Титла: Shoutcast
Публикувано от: h7d8 в Apr 17, 2008, 01:40
Здравейте ,реших да пусна Shoutcast на сървър-а и да сложа хард диск да си складирам на него мп3-тата и така да се слушат из локалната мрежа (20-30 машини).Главната идея е ,когато някой реши да слуша да няма нужда от пуснат winamp който да прави листинг.За целта от ровенето из интернет разбрах ,че се ползва sc_trans_posix_040.tgz заедно с sc_serv_1.9.8_Linux.tar.gz (серв-а).Проблема е там ,че след конфигурирането на файловете и стартирането на демоните пак неможе да се закачи и да слуша никой.Може ли някой да ми помогне с example conf файлове други настройки и стартиране?Как се сваля файла (генерираната листа с мп3) гропирането им по стилове и прочие?Доста се рових из нета ,но всичко е до ./sc_serv & и толкова.Не търся съвършенство ,а ефекта който върши работа.Благодаря предварително!
Титла: Shoutcast
Публикувано от: h7d8 в Apr 19, 2008, 21:30
Със сървър-а се справих работи ,но пак проблем...плугин-а sc_trans_linux който ползвам да се закача към сървър-а вместо мен с winamp не тръгва.Когато обаче пусна winamp с DSP плугина се закача и стреемва без проблем.
Титла: Shoutcast
Публикувано от: Nikolavp в Apr 20, 2008, 08:29
Цитат (h7d8 @ Април 19 2008,22:30) | Със сървър-а се справих работи ,но пак проблем...плугин-а sc_trans_linux който ползвам да се закача към сървър-а вместо мен с winamp не тръгва.Когато обаче пусна winamp с DSP плугина се закача и стреемва без проблем. |
Метни един поглед на това
Титла: Shoutcast
Публикувано от: h7d8 в Apr 20, 2008, 18:21
Да това всичко съм го правил..все пак сега повторих и пак не става.Проблема явно не е в сървър-а ,а е в trans-a.Конфигурирам го правилно ,но когато го стартирам явно не се закача към сървър-а..сигурно неможе но каква ще е причината след като с DSP plugin-a на winamp-a щом чукна адреса и паролата ,дам конект се закача.След това вече като адна URL-то в winamp и си тръгва всичко.
Титла: Shoutcast
Публикувано от: Bogo в Apr 22, 2008, 00:11
Какво пише в лога като причина?
Титла: Shoutcast
Публикувано от: eniac111 в Apr 22, 2008, 16:50
Не съм много наясно, но IceCast не Ти ли върши работа?
Титла: Shoutcast
Публикувано от: h7d8 в Aug 27, 2008, 18:51
Цитат (Bogo @ Април 22 2008,03:11) | Какво пише в лога като причина? |
Примерен код | shoutcast@stoyanov:~/radio$ nohup ./sc_serv & [1] 5108 nohup: appending output to `nohup.out' shoutcast@stoyanov:~/radio$ nohup ./sc_trans_linux & [2] 5172 shoutcast@stoyanov:~/radio$ nohup: appending output to `nohup.out'
|
nohup.out ->
Примерен код | <08/28/08@18:46:50> [STREAM] Creating stream socket ******************************************************************************* ** TRANScast Distributed Network Audio Content Provider ** Copyright (C) 2000 Nullsoft, Inc. All Rights Reserved. ** Use "sc_trans filename.conf" to specify a config file. ******************************************************************************* <08/28/08@18:48:41> [TRANSCast] DNAS/posix v0.400-LAME (Mar 4 2003) starting up... <08/28/08@18:48:41> [MAIN] PID: 5172 <08/28/08@18:48:41> [MAIN] Loaded config from sc_trans.conf <08/28/08@18:48:41> [MAIN] Loading playlist (/home/shoutcast/radio/house.m3u) <08/28/08@18:48:41> [MAIN] Found (4) entries