ооооп обарках малко нештата


_XSERVTransSocketOpenCOTSServer: Unable to open socket for inet6
_XSERVTransOpen: transport open failed for inet6/Darkstar:0
_XSERVTransMakeAllCOTSServerListeners: failed to open listener for inet6

X Window System Version 6.8.2
Release Date: 9 February 2005
X Protocol Version 11, Revision 0, Release 6.8.2
Build Operating System: Linux 2.6.13 i686 [ELF]
Current Operating System: Linux Darkstar 2.4.31 #6 Sun Jun 5 19:04:47 PDT 2005 i686
Build Date: 11 September 2005
   Before reporting problems, check http://wiki.X.Org
   to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
   (++) from command line, (!!'> notice, (II) informational,
   (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sat Oct  8 12:59:45 2005
(==) Using config file: "/etc/X11/xorg.conf"
Parse warning on line 33 of section Keyboard in file /etc/X11/xorg.conf
   Ignoring obsolete keyword "LeftAlt".
Parse error on line 33 of section Keyboard in file /etc/X11/xorg.conf
   "Meta" is not a valid keyword in this section.
(EE) Problem parsing the config file
(EE) Error parsing the config file

Fatal server error:
no screens found

Please consult the The X.Org Foundation support
    at http://wiki.X.Org
 for help.
Please also check the log file at "/var/log/Xorg.0.log" for additional information.



това са грешките от xorg.conf

 '>

zdr sorry закаснелия отговор но lan картата се скапа и нямах нет е след малко почистване трагна '> относно лилото ами не нямаше как да разбера каква грешка дава тъи като го пусках директно от инсталацията на slack-a и ништо не изписа (: но но взех lilo.conf от knoppix-a ште публикувам него и дано някои даде акал как да го дооправя  '>  иначе в момента ботвам от диска на slack-a s bare.i root=/dev/hdb6 noinitrd ro

ето го и lilo.conf






# /etc/lilo.conf - See: `lilo(' and `lilo.conf(5)',
# ---------------       `install-mbr(', `/usr/share/doc/lilo/',
#                       and `/usr/share/doc/mbr/'.

# Remove this line when you are done configuring. -KK
"! Please edit /etc/lilo.conf before running lilo!"

# +---------------------------------------------------------------+
# |                        !! Reminder !!                         |
# |                                                               |
# | Don't forget to run `lilo' after you make changes to this     |
# | conffile, `/boot/bootmess.txt', or install a new kernel.  The |
# | computer will most likely fail to boot if a kernel-image      |
# | post-install script or you don't remember to run `lilo'.      |
# |                                                               |
# +---------------------------------------------------------------+

# Support LBA for large hard disks.
#
#lba32

# Specifies the boot device.  This is where Lilo installs its boot
# block.  It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.

boot=/dev/hdb6

# Specifies the device that should be mounted as root. (`/''>
#

# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller.  Using `compact' is especially recommended when
# booting from a floppy disk.  It is disabled here by default
# because it doesn't always work.
#
# compact

# Installs the specified file as the new boot sector
#
install=/boot/boot-menu.b
backup=/dev/null

# Specifies the location of the map file
#
map=/boot/map

# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration.  If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well.  Please RTFM `install-mbr('.
#
# password=tatercounter2000

# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
# delay=20
timeout=5

# You can put a customized boot message up if you like.  If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress.  `single-key' goes with the `alias' lines in the
# `image' configurations below.  eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
# message=/boot/bootmess.txt
#   prompt
#   single-key
#   delay=100
#   timeout=100

# Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>)
#
# vga=ask
# vga=9
#
vga=normal

# Kernel command line options that apply to all installed images go
# here.  See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""

# Boot up Linux by default.
#
default=Linux

image=/vmlinuz
   root=/dev/hdb6
   label=Slackwere-Linux
   read-write
#   restricted
#   alias=1


#image=/vmlinuz.old
#   label=Linux-OLD
#   read-only
#   optional
#   restricted
#   alias=2


# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.

other=/dev/hdb1
  label=Buzaata
  restricted
  alias=3


съм променял ништо по него харда ми hdb

os slackwere 10.2
videocard asus ati radeon 9550ge
но не я разпознава малко е старичак тоя knoppix '>


a сега относно другата болежка
 

не мога да си конфигурирам X-a естествено пробвах като копирах xorg.conf от knoppix но уви не става както казах по горе не разпознава видеокартата а и клавиатурата съ;то (:

ето грешките които дава:


# /etc/lilo.conf - See: `lilo(' and `lilo.conf(5)',
# ---------------       `install-mbr(', `/usr/share/doc/lilo/',
#                       and `/usr/share/doc/mbr/'.

