Изпечатай

[alkor]

Проблема е следни. След инсталация на  Slackware12 конфигурирам pppoe по следния начин. На Bolbg  съм ако е от значение.

Примерен код

root@darkstar:~# pppoe-setup Welcome to the Roaring Penguin PPPoE client setup.  First, I will run some checks on your system to make sure the PPPoE client is installed properly... Looks good!  Now, please enter some information: USER NAME >>> Enter your PPPoE user name (default bxxxnxnx@sympatico.ca): feniks INTERFACE >>> Enter the Ethernet interface connected to the DSL modem For Solaris, this is likely to be something like /dev/hme0. For Linux, it will be ethn, where 'n' is a number. (default eth0): default eth0 Do you want the link to come up on demand, or stay up continuously? If you want it to come up on demand, enter the idle time in seconds after which the link should be dropped.  If you want the link to stay up permanently, enter 'no' (two letters, lower-case.) NOTE: Demand-activated links do not interact well with dynamic IP addresses.  You may have some problems with demand-activated links. >>> Enter the demand value (default no): DNS Please enter the IP address of your ISP's primary DNS server. If your ISP claims that 'the server will provide DNS addresses', enter 'server' (all lower-case) here. If you just press enter, I will assume you know what you are doing and not modify your DNS setup. >>> Enter the DNS information here:  server PASSWORD >>> Please enter your PPPoE password: >>> Please re-enter your PPPoE password: FIREWALLING Please choose the firewall rules to use.  Note that these rules are very basic.  You are strongly encouraged to use a more sophisticated firewall setup; however, these will provide basic security.  If you are running any servers on your machine, you must choose 'NONE' and set up firewalling yourself.  Otherwise, the firewall rules will deny access to all standard servers like Web, e-mail, ftp, etc.  If you are using SSH, the rules will block outgoing SSH connections which allocate a privileged source port. The firewall choices are: 0 - NONE: This script will not set any firewall rules.  You are responsible           for ensuring the security of your machine.  You are STRONGLY           recommended to use some kind of firewall rules. 1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation 2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway                 for a LAN >>> Choose a type of firewall (0-2): 1 ** Summary of what you entered ** Ethernet Interface: default eth0 User name:          feniks Activate-on-demand: No DNS addresses:      Supplied by ISP's server Firewalling:        STANDALONE >>> Accept these settings and adjust configuration files (y/n)? y Adjusting /etc/ppp/pppoe.conf Adjusting /etc/ppp/pap-secrets and /etc/ppp/chap-secrets   (But first backing it up to /etc/ppp/pap-secrets-bak)   (But first backing it up to /etc/ppp/chap-secrets-bak) Congratulations, it should be all set up! Type 'pppoe-start' to bring up your PPPoE link and 'pppoe-stop' to bring it down.  Type 'pppoe-status' to see the link status. root@darkstar:~# pppoe-start ................TIMED OUT root@darkstar:~#

 Нет със сигурност имам, имам инсталиран и Debian и при него няма ма никакъв проблем.

[alkor]

Това даде след рестарт

Цитат

root@darkstar:~# pppoe-start ................TIMED OUT /usr/sbin/pppoe-start: line 191:  3608 Terminated              $CONNECT "$@" >/d     ev/null 2>&1 root@darkstar:~# pppoe-start ................TIMED OUT root@darkstar:~#

[kas81]

ако си сигурен, че имаш физическа връзка пробвай без файрлол, спомням си че, слака имаше някаква особеност с фаирлола на пппое-то..... и другото за което се сещам е default gateway-a да не ти е наред(по-вероятното)..... по-коомпетентните да дават на там ...