in playlist <08/28/08@18:48:41> [MAIN] Playlist decoder thread starting <08/28/08@18:48:41> [MAIN] Streaming thread starting <08/28/08@18:48:41> [DECODE] Opened 06-steve_mac_and_paul_harris-you_(fps_remix).mp3 <08/28/08@18:48:41> [STREAM] Creating stream socket <08/28/08@18:48:41> [CONFIG] WARNING: No InputSamplerate defined, assuming 44100! <08/28/08@18:48:41> [CONFIG] WARNING: No InputChannels defined, assuming 2! <08/28/08@18:48:41> Warning: input file samplerate is -1208237319 Hz, must be 44100! <08/28/08@18:48:42> [DECODE] Opened Ismael_Rivas_Luxtro_(Original_Mix).mp3
|
sc_serv.log ->
Примерен код | <08/28/08@18:48:35> [SHOUTcast] DNAS/Linux v1.9.8 (Feb 28 2007) starting up... <08/28/08@18:48:35> [main] pid: 5108 <08/28/08@18:48:35> [main] loaded config from sc_serv.conf <08/28/08@18:48:35> [main] initializing (usermax:30 portbase:8000)... <08/28/08@18:48:35> [main] No ban file found (sc_serv.ban) <08/28/08@18:48:35> [main] No rip file found (sc_serv.rip) <08/28/08@18:48:35> [main] opening source socket <08/28/08@18:48:35> [main] source thread starting <08/28/08@18:48:35> [main] opening client socket <08/28/08@18:48:35> [main] Client Stream thread [0] starting <08/28/08@18:48:35> [main] client main thread starting <08/28/08@18:48:35> [source] listening for connection on port 8001 <08/28/08@18:49:07> [dest: 192.168.2.100] server unavailable, disconnecting <08/28/08@18:49:08> [dest: 192.168.2.100] server unavailable, disconnecting <08/28/08@18:49:08> [dest: 192.168.2.100] server unavailable, disconnecting <08/28/08@18:49:08> [dest: 192.168.2.100] server unavailable, disconnecting <08/28/08@18:49:09> [dest: 192.168.2.100] server unavailable, disconnecting <08/28/08@18:49:09> [dest: 192.168.2.100] server unavailable, disconnecting
|
sc_trans.log ->
Примерен код | <08/28/08@18:46:40> [STREAM] Error connecting to stream host [waiting 10s] <08/28/08@18:46:42> [MAIN] Title Update Failed <08/28/08@18:46:50> [STREAM] Creating stream socket <08/28/08@18:48:41> [TRANSCast] DNAS/posix v0.400-LAME (Mar 4 2003) starting up... <08/28/08@18:48:41> [MAIN] PID: 5172 <08/28/08@18:48:41> [MAIN] Loaded config from sc_trans.conf <08/28/08@18:48:41> [MAIN] Loading playlist (/home/shoutcast/radio/house.m3u) <08/28/08@18:48:41> [MAIN] Found (4) entries in playlist <08/28/08@18:48:41> [MAIN] Playlist decoder thread starting <08/28/08@18:48:41> [MAIN] Streaming thread starting <08/28/08@18:48:41> [DECODE] Opened 06-steve_mac_and_paul_harris-you_(fps_remix).mp3 <08/28/08@18:48:41> [STREAM] Creating stream socket <08/28/08@18:48:41> [CONFIG] WARNING: No InputSamplerate defined, assuming 44100! <08/28/08@18:48:41> [CONFIG] WARNING: No InputChannels defined, assuming 2! <08/28/08@18:48:41> Warning: input file samplerate is -1208237319 Hz, must be 44100! <08/28/08@18:48:42> [DECODE] Opened Ismael_Rivas_Luxtro_(Original_Mix).mp3
|
ps x
Примерен код | ps x PID TTY STAT TIME COMMAND 19865 ? S 0:02 sshd: shoutcast@pts/0 19872 pts/0 Ss 0:02 -bash 5108 pts/0 Sl 0:00 ./sc_serv 5172 pts/0 Sl 0:12 ./sc_trans_linux 6852 pts/0 R+ 0:00 ps x shoutcast@stoyanov:~/radio$
|
Според мен всичко е добре в конфа ,а излиза тази грешка.Толкова пък да неможе да тръгне едно радио...то това ще е голяма каръщина.