# Remove this line when you are done configuring. -KK
"! Please edit /etc/lilo.conf before running lilo!"

# +---------------------------------------------------------------+
# |                        !! Reminder !!                         |
# |                                                               |
# | Don't forget to run `lilo' after you make changes to this     |
# | conffile, `/boot/bootmess.txt', or install a new kernel.  The |
# | computer will most likely fail to boot if a kernel-image      |
# | post-install script or you don't remember to run `lilo'.      |
# |                                                               |
# +---------------------------------------------------------------+

# Support LBA for large hard disks.
#
#lba32

# Specifies the boot device.  This is where Lilo installs its boot
# block.  It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.

boot=/dev/hdb6

# Specifies the device that should be mounted as root. (`/''>
#

# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller.  Using `compact' is especially recommended when
# booting from a floppy disk.  It is disabled here by default
# because it doesn't always work.
#
# compact

# Installs the specified file as the new boot sector
#
install=/boot/boot-menu.b
backup=/dev/null

# Specifies the location of the map file
#
map=/boot/map

# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration.  If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well.  Please RTFM `install-mbr('.
#
# password=tatercounter2000

# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
# delay=20
timeout=5

# You can put a customized boot message up if you like.  If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress.  `single-key' goes with the `alias' lines in the
# `image' configurations below.  eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
# message=/boot/bootmess.txt
#   prompt
#   single-key
#   delay=100
#   timeout=100

# Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>)
#
# vga=ask
# vga=9
#
vga=normal

# Kernel command line options that apply to all installed images go
# here.  See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""

# Boot up Linux by default.
#
default=Linux

image=/vmlinuz
   root=/dev/hdb6
   label=Slackwere-Linux
   read-write
#   restricted
#   alias=1


#image=/vmlinuz.old
#   label=Linux-OLD
#   read-only
#   optional
#   restricted
#   alias=2


# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.

other=/dev/hdb1
  label=Buzaata
  restricted
  alias=3

 

 


 '>


post на xorg.conf както е от knoppix

Section "Files"
        RgbPath      "/usr/X11R6/lib/X11/rgb"
        FontPath     "/usr/X11R6/lib/X11/fonts/misc:unscaled"
        FontPath     "/usr/X11R6/lib/X11/fonts/misc"
        FontPath     "/usr/X11R6/lib/X11/fonts/75dpi:unscaled"
        FontPath     "/usr/X11R6/lib/X11/fonts/75dpi"
        FontPath     "/usr/X11R6/lib/X11/fonts/100dpi:unscaled"
        FontPath     "/usr/X11R6/lib/X11/fonts/100dpi"
        FontPath     "/usr/X11R6/lib/X11/fonts/Speedo"
        FontPath     "/usr/X11R6/lib/X11/fonts/PEX"
# Additional fonts: Locale, Gimp, TTF...
        FontPath     "/usr/X11R6/lib/X11/fonts/cyrillic"
#        FontPath     "/usr/X11R6/lib/X11/fonts/latin2/75dpi"
#        FontPath     "/usr/X11R6/lib/X11/fonts/latin2/100dpi"
# True type and type1 fonts are also handled via xftlib, see /etc/X11/XftConfig!
   FontPath     "/usr/X11R6/lib/X11/fonts/Type1"
        FontPath     "/usr/share/fonts/ttf/western"
        FontPath     "/usr/share/fonts/ttf/decoratives"
   FontPath     "/usr/share/fonts/truetype"
        FontPath     "/usr/share/fonts/truetype/openoffice"
        FontPath     "/usr/share/fonts/truetype/ttf-bitstream-vera"
   FontPath     "/usr/share/fonts/latex-ttf-fonts"
        FontPath     "/usr/X11R6/lib/X11/fonts/defoma/CID"
        FontPath     "/usr/X11R6/lib/X11/fonts/defoma/TrueType"
EndSection

Section "ServerFlags"
EndSection

Section "Keyboard"
   Protocol    "Standard"
   AutoRepeat  500 5
   LeftAlt        Meta
   RightAlt        Meta
   ScrollLock      Compose
   RightCtl        Control
# This is just the default keymap for X.
# May be changed with the KDE international keyboard tool.
   XkbModel    "pc105"
   XkbLayout "us"

