Нямам такъв пакет в мирърите на магеята:
[root@localhost ~]# smartctl --all /dev/sda
-bash: smartctl: command not found
[root@localhost ~]# urpmq -y smartctl
No package named smartctl
[root@localhost ~]# urpmq -y smart
golang-github-smartystreets-assertions-devel
golang-github-smartystreets-goconvey-devel
gsmartcontrol
json-smart
json-smart-javadoc
lib64atasmart-devel
lib64atasmart4
lib64smartcols-devel
lib64smartcols1
libatasmart
libatasmart-devel
libatasmart4
libsmartcols-devel
libsmartcols1
lucene-analyzers-smartcn
nagios-check_ide_smart
php-smarty
php-smarty-doc
php-smarty-gettext
php-smarty-gettext-devel
smartmontools
xfce4-smartbookmark-plugin
[root@localhost ~]#
по-горното е всичко в мирърите, което съдържа в себе си "smart".
Благодаря за отговора, явно харда си заминава, все пак.
П.П. почетох малко, след търсене в нета за smartctl, излезе това:
https://www.smartmontools.org/Демек при мен в мирърите го има- по-горе gsmartcontrol
Инсталирах го:
[root@localhost ~]# urpmi gsmartcontrol
To satisfy dependencies, the following packages are going to be installed:
Package Version Release Arch
(medium "Core Release")
gsmartcontrol 0.9.0 1.mga6 x86_64
smartmontools 6.5 1.mga6 x86_64
3.4MB of additional disk space will be used.
1MB of packages will be retrieved.
Proceed with the installation of the 2 packages? (Y/n) y
http://distrib-coffee.ipsl.jussieu.fr/pub/linux/Mageia-archive/distrib/6/x86_64/media/core/release/smartmontools-6.5-1.mga6.x86_64.rpm http://distrib-coffee.ipsl.jussieu.fr/pub/linux/Mageia-archive/distrib/6/x86_64/media/core/release/gsmartcontrol-0.9.0-1.mga6.x86_64.rpminstalling smartmontools-6.5-1.mga6.x86_64.rpm gsmartcontrol-0.9.0-1.mga6.x86_64.rpm from /var/cache/urpmi/rpms
Preparing... #############################################
1/2: smartmontools #############################################
2/2: gsmartcontrol #############################################
[root@localhost ~]#
Сега остана да го разгледам, това, и как се ползва, очевидно е софтуер за диагностика на харда. Още веднъж благодаря, Нака!
П.П.П. Ето и изхода от командата smartctl --all /dev/sda , след като инсталирах gsmartcontrol :
[root@localhost ~]# smartctl --all /dev/sda
smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.14.145-desktop-2.mga6] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke,
http://www.smartmontools.org=== START OF INFORMATION SECTION ===
Model Family: Seagate Samsung SpinPoint M8 (AF)
Device Model: ST1000LM024 HN-M101MBB
Serial Number: S2SMJ9AF300588
LU WWN Device Id: 5 0004cf 20cbee25d
Firmware Version: 2AR20002
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Tue Aug 15 17:53:10 2023 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (13080) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 218) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 41
2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0
3 Spin_Up_Time 0x0023 090 088 025 Pre-fail Always - 3058
4 Start_Stop_Count 0x0032 092 092 000 Old_age Always - 8114
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 23748
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 206
12 Power_Cycle_Count 0x0032 092 092 000 Old_age Always - 8179
191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 39
192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 056 031 000 Old_age Always - 44 (Min/Max 11/69)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 252 252 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 15984
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 206
225 Load_Cycle_Count 0x0032 001 001 000 Old_age Always - 1848493
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Vendor (0x50) Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
[root@localhost ~]#