Титла: Shoutcast
Публикувано от: edmon в Aug 28, 2008, 01:16
защо имам чувството че: апт-гет инсталл ицецаст
ще ти реши всчки проблеми?
Титла: Shoutcast
Публикувано от: h7d8 в Aug 28, 2008, 01:33
Цитат (edmon @ Авг. 28 2008,04:16) | защо имам чувството че: апт-гет инсталл ицецаст
ще ти реши всчки проблеми? |
Да ,сигурно го има този момент ,но пък съм подготвил доста скриптове за статистики и уеб приложения към shoutcast.Като цяло мисля ,че shoutcast e по-добър за подобна работа.Това е мое мнение.Незнам защо ,но съм се насочил към него.Ако наистина icecast е по-добър трябва бая предимства да изтъкеш ,че да ми излезе явното пред очите. Занимавах се малко с icecast ,но да ти кажа след като ми поиска незнам си какви кодери декодери за работа с .mp3 формат се отказах.
Титла: Shoutcast
Публикувано от: Warstomp в Aug 28, 2008, 08:38
Какво има в този .conf файл?
Титла: Shoutcast
Публикувано от: h7d8 в Aug 28, 2008, 13:48
Цитат (MaX_Ass @ Авг. 28 2008,11:38) | Какво има в този .conf файл? |
Те са два конфиг. файла.Този на serv-a и този за листинг. sc_serv.conf ->
Примерен код | ; SHOUTcast Distributed Network Audio Server configuration file ; Copyright (C) 1998-2004 Nullsoft, Inc. ; All Rights Reserved. ; Last modified Mar 17 2004
; If you want to manage multiple configurations, just copy ; this file to another name, and run sc_serv with that name ; such as: ; sc_serv.exe sc_leet.conf
; *************************** ; Required stuff ; ***************************
; MaxUser. The maximum number of simultaneous listeners allowed. ; Compute a reasonable value for your available upstream bandwidth (i.e. if ; you have 256kbps upload DSL, and want to broadcast at 24kbps, you would ; choose 256kbps/24kbps=10 maximum listeners.) Setting this value higher ; only wastes RAM and screws up your broadcast when more people connect ; than you can support. MaxUser=10
; Password. While SHOUTcast never asks a listener for a password, a ; password is required to broadcast through the server, and to perform ; administration via the web interface to this server. This server should ; consist of only letters and numbers, and is the same server your broadcaster ; will need to enter in the SHOUTcast Source Plug-in for Winamp. THIS VALUE ; CANNOT BE BLANK. Password=blablabla
; PortBase. This is the IP port number your server will run on. The ; value, and the value + 1 must be available. If you get a fatal error when ; the DNAS is setting up a socket on startup, make sure nothing else on the ; machine is running on the same port (telnet localhost portnumber -- if you ; get connection refused then you're clear to use that port). Ports < 1024 ; may require root privledges on *nix machines. The default port is 8000. PortBase=8000
; *************************** ; Optional Parameters ; ***************************
; *************************** ; Logging configuration ; ***************************
; LogFile: file to use for logging. Can be '/dev/null' or 'none' ; or empty to turn off logging. The default is ./sc_serv.log ; on *nix systems or sc_serv_dir\sc_serv.log on win32. ; Note: on win32 systems if no path is specified the location is ; in the same dir as the executable, on *nix systems it is in the ; current directory. LogFile=sc_serv.log
; RealTime displays a status line that is updated every second ; with the latest information on the current stream (*nix and win32 ; console systems only) RealTime=0
; ScreenLog controls whether logging is printed to the screen or not ; on *nix and win32 console systems. It is useful to disable this when ; running servers in background without their own terminals. Default is 1 ScreenLog=1
; ShowLastSongs specifies how many songs to list in the /played.html ; page. The default is 10. Acceptable entries are 1 to 20. ShowLastSongs=10
; TchLog decides whether or not the DNAS logfile should track yp ; directory touches. Adds and removes still appear regardless of ; this setting. ; Default is yes ; TchLog=yes
; WebLog decides whether or not hits to http:// on this DNAS will ; be logged. Most people leave this off because the DSP plug-in ; uses http:// calls to update titles and get the listener count, ; which takes up a lot of log space eventually. If you want to ; see people making hits on your admin.cgi or index pages, turn ; this back on. Note that this setting does NOT affect XML stats ; counters for hits to http:// pages. ; Default is no. ; WebLog=no
; W3CEnable turns on W3C Logging. W3C logs contain httpd-like accounts ; of every track played for every listener, including byte counts those listeners ; took. This data can be parsed with tools like Analog and WebTrends, or given ; to third parties like Arbitron and Measurecast for their reporting systems. ; Default is Yes (enabled). ;W3CEnable=Yes
; W3CLog describes the name of the logfile for W3C logging. Default logfile is ; sc_w3c.log, in the same directory wherever the DNAS gets started from. ;W3CLog=sc_w3c.log
; *************************** ; Network configuration ; ***************************
; SrcIP, the interface to listen for source connections on (or to make relay ; connections on if relaying). Can and usually will be ANY or 127.0.0.1 ; (Making it 127.0.0.1 will keep other machines from being able to ; broadcast using your shoutcast server ) SrcIP=ANY
; DestIP, IP to listen for clients on (and to contact yp.shoutcast.com) ; can and usually will be be ANY. If your machine has multiple IP addresses, ; set this to the one you want it to be accessed by. DestIP=ANY
; Yport, port to connect to yp.shoutcast.com on. For people behind caching ; webproxies, change this to the alternate port (666 is what it might be, ; check www.shoutcast.com if you have problems). Otherwise, leave this at 80. ; We're actively working on re-opening port 666, but as of release the only ; working port is port 80. Yport=80
; NameLookups. Specify 1 to perform reverse DNS on connections. ; This option may increase the time it takes to connect to your ; server if your DNS server is slow. Default is 0 (off). NameLookups=0
; RelayPort and RelayServer specify that you want to be a relay server. ; Relay servers act as clients to another server, and rebroadcast. ; Set RelayPort to 0, RelayServer to empty, or just leave these commented ; out to disable relay mode. ; RelayPort=8000 ; RelayServer=192.168.1.58
; *************************** ; Server configuration ; ***************************
; AdminPassword. This password (if specified) changes the ; behavior of Password to be a broadcast-only password, and ; limits HTTP administration tasks to the password specified ; here. The broadcaster, with the password above, can still ; log in and view connected users, but only the AdminPassword ; will grant the right to kick, ban, and specify reserve hosts. ; The default is undefined (Password allows control for both ; source and admin) ; AdminPassword=adminpass
; AutoDumpUsers controls whether listeners are disconnected if the source ; stream disconnects. The default is 0. AutoDumpUsers=0
; AutoDumpSourceTime specifies how long, in seconds, the source stream is ; allowed to be idle before the server disconnects it. 0 will let the source ; stream idle indefinately before disconnecting. The default is 30. AutoDumpSourceTime=30
; ContentDir specifies the directory location on disk of where to stream ; on-demand content from. Subdirectories are supported as of DNAS 1.8.2. ; Default is ./content, meaning a directory named content in the same directory ; as where sc_serv was invoked from. ; ContentDir=./content
; IntroFile can specify a mp3 file that will be streamed to listeners right ; when they connect before they hear the live stream. ; Note that the intro file MUST be the same samplerate/channels as the ; live stream in order for this to work properly. Although bitrate CAN ; vary, you can use '%d' to specify the bitrate in the filename ; (i.e. C:\intro%d.mp3 would be C:\intro64.mp3 if you are casting at 64kbps). ; The default is no IntroFile ; IntroFile=c:\intro%d.mp3
; BackupFile can specify a mp3 file that will be streamed to listeners over ; and over again when the source stream disconnects. AutoDumpUsers must be ; 0 to use this feature. When the source stream reconnects, the listeners ; are rejoined into the live broadcast. ; Note that the backup file MUST be the same samplerate/channels as the ; live stream in order for this to work properly. Although bitrate CAN ; vary, you can use '%d' to specify the bitrate in the filename ; (i.e. C:\backup%d.mp3 would be C:\backup32.mp3 if you are casting at 32kbps). ; The default is no BackupFile ; BackupFile=C:\intro%d.mp3