#   XkbOptions  "ctrl:swapcaps"
#   XkbKeycodes     "xfree86"
#   XkbTypes        "default"
#   XkbCompat       "default"
#   XkbSymbols      "us(pc101)"
#   XkbGeometry     "pc"
#   XkbRules        "xfree86"
#   XkbModel        "pc101"
#   XkbLayout "us"
EndSection

Section "Pointer"
    Protocol    "PS/2"
    Device      "/dev/mouse"
    Emulate3Buttons
    Emulate3Timeout    70
EndSection

# Auto-generated by mkxf86config

Section "Monitor"
   Identifier   "Monitor0"
   VendorName   "DEL"
   ModelName   "DEL5155"
   HorizSync 30 - 85 # DDC-probed
   VertRefresh 50 - 120 # DDC-probed
   # These are the DDC-probed settings reported by your monitor.
   # 1600x1200, 65.0Hz; hfreq=81.25, vfreq=65.00
   ModeLine "1600x1200"   175.50 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync
   # 1024x768, 85.0Hz; hfreq=68.68, vfreq=85.00
   ModeLine "1024x768"    94.50 1024 1072 1168 1376  768  769  772  808 +hsync +vsync
   # 1024x768, 75.0Hz; hfreq=60.02, vfreq=75.03
   ModeLine "1024x768"    78.75 1024 1040 1136 1312  768  769  772  800 +hsync +vsync
   # 800x600, 85.0Hz; hfreq=53.67, vfreq=85.06
   ModeLine "800x600"    56.25  800  832  896 1048  600  601  604  631 +hsync +vsync
   # 800x600, 75.0Hz; hfreq=46.88, vfreq=75.00
   ModeLine "800x600"    49.50  800  816  896 1056  600  601  604  625 +hsync +vsync
   # 800x600, 72.0Hz; hfreq=48.08, vfreq=72.19
   ModeLine "800x600"    50.00  800  856  976 1040  600  637  643  666 +hsync +vsync
   # 800x600, 60.0Hz; hfreq=37.88, vfreq=60.32
   ModeLine "800x600"    40.00  800  840  968 1056  600  601  605  628 +hsync +vsync
   # 640x480, 85.0Hz; hfreq=43.27, vfreq=85.01
   ModeLine "640x480"    36.00  640  696  752  832  480  481  484  509 -hsync -vsync
   # 640x480, 75.0Hz; hfreq=37.50, vfreq=75.00
   ModeLine "640x480"    31.50  640  656  720  840  480  481  484  500 -hsync -vsync
   # 640x480, 60.0Hz; hfreq=31.47, vfreq=59.94
   ModeLine "640x480"    25.17  640  648  744  784  480  482  484  509 -hsync -vsync
   # Extended modelines with GTF timings
   # 640x480 @ 100.00 Hz (GTF) hsync: 50.90 kHz; pclk: 43.16 MHz
   ModeLine "640x480"  43.16  640 680 744 848  480 481 484 509  -HSync +Vsync
   # 768x576 @ 60.00 Hz (GTF) hsync: 35.82 kHz; pclk: 34.96 MHz
   ModeLine "768x576"  34.96  768 792 872 976  576 577 580 597  -HSync +Vsync
   # 768x576 @ 72.00 Hz (GTF) hsync: 43.27 kHz; pclk: 42.93 MHz
   ModeLine "768x576"  42.93  768 800 880 992  576 577 580 601  -HSync +Vsync
   # 768x576 @ 75.00 Hz (GTF) hsync: 45.15 kHz; pclk: 45.51 MHz
   ModeLine "768x576"  45.51  768 808 888 1008  576 577 580 602  -HSync +Vsync
   # 768x576 @ 85.00 Hz (GTF) hsync: 51.42 kHz; pclk: 51.84 MHz
   ModeLine "768x576"  51.84  768 808 888 1008  576 577 580 605  -HSync +Vsync
   # 768x576 @ 100.00 Hz (GTF) hsync: 61.10 kHz; pclk: 62.57 MHz
   ModeLine "768x576"  62.57  768 816 896 1024  576 577 580 611  -HSync +Vsync
   # 800x600 @ 100.00 Hz (GTF) hsync: 63.60 kHz; pclk: 68.18 MHz
   ModeLine "800x600"  68.18  800 848 936 1072  600 601 604 636  -HSync +Vsync
   # 1024x768 @ 100.00 Hz (GTF) hsync: 81.40 kHz; pclk: 113.31 MHz
   ModeLine "1024x768"  113.31  1024 1096 1208 1392  768 769 772 814  -HSync +Vsync
   # 1152x864 @ 60.00 Hz (GTF) hsync: 53.70 kHz; pclk: 81.62 MHz
   ModeLine "1152x864"  81.62  1152 1216 1336 1520  864 865 868 895  -HSync +Vsync
   # 1152x864 @ 85.00 Hz (GTF) hsync: 77.10 kHz; pclk: 119.65 MHz
   ModeLine "1152x864"  119.65  1152 1224 1352 1552  864 865 868 907  -HSync +Vsync
   # 1152x864 @ 100.00 Hz (GTF) hsync: 91.50 kHz; pclk: 143.47 MHz
   ModeLine "1152x864"  143.47  1152 1232 1360 1568  864 865 868 915  -HSync +Vsync
   # 1280x960 @ 72.00 Hz (GTF) hsync: 72.07 kHz; pclk: 124.54 MHz
   ModeLine "1280x960"  124.54  1280 1368 1504 1728  960 961 964 1001  -HSync +Vsync
   # 1280x960 @ 75.00 Hz (GTF) hsync: 75.15 kHz; pclk: 129.86 MHz
   ModeLine "1280x960"  129.86  1280 1368 1504 1728  960 961 964 1002  -HSync +Vsync
   # 1280x960 @ 100.00 Hz (GTF) hsync: 101.70 kHz; pclk: 178.99 MHz
   ModeLine "1280x960"  178.99  1280 1376 1520 1760  960 961 964 1017  -HSync +Vsync
   # 1280x1024 @ 100.00 Hz (GTF) hsync: 108.50 kHz; pclk: 190.96 MHz
   ModeLine "1280x1024"  190.96  1280 1376 1520 1760  1024 1025 1028 1085  -HSync +Vsync
   # 1400x1050 @ 60.00 Hz (GTF) hsync: 65.22 kHz; pclk: 122.61 MHz
   ModeLine "1400x1050"  122.61  1400 1488 1640 1880  1050 1051 1054 1087  -HSync +Vsync
   # 1400x1050 @ 72.00 Hz (GTF) hsync: 78.77 kHz; pclk: 149.34 MHz
   ModeLine "1400x1050"  149.34  1400 1496 1648 1896  1050 1051 1054 1094  -HSync +Vsync
   # 1400x1050 @ 75.00 Hz (GTF) hsync: 82.20 kHz; pclk: 155.85 MHz
   ModeLine "1400x1050"  155.85  1400 1496 1648 1896  1050 1051 1054 1096  -HSync +Vsync
   # 1400x1050 @ 85.00 Hz (GTF) hsync: 93.76 kHz; pclk: 179.26 MHz
   ModeLine "1400x1050"  179.26  1400 1504 1656 1912  1050 1051 1054 1103  -HSync +Vsync
   # 1400x1050 @ 100.00 Hz (GTF) hsync: 111.20 kHz; pclk: 214.39 MHz
   ModeLine "1400x1050"  214.39  1400 1512 1664 1928  1050 1051 1054 1112  -HSync +Vsync
   # 1600x1200 @ 100.00 Hz (GTF) hsync: 127.10 kHz; pclk: 280.64 MHz
   ModeLine "1600x1200"  280.64  1600 1728 1904 2208  1200 1201 1204 1271  -HSync +Vsync
EndSection

Section "Device"
    Identifier    "My Video Card"
    VendorName    "Unknown"
    BoardName     "Unknown"
#     TextClockFreq  22.175
EndSection

Section "Device"
  Identifier    "fbdev"
  VendorName    "Unknown"
  BoardName     "Unknown"
EndSection


# Standard Server
Section "Screen"
    Driver      "svga"
    Device      "My Video Card"
    Monitor     "Monitor0"
    Subsection  "Display"
        Modes "1024x768" "800x600" "640x480"
        ViewPort 0 0
    EndSubsection
EndSection

# Accel. Server(s)
Section "Screen"
    Driver      "accel"
    Device      "My Video Card"
    Monitor     "Monitor0"
    Subsection  "Display"
        Modes "1024x768" "800x600" "640x480"
        ViewPort 0 0
    EndSubsection
EndSection

# Fallback
Section "Screen"
    Driver      "vga16"
    Device      "My Video Card"
    Monitor     "Monitor0"
    Subsection  "Display"
        Modes "1024x768" "800x600" "640x480"
    EndSubsection
EndSection

Section "Screen"  
  Driver        "fbdev"
  Device        "fbdev"
  Monitor       "Monitor0"
  SubSection "Display"
    Depth       32
    Modes       "default"
  EndSubSection
  SubSection "Display"
    Depth       24
    Modes       "default"
  EndSubSection
  SubSection "Display"
    Depth       16
    Modes       "default"
  EndSubSection
  SubSection "Display"
    Depth       15
    Modes       "default"
  EndSubSection
  SubSection "Display"
    Depth       8
    Modes       "default"
  EndSubSection
EndSection



 '>


ето и резултатите от X -configure


Section "ServerLayout"
   Identifier     "X.org Configured"
   Screen      0  "Screen0" 0 0
   InputDevice    "Mouse0" "CorePointer"
   InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
   RgbPath      "/usr/X11R6/lib/X11/rgb"
   ModulePath   "/usr/X11R6/lib/modules"
   FontPath     "/usr/X11R6/lib/X11/fonts/misc/"
   FontPath     "/usr/X11R6/lib/X11/fonts/TTF/"
   FontPath     "/usr/X11R6/lib/X11/fonts/Type1/"
   FontPath     "/usr/X11R6/lib/X11/fonts/CID/"
   FontPath     "/usr/X11R6/lib/X11/fonts/75dpi/"
   FontPath     "/usr/X11R6/lib/X11/fonts/100dpi/"
EndSection

Section "Module"
   Load  "record"
   Load  "extmod"
   Load  "dbe"
   Load  "dri"
   Load  "glx"
   Load  "xtrap"
   Load  "freetype"
   Load  "type1"
EndSection

Section "InputDevice"
   Identifier  "Keyboard0"
   Driver      "kbd"
EndSection

Section "InputDevice"
   Identifier  "Mouse0"
   Driver      "mouse"
   Option       "Protocol" "auto"
   Option       "Device" "/dev/mouse"
EndSection

Section "Monitor"
   #DisplaySize     330   240   # mm
   Identifier   "Monitor0"
   VendorName   "DEL"
   ModelName    "DELL D1025TM"
   HorizSync    30.0 - 85.0
   VertRefresh  50.0 - 120.0
   Option       "DPMS"
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
        ### [arg]: arg optional
        #Option     "NoAccel"               # [<bool>]
        #Option     "SWcursor"              # [<bool>]
        #Option     "Dac6Bit"               # [<bool>]
        #Option     "Dac8Bit"               # [<bool>]
        #Option     "BusType"               # [<str>]
        #Option     "CPPIOMode"             # [<bool>]
        #Option     "CPusecTimeout"         # <i>
        #Option     "AGPMode"               # <i>
        #Option     "AGPFastWrite"          # [<bool>]
        #Option     "AGPSize"               # <i>
        #Option     "GARTSize"              # <i>
        #Option     "RingSize"              # <i>
        #Option     "BufferSize"            # <i>
        #Option     "EnableDepthMoves"      # [<bool>]
        #Option     "EnablePageFlip"        # [<bool>]
        #Option     "NoBackBuffer"          # [<bool>]
        #Option     "PanelOff"              # [<bool>]
        #Option     "DDCMode"               # [<bool>]
        #Option     "MonitorLayout"         # [<str>]
        #Option     "IgnoreEDID"            # [<bool>]
        #Option     "UseFBDev"              # [<bool>]
        #Option     "VideoKey"              # <i>
        #Option     "MergedFB"              # [<bool>]
        #Option     "CRT2HSync"             # [<str>]
        #Option     "CRT2VRefresh"          # [<str>]
        #Option     "CRT2Position"          # [<str>]
        #Option     "MetaModes"             # [<str>]
        #Option     "MergedDPI"             # [<str>]
        #Option     "NoMergedXinerama"      # [<bool>]
        #Option     "MergedXineramaCRT2IsScreen0"    # [<bool>]
        #Option     "DisplayPriority"       # [<str>]
        #Option     "PanelSize"             # [<str>]
        #Option     "ForceMinDotClock"      # <freq>
        #Option     "RenderAccel"           # [<bool>]
        #Option     "SubPixelOrder"         # [<str>]
        #Option     "ShowCache"             # [<bool>]
        #Option     "DynamicClocks"         # [<bool>]
   Identifier  "Card0"
   Driver      "ati"
   VendorName  "ATI Technologies Inc"
   BoardName   "RV350 AP [Radeon 9600]"
   BusID       "PCI:2:0:0"
EndSection

Section "Screen"
   Identifier "Screen0"
   Device     "Card0"
   Monitor    "Monitor0"
   SubSection "Display"
      Viewport   0 0
      Depth     1
   EndSubSection
   SubSection "Display"
      Viewport   0 0
      Depth     4
   EndSubSection
   SubSection "Display"
      Viewport   0 0
      Depth     8
   EndSubSection
   SubSection "Display"
      Viewport   0 0
      Depth     15
   EndSubSection
   SubSection "Display"
      Viewport   0 0
      Depth     16
   EndSubSection
   SubSection "Display"
      Viewport   0 0
      Depth     24
   EndSubSection
EndSection

помагаите че съм на голям зоррр с buzata  не се издаржа
'>

здр на всички и такам значи качих си slackwere 10.2 i и при инсталиране на lilo-to даде грешка някаква така и не можах да разбера каква е...както и да е '> lilo като че ли е наи малкия проблем съшто и X-a и него не можах да подкарам пробвах като копирах Xf86config oт knoppix но и по този начин не стана редактирах го таи като не идентифицираше видео картата но пак не стана даде грешка в section keyboard... и section screen начинаешт съм с linux с голямо желание и малки познания (: ако някои мойе да помогне щте със много благодарен един конфигуруран lilo.conf би ми дошал добре '> а относно X-a надявам се някои да ми каже как мога да конфигурирам пробвах с X -configure но без успех...monitor dell5155 video card ati raedeon 9550ge  
 
 '>

значи имам радеон 9550 ge някои има ли представа до каква
 степен може да се клокне мислиа че оптималния вариант е
238fps
 та интересува ме оптимална честота на ядрото и на паметта
благодаря предварително

със slack 10 sum imam kvirc-3.0.1 която си работи доста добре ,но има някои много дразнещи нещта с които не мога да се справя с double click варху nick които искам да отваря нищто не става все едно не съм натиснал нищто не се отваря нов диалогов прозорец
нищто...2.от настроиките съм сложил прозрачност но има blending и никаде не видях от каде мога да го махна прерових настроиките изцяло ,много глупави вапросчета но ще се радвам ако някои даде савет какво да правя 10x предварително   а за малко да забравя може ли някои да каже от каде мога да си сваля читави кодеци за xine че не ми отваря някои видео формати  '>
пробвах от linuxpackages.net но не стана нищто явно архива не беше в ред...

as nachinaesh slackwere user eto i ot kade idvat glupavite problemcheta s koito ne moga da se spravia.....

opitvah se da instaliram macromedia flashplayer za firefox

NOTE: Macromedia Flash Player requires two font packages
     to be installed, ttfonts and urw-fonts.

Press ENTER to continue...



NOTE: Please exit any browsers you may have running.

Press ENTER to continue...

Please enter the installation path of the Mozilla, Netscape,
or Opera browser (i.e., /usr/lib/mozilla): /usr/bin/firefox

WARNING: /usr/bin/firefox is not a directory.

Please enter the installation path of the Mozilla, Netscape,
or Opera browser (i.e., /usr/lib/mozilla): /usr/bin/netscape

WARNING: /usr/bin/netscape is not a directory.

Please enter the installation path of the Mozilla, Netscape,
or Opera browser (i.e., /usr/lib/mozilla): /usr/bin/mozilla

WARNING: /usr/bin/mozilla is not a directory.

Please enter the installation path of the Mozilla, Netscape,
or Opera browser (i.e., /usr/lib/mozilla):  

i otnovo v zadanena ulica (:    ot /usr/bin/firefox se startira firefox no directoriata mu e v /home/cain/Programs/fireFox/firefox-installer/xpi/bin  i stova probvah vse sushtoto ....  

някои може ли да ми каже как мога да си инсталирам и пусна битторент на slack 10 че ми е пълна мъгла доста нешта опитах и ништо не стана (: свалил съм и py.gtk-2-5-3 за торента които може да помогне  

as nachinaesh slackwere user eto i ot kade idvat glupavite problemcheta s koito ne moga da se spravia.....

opitvah se da instaliram macromedia flashplayer za firefox

NOTE: Macromedia Flash Player requires two font packages
     to be installed, ttfonts and urw-fonts.

Press ENTER to continue...



NOTE: Please exit any browsers you may have running.

Press ENTER to continue...

Please enter the installation path of the Mozilla, Netscape,
or Opera browser (i.e., /usr/lib/mozilla): /usr/bin/firefox

WARNING: /usