 23:51:57 sabayonx86 pppd[28035]: Couldn't load plugin Aug  6 23:52:02 sabayonx86 pppd[30309]: /usr/lib/pppd/2.4.4/ : cannot open share                                                                            d object file: No such file or directory Aug  6 23:52:02 sabayonx86 pppd[30309]: Couldn't load plugin Aug  6 23:52:07 sabayonx86 pppd[32250]: /usr/lib/pppd/2.4.4/ : cannot open share                                                                            d object file: No such file or directory Aug  6 23:52:07 sabayonx86 pppd[32250]: Couldn't load plugin Aug  6 23:52:12 sabayonx86 pppd[1749]: /usr/lib/pppd/2.4.4/ : cannot open shared                                                                             object file: No such file or directory Aug  6 23:52:12 sabayonx86 pppd[1749]: Couldn't load plugin sabayonx86 aladin #

[Цитат]

Цитат (metal @ Авг. 06 2007,20:30)

"DEMAND=no��" - ?!? -> DEMAND=no напиши в конзола (като руут) grep pppd /var/log/messages и дай послените 20-30 реда. П.С. В nano Ctrl+x не е за записване, а за изход от програмата (естествено ако има незаписани промени пита да ги запише ли преди да излезе), а Ctrl+o е за запис

Примерен код

sabayonx86 aladin # pppoe-start : command not foundrt: line 145: : command not foundrt: line 147: : command not foundrt: line 153: : command not foundrt: line 160: : command not foundrt: line 166: : command not foundrt: line 170: : command not foundrt: line 175: : command not foundrt: line 178: : command not foundrt: line 182: : command not foundrt: line 184: : command not foundrt: line 198: : command not foundrt: line 201: : command not foundrt: line 204: : command not foundrt: line 207: : command not foundrt: line 211: : command not foundrt: line 221: : command not foundrt: line 227: : command not foundrt: line 236: : command not foundrt: line 240: : command not foundrt: line 243: : command not foundrt: line 246: : command not foundrt: line 250: : command not foundrt: line 254: : command not foundrt: line 258: : command not foundrt: line 262: : command not foundrt: line 263: : command not foundrt: line 268: pppoe-start: There already seems to be a PPPoE connection up (PID 9375) sabayonx86 aladin #           ------------------------------ sabayonx86 aladin # grep pppd /var/log/messages  object file: No such file or directory Aug  6 23:51:26 sabayonx86 pppd[5367]: Couldn't load plugin Aug  6 23:51:31 sabayonx86 pppd[8978]: /usr/lib/pppd/2.4.4/ : cannot open shared  object file: No such file or directory Aug  6 23:51:31 sabayonx86 pppd[8978]: Couldn't load plugin Aug  6 23:51:37 sabayonx86 pppd[13693]: /usr/lib/pppd/2.4.4/ : cannot open share d object file: No such file or directory Aug  6 23:51:37 sabayonx86 pppd[13693]: Couldn't load plugin Aug  6 23:51:42 sabayonx86 pppd[18430]: /usr/lib/pppd/2.4.4/ : cannot open share                                                                            d object file: No such file or directory Aug  6 23:51:42 sabayonx86 pppd[18430]: Couldn't load plugin Aug  6 23:51:47 sabayonx86 pppd[23143]: /usr/lib/pppd/2.4.4/ : cannot open share                                                                            d object file: No such file or directory Aug  6 23:51:47 sabayonx86 pppd[23143]: Couldn't load plugin Aug  6 23:51:52 sabayonx86 pppd[26030]: /usr/lib/pppd/2.4.4/ : cannot open share                                                                            d object file: No such file or directory Aug  6 23:51:52 sabayonx86 pppd[26030]: Couldn't load plugin Aug  6 23:51:57 sabayonx86 pppd[28035]: /usr/lib/pppd/2.4.4/ : cannot open share                                                                            d object file: No such file or directory Aug  6 23:51:57 sabayonx86 pppd[28035]: Couldn't load plugin Aug  6 23:52:02 sabayonx86 pppd[30309]: /usr/lib/pppd/2.4.4/ : cannot open share                                                                            d object file: No such file or directory Aug  6 23:52:02 sabayonx86 pppd[30309]: Couldn't load plugin Aug  6 23:52:07 sabayonx86 pppd[32250]: /usr/lib/pppd/2.4.4/ : cannot open share                                                                            d object file: No such file or directory Aug  6 23:52:07 sabayonx86 pppd[32250]: Couldn't load plugin Aug  6 23:52:12 sabayonx86 pppd[1749]: /usr/lib/pppd/2.4.4/ : cannot open shared                                                                             object file: No such file or directory Aug  6 23:52:12 sabayonx86 pppd[1749]: Couldn't load plugin sabayonx86 aladin #

Добрата новина е ,че с net-setup успях да задам IP и маска!
Обаче при настройката ме пита Wirless или Wired  network !

[Цитат]

Цитат (Ivaylo78 @ Авг. 06 2007,19:35)

Пак не става. '>

Споко,и при ен е така '>

Цитат

Section "InputDevice"    Identifier   "Generic Keyboard"    Driver      "kbd"    Option      "CoreKeyboard"    Option      "XkbRules"   "xorg"    Option      "XkbModel"   "pc105"    Option      "XkbLayout"   "us,bg"    Option      "XkbVariant"   ",phonetic"    Option      "XkbOptions"   "grp:alt_shift_toggle,grp_led:scroll" EndSection

[Цитат]

/etc/conf.d/net

Цитат

# This blank configuration will automatically use DHCP for any net.* # scripts in /etc/init.d.  To create a more complete configuration, # please review /etc/conf.d/net.example and save your configuration # in /etc/conf.d/net (this file :]!'>. # modules=( "dhclient" ) plug_timeout="6" dhcp_eth0="nosendhost" dhcp_eth1="nosendhost" dhcp_eth2="nosendhost" dhcp_wlan0="nosendhost" dhcp_ath0="nosendhost" dhcp_ra0="nosendhost" dns_domain_eth0="localdomain" nis_domain_eth0="localdomain"

/media/hda5/etc/ppp/pppoe.conf

Цитат

#*********************************************************************** # # pppoe.conf # # Configuration file for rp-pppoe.  Edit as appropriate and install in # /etc/ppp/pppoe.conf # # NOTE: This file is used by the pppoe-start, pppoe-stop, pppoe-connect and #       pppoe-status shell scripts.  It is *not* used in any way by the #       "pppoe" executable. # # Copyright © 2000 Roaring Penguin Software Inc. # # This file may be distributed under the terms of the GNU General # Public License. # # LIC: GPL # $Id: pppoe.conf,v 1.11 2005/08/09 02:49:12 dfs Exp $ #*********************************************************************** # When you configure a variable, DO NOT leave spaces around the "=" sign. # Ethernet card connected to DSL modem # # NB: Gentoo overrides ETH when pppoe-start is called from the # networking scripts.  This setting has no effect in that case. ETH='eth0' # PPPoE user name.  You may have to supply "@provider.com"  Sympatico # users in Canada do need to include "@sympatico.ca" # Sympatico uses PAP authentication.  Make sure /etc/ppp/pap-secrets # contains the right username/password combination. # For Magma, use xxyyzz@magma.ca USER='kl34814' # Bring link up on demand?  Default is to leave link up all the time. # If you want the link to come up on demand, set DEMAND to a number indicating # the idle time after which the link is brought down. DEMAND=no�� #DEMAND=300 # DNS type: SERVER=obtain from server; SPECIFY=use DNS1 and DNS2; # NOCHANGE=do not adjust. DNSTYPE=NOCHANGE # Obtain DNS server addresses from the peer (recent versions of pppd only) # In old config files, this used to be called USEPEERDNS.  Changed to # PEERDNS for better Red Hat compatibility PEERDNS=yes DNS1= DNS2= # Make the PPPoE connection your default route.  Set to # DEFAULTROUTE=no if you don't want this. DEFAULTROUTE=yes ### ONLY TOUCH THE FOLLOWING SETTINGS IF YOU'RE AN EXPERT # How long pppoe-start waits for a new PPP interface to appear before # concluding something went wrong.  If you use 0, then pppoe-start # exits immediately with a successful status and does not wait for the # link to come up.  Time is in seconds. # # WARNING WARNING WARNING: # # If you are using rp-pppoe on a physically-inaccessible host, set # CONNECT_TIMEOUT to 0.  This makes SURE that the machine keeps trying # to connect forever after pppoe-start is called.  Otherwise, it will # give out after CONNECT_TIMEOUT seconds and will not attempt to # connect again, making it impossible to reach. CONNECT_TIMEOUT=30 # How often in seconds pppoe-start polls to check if link is up CONNECT_POLL=2 # Specific desired AC Name ACNAME= # Specific desired service name SERVICENAME=koel # Character to echo at each poll.  Use PING="" if you don't want # anything echoed PING="." # File where the pppoe-connect script writes its process-ID. # Three files are actually used: #   $PIDFILE       contains PID of pppoe-connect script #   $PIDFILE.pppoe contains PID of pppoe process #   $PIDFILE.pppd  contains PID of pppd process # # NB: Gentoo overrides PIDFILE when pppoe-start is run from the # networking scripts.  This setting has no effect in that case. PIDFILE="/var/run/$CF_BASE-pppoe.pid" # Do you want to use synchronous PPP?  "yes" or "no".  "yes" is much # easier on CPU usage, but may not work for you.  It is safer to use # "no", but you may want to experiment with "yes".  "yes" is generally # safe on Linux machines with the n_hdlc line discipline; unsafe on others. SYNCHRONOUS=no # Do you want to clamp the MSS?  Here's how to decide: # - If you have only a SINGLE computer connected to the DSL modem, choose #   "no". # - If you have a computer acting as a gateway for a LAN, choose "1412". #   The setting of 1412 is safe for either setup, but uses slightly more #   CPU power. CLAMPMSS=1412 #CLAMPMSS=no # LCP echo interval and failure count. LCP_INTERVAL=20 LCP_FAILURE=3 # PPPOE_TIMEOUT should be about 4*LCP_INTERVAL PPPOE_TIMEOUT=80 # Firewalling: One of NONE, STANDALONE or MASQUERADE FIREWALL=NONE # Linux kernel-mode plugin for pppd.  If you want to try the kernel-mode # plugin, use LINUX_PLUGIN=rp-pppoe.so LINUX_PLUGIN= # Any extra arguments to pass to pppoe.  Normally, use a blank string # like this: PPPOE_EXTRA="" # Rumour has it that "Citizen's Communications" with a 3Com # HomeConnect DSL Modem DualLink requires these extra options: # PPPOE_EXTRA="-f 3c12:3c13 -S ISP" # Any extra arguments to pass to pppd.  Normally, use a blank string # like this: PPPD_EXTRA="" ########## DON'T CHANGE BELOW UNLESS YOU KNOW WHAT YOU ARE DOING # If you wish to COMPLETELY overrride the pppd invocation: # Example: # OVERRIDE_PPPD_COMMAND="pppd call dsl" # If you want pppoe-connect to exit when connection drops: # RETRY_ON_FAILURE=no

Не съм в нас за да го пробвам!/не четеш-казах че после ще пробвам/
Довечера  '>

Сега обаче спирам да пиша ,че съм малко зает-гледам "Блясък" по Нова ТВ ,2348 серия  '>

едит: почна 2349 серия  

[Цитат]

Цитат (Ivaylo78 @ Авг. 06 2007,16:22)

Стана както стеалтх каза, но не мога да наглася смяната на езиците да бъде  от клавиатурата.

Абе човек,постни като ти казал човека !Как да ти помогнем като нищо не пишеш  '>

Между другото-вчера тъкмо се чудех в Kubuntu  дали няма такава опция!

[Примерен код]

казах ти че съм променил всичко,както сте посочили/за трети път го пиша/ и ми изкарва не може да локализира мрежово устройство за конектване,
Това е!

днес видях как  се вкарват IP  и маска в конзола  на Дебиан

Примерен код

sudo: pass: nano  /var/lib/dhcp/dhclient.etho.lases

Отваря се  файла  /nano е текстов редактор/  и се пишат IP и маската.

след това се запомня с Ctrl+X и се рестартира мрежата.

Примерен код

sudo: pass: /etc/init.d/networking restart

и това е:
ls=dir  при windows
cd... си е cd

a при Gentoo как е?

[Цитат]

Цитат (ivo1204 @ Авг. 06 2007,03:04)

@aladin kak e 3D -to ?

Идеал!
За сметка на мрежата!

така че помагай

metal,нали съм постнал съдържанието на файла,защо мислиш че те лъжа

Примерен код

rc-update del NetworkManager rc-update del dhcdbd

След това да редактира файла с интерфейсите като добави този ред:

Примерен код

config_eth0=( "xxx.xxx.xxx.xxx netmask xxx.xxx.xxx.xxx broadcast xxx.xxx.xxx.xxx" )

След, което рестарт на мрежата:

Примерен код

/etc/init.d/net.eth0 restart

после ще пробвам това!
Не знаех че става така.
просто под кубунто става интуитивно и лесно,а тук не

Тук намерих за Gentoo как става!
Дано и за Sabayon-a е същото!

Цитат

Ако все още нямате достъп до мрежата, може да използвате net-setup за конфигуриране на мрежата. Може да се наложи да заредите нужния модул за вашата мрежова карта, посредством modprobe, преди да пристъпите към конфигуриране. Ако имате ADSL, използвайте pppoe-setup и pppoe-start.

Цитат

Ако имате безжична връзка, трябва да използвате iwconfig, за да настроите параметрите й, и след това може да стартирате net-setup отново, или да настроите ръчно интерфейса чрез ifconfig, dhcpcd -d -t 15 <interface>.

IP-то ми не е статично,а локално-само IP и маска трябва да задам!
Досега четох в официяния сайт,но нищо!

[Примерен код]

Примерен код

#*********************************************************************** # # pppoe.conf # # Configuration file for rp-pppoe.  Edit as appropriate and install in # /etc/ppp/pppoe.conf # # NOTE: This file is used by the pppoe-start, pppoe-stop, pppoe-connect and #       pppoe-status shell scripts.  It is *not* used in any way by the #       "pppoe" executable. # # Copyright (C) 2000 Roaring Penguin Software Inc. # # This file may be distributed under the terms of the GNU General # Public License. # # LIC: GPL # $Id: pppoe.conf,v 1.11 2005/08/09 02:49:12 dfs Exp $ #*********************************************************************** # When you configure a variable, DO NOT leave spaces around the "=" sign. # Ethernet card connected to DSL modem # # NB: Gentoo overrides ETH when pppoe-start is called from the # networking scripts.  This setting has no effect in that case. ETH='eth0' # PPPoE user name.  You may have to supply "@provider.com"  Sympatico # users in Canada do need to include "@sympatico.ca" # Sympatico uses PAP authentication.  Make sure /etc/ppp/pap-secrets # contains the right username/password combination. # For Magma, use xxyyzz@magma.ca USER='kl34814' # Bring link up on demand?  Default is to leave link up all the time. # If you want the link to come up on demand, set DEMAND to a number indicating # the idle time after which the link is brought down. DEMAND=10 #DEMAND=300 # DNS type: SERVER=obtain from server; SPECIFY=use DNS1 and DNS2; # NOCHANGE=do not adjust. DNSTYPE=server # Obtain DNS server addresses from the peer (recent versions of pppd only) # In old config files, this used to be called USEPEERDNS.  Changed to # PEERDNS for better Red Hat compatibility PEERDNS=no DNS1= DNS2= # Make the PPPoE connection your default route.  Set to # DEFAULTROUTE=no if you don't want this. DEFAULTROUTE=yes ### ONLY TOUCH THE FOLLOWING SETTINGS IF YOU'RE AN EXPERT # How long pppoe-start waits for a new PPP interface to appear before # concluding something went wrong.  If you use 0, then pppoe-start # exits immediately with a successful status and does not wait for the # link to come up.  Time is in seconds. # # WARNING WARNING WARNING: # # If you are using rp-pppoe on a physically-inaccessible host, set # CONNECT_TIMEOUT to 0.  This makes SURE that the machine keeps trying # to connect forever after pppoe-start is called.  Otherwise, it will # give out after CONNECT_TIMEOUT seconds and will not attempt to # connect again, making it impossible to reach. CONNECT_TIMEOUT=30 # How often in seconds pppoe-start polls to check if link is up CONNECT_POLL=2 # Specific desired AC Name ACNAME= # Specific desired service name SERVICENAME=koel # Character to echo at each poll.  Use PING="" if you don't want # anything echoed PING="." # File where the pppoe-connect script writes its process-ID. # Three files are actually used: #   $PIDFILE       contains PID of pppoe-connect script #   $PIDFILE.pppoe contains PID of pppoe process #   $PIDFILE.pppd  contains PID of pppd process # # NB: Gentoo overrides PIDFILE when pppoe-start is run from the # networking scripts.  This setting has no effect in that case. PIDFILE="/var/run/$CF_BASE-pppoe.pid" # Do you want to use synchronous PPP?  "yes" or "no".  "yes" is much # easier on CPU usage, but may not work for you.  It is safer to use # "no", but you may want to experiment with "yes".  "yes" is generally # safe on Linux machines with the n_hdlc line discipline; unsafe on others. SYNCHRONOUS=no # Do you want to clamp the MSS?  Here's how to decide: # - If you have only a SINGLE computer connected to the DSL modem, choose #   "no". # - If you have a computer acting as a gateway for a LAN, choose "1412". #   The setting of 1412 is safe for either setup, but uses slightly more #   CPU power. CLAMPMSS=1412 #CLAMPMSS=no # LCP echo interval and failure count. LCP_INTERVAL=20 LCP_FAILURE=3 # PPPOE_TIMEOUT should be about 4*LCP_INTERVAL PPPOE_TIMEOUT=80 # Firewalling: One of NONE, STANDALONE or MASQUERADE FIREWALL=NONE # Linux kernel-mode plugin for pppd.  If you want to try the kernel-mode # plugin, use LINUX_PLUGIN=rp-pppoe.so LINUX_PLUGIN= # Any extra arguments to pass to pppoe.  Normally, use a blank string # like this: PPPOE_EXTRA="" # Rumour has it that "Citizen's Communications" with a 3Com # HomeConnect DSL Modem DualLink requires these extra options: # PPPOE_EXTRA="-f 3c12:3c13 -S ISP" # Any extra arguments to pass to pppd.  Normally, use a blank string # like this: PPPD_EXTRA="" ########## DON'T CHANGE BELOW UNLESS YOU KNOW WHAT YOU ARE DOING # If you wish to COMPLETELY overrride the pppd invocation: # Example: # OVERRIDE_PPPD_COMMAND="pppd call dsl" # If you want pppoe-connect to exit when connection drops: # RETRY_ON_FAILURE=no

как според вас да задам ip-то така,че да е както трябва.
защото нета ми е като за начало по ip и МАС адрес,после по user/pass

[и както metal го е написал]

Това го промених,точно както си го написал  и както metal го е написал
Още преди!
Това което поствам са резултати след промяната!
Така че   '>

IP-то се опитвам през някакъв менижър да го напиша,но явно не се запомня!През KNetworkmanager нямам опция за промяна!

На Kubuntu  го пиша през KNetworkmanager, sudo pppoeconf,ентере,ентер,пиша  име и парола и всичко е 6!

А тука с тия упражнения  

Поне 3D-то на Ati бачка от раз,има и  доста игри и програмки!

Примерен код

# This blank configuration will automatically use DHCP for any net.* # scripts in /etc/init.d.  To create a more complete configuration, # please review /etc/conf.d/net.example and save your configuration # in /etc/conf.d/net (this file :]!). # modules=( "dhclient" ) plug_timeout="6" dhcp_eth0="nosendhost" dhcp_eth1="nosendhost" dhcp_eth2="nosendhost" dhcp_wlan0="nosendhost" dhcp_ath0="nosendhost" dhcp_ra0="nosendhost" dns_domain_eth0="localdomain" nis_domain_eth0="localdomain"

IP-то как се задава ръчно

IP-то ми трябва да е :

10.100.46.82
255.255.0.0

какви са тия ip-та горе дето излизат не знам,да не са някакви външни?