; TitleFormat specifies a format string for what title is sent to the listener. ; For example, a string of 'Justin Radio' forces the title 'Justin Radio' even ; when the source changes the title. You can use up to one '%s' in the string ; which lets you contain the title from the source. For example, if your ; TitleFormat is 'Justin Radio: %s', and the source plug-in's title is ; 'Billy plays the blues', then the net title is ; 'Justin Radio: Billy plays the blues'. Note: only works on non-relay servers. ; The default is no format string. TitleFormat=hoho %s
; URLFormat specifies a format string for what url is sent to the listener. ; Behaves like TitleFormat (see above). ; The default is no format string. ; URLFormat=http://www.server.com/redirect.cgi?url=%s
; PublicServer can be always, never, or default (the default, heh) ; Any setting other than default will override the public status ; of the source plug-in or of a SHOUTcast server that is being relayed. PublicServer=default
; AllowRelay determines whether or not other SHOUTcast servers will be ; permitted to relay this server. The default is Yes. AllowRelay=Yes
; AllowPublicRelay, when set to No, will tell any relaying servers not ; to list the server in the SHOUTcast directory (non-public), provided ; the relaying server's Public flag is set to default. The default is ; Yes. AllowPublicRelay=Yes
; MetaInterval specifies how often, in bytes, metadata sent. ; You should really leave this at the default of 8192, but the option is ; provided anyway. MetaInterval=32768
; ***************************** ; Access Control ; *****************************
; ListenerTimer is a value in minutes of maximum permitted time for ; a connected listener. If someone is connected for longer than this ; amount of time, in minutes, they are disconnected. When undefined, ; there is no limit defined. Default is undefined. ; ListenerTimer=600
; BanFile is the text file sc_serv reads and writes to/from ; for the list of clients prohibited to connect to this ; server. It's automatically generated via the web ; interface. ; BanFile=sc_serv.ban
; RipFile is the text file sc_serv reads and writes to/from ; for the list of client IPs which are *ALWAYS* permitted ; to connect to this server (useful for relay servers). ; This file is automatically generated via the web ; interface. Note that if your server is FULL, and someone ; from a Reserved IP connects, the DNAS will force the person ; listening for the longest time off to make room for the new ; connection. ; RipFile=sc_serv.rip
; RIPOnly, when set to Yes, will only allow IP addresses listed in the Reserved ; IP list to connect and relay. All other connections for listening will be denied. ; This is really only useful for servers whose sole purpose is to provide the ; primary feed to all public relays. Setting this value to Yes also forces the ; server into Private mode, since listing this server in the directory would ; be pointless. Default is No. ; RIPOnly=No
; ***************************** ; Extended Logging ; *****************************
; The old features previously at this location, HistoryLog and CurrentLog, are ; no longer used and succeded by W3C Logging and XML, respectively.
; *************************** ; Mass Configuration ; ***************************
; Unique: assigns a variable name for use in any config item which points to a ; file. Useful for servers running lots of SHOUTcast servers that have similar ; configuration parameters, excepting logfile names, banfile names, etc. Any ; parameter that takes a pathname can include the character $, which will ; substitute $ for the variable assigned here. Keep in mind that the unique ; variable can only be used after it is defined, so don't try to use a unique ; variable substitution in a path before you define it. For example, you ; could set: ; Unique=my_server ; and then define Log=/usr/local/shoutcast/$.log in an included configuration ; file. Default is Unique=$, so that by default any file with $ in the name ; won't substitute anything at all.
; Include: instructs the sc_serv to read from the named configuration file, ; *at the point of insertion of the Include statement*, and process as though ; the included file was part of itself. Note that all configuration parameters ; in the DNAS config file are processed first to last, so if an item is defined ; twice in a configuration, the last item to process will be the one that takes ; effect. For this reason, it's usually a good idea to use the Includes first ; in a config file. ; example: ; Include=/usr/local/shoutcast/common.conf ; Default is not applicable.
; ***************************** ; Tweaks ; ***************************** ; ; DON'T MESS WITH THIS STUFF UNLESS YOU REALLY KNOW WHAT YOU'RE DOING. ; DON'T COMPLAIN TO US IF YOU MESS WITH IT AND THINGS BREAK. ; HAVE A NICE DAY.
; CpuCount is used to explicitly limit the DNAS to dominating a finite ; amount of processors in multiprocessor systems. By default, ; SHOUTcast creates one thread for every processor it detects in the ; host system, and assigns listeners equally across all the threads. ; In the event SHOUTcast doesn't correctly determine the number of ; CPUs in your host, or if you for whatever reason want to force ; the DNAS to not use other processors, you can say so here. ; Default behavior is to use as many processors as the DNAS detects on ; your system. ; CpuCount=1
; Sleep defines the granularity of the client threads for sending data. ; DNAS 1.7.0, per client thread, will send up to 1,024 bytes of data ; per socket (or less depending on the window available), and then ; sleep for the provided duration before repeating the whole process. ; Note that making this value smaller will vastly increase CPU usage on ; your machine. Increasing reduces CPU, but increasing this value too far ; will cause skips. The value which seems most optimal for 128kbps ; streaming is 833 (833 microseconds per client poll) on our test labs. ; We wouldn't recommend setting it any lower than 100, or any higher than ; 1,024. If you have a slower machine, set this number lower to fix ; skips. ; Default value is 833. ; Sleep=833
; CleanXML strips some whitespace and linefeeds from XML output which ; confuses some (poorly written) XML parsers. If you get XML rendering errors, ; try turning this on. Default is No (off). ; CleanXML=No ; ; TAG RULES
|
sc_trans.conf ->
Примерен код | ; Sample sc_trans/0.35-j config file ; j.frankel 12/05/00 ; t.pepper 10/31/00 ; (relays not supported, yo) ; ; sc_trans operates in one of two modes, either reading mp3s off disk, decoding, ; re-encoding, and then broadcasting them, or relaying from a shoutcast server, ; transcoding to a lower bitrate, and broadcasting to a new server.
; sc_trans accepts the following signals: ; HUP - flush logfiles (close and reopen) -- will make console logging stop ; WINCH - jump to next song ; USR1 - reload playlist off disk (will not interrupt current playing stream) ; USR2 - toggle shuffle on/off ; TERM - normal sc_trans shutdown (clean)
; PlaylistFile (required EVEN IF RELAYING) - playlist file (to create, use ; find /path/to/mp3/directory -type f -name "*.mp3" > playlist_filename.lst PlaylistFile=/home/h7d8/radio/house.m3u
; ServerIP/ServerPort are the target server to send to ServerIP=localhost ServerPort=8000
; Password is the password on the sc_serv you're sending to. Password=blablabla
; StreamTitle/URL/Genre define the data that appears on the directory and in the ; stream info. StreamTitle=Radio StreamURL=http://shibudabudab.dab Genre=House
; Logfile optionally denotes a text file to log sc_trans to. a kill -HUP ; will force a close and re-open of this file (but will also cease logging to ; the console) LogFile=/home/h7d8/radio/sc_trans.log
; Shuffle the playlist Shuffle=1
; Bitrate/SampleRate/Channels recommended values: ; 8kbps 8000/11025/1 ; 16kbps 16000/11025/1 ; 24kbps 24000/22050/1 ; 32kbps 32000/22050/1 ; 64kbps mono 64000/44100/1 ; 64kbps stereo 64000/22050/2 ; 96kbps stereo 96000/44100/2 ; 128kbps stere0 128000/44100/2 Bitrate=96000 SampleRate=44100 Channels=2 ; Quality is from 1-10. 1 is best, 10 is fastest. Quality=1
; Mode=0 for none, 1 for 100/100->100/0, 2 for 0/100->100/0 CrossfadeMode=1 ; Length is ms. CrossfadeLength=8000
UseID3=0
; Public determines whether or not this station will show up in the directory Public=1
; Put stuff here for user interaction (AOL IM, ICQ, IRC) AIM= ICQ= IRC=
|
Мисля си дали проблема не е в това ,че са на една машина и неможе да се нагласят в локалхост.Понеже като пусна сървър-а с моя DSP-plugin се закачам т.е от *.2.100 към сървър-а *.2.1.От там всеки който се закачи снифи от моя плейлист на winamp-a.Когато обаче пробвам с sc_trans нещо се омацва.Почти съм обеден ,че причината за това е:Примерен код | <08/28/08@18:48:41> [CONFIG] WARNING: No InputSamplerate defined, assuming 44100! <08/28/08@18:48:41> [CONFIG] WARNING: No InputChannels defined, assuming 2! <08/28/08@18:48:41> Warning: input file samplerate is -1208237319 Hz, must be 44100! | А и категорично проблема излиза ,че е от sc_trans т.е не се закача изобщо към сървър-а.Примерен код | <08/31/08@01:47:18> [STREAM] Creating stream socket <08/31/08@01:50:27> [STREAM] Error connecting to stream host [waiting 10s] <08/31/08@01:50:37> [STREAM] Creating stream socket <08/31/08@01:53:46> [STREAM] Error connecting to stream host [waiting 10s] <08/31/08@01:53:56> [STREAM] Creating stream socket | което ме свежда до мисълта ,че проблема е по-сериозен.Портове ,хостове ,firewall.Даже nmap ми отказва.
Примерен код | nmap 127.0.0.1
Starting Nmap 4.11 ( http://www.insecure.org/nmap/ ) at 2008-08-31 03:09 EDT Note: Host seems down. If it is really up, but blocking our ping probes, try -P0 Nmap finished: 1 IP address (0 hosts up) scanned in 0.284 seconds
|
->
Примерен код | nmap 192.168.2.100
Starting Nmap 4.11 ( http://www.insecure.org/nmap/ ) at 2008-08-31 03:09 EDT Interesting ports on 192.168.2.100: Not shown: 1675 closed ports PORT STATE SERVICE 80/tcp open http 135/tcp open msrpc 139/tcp open netbios-ssn 443/tcp open https 445/tcp open microsoft-ds MAC Address: 00:08:C7:2B:D1:01 (Compaq Computer)
Nmap finished: 1 IP address (1 host up) scanned in 1.527 seconds
|
Титла: Shoutcast
Публикувано от: h7d8 в Sep 01, 2008, 01:56
Реших си проблема.
Титла: Shoutcast
Публикувано от: bulg в Sep 01, 2008, 02:05
Kak?
Титла: Shoutcast
Публикувано от: h7d8 в Sep 03, 2008, 16:35
Цитат (bulg @ Сеп. 01 2008,05:05) | Kak? |
Проблем с loopback.. уш работи ,а всъщност неработи.ifiup ifdown ifup ifdown reboot и тръгна.
Титла: Shoutcast
Публикувано от: h7d8 в Sep 16, 2008, 20:08
Искам да махна Current title: от Info Box-a понеже е гадно потребителите да виждат коя песен върви в момента,ако някой го е махал да пише.Аз поне неможах да го махна от там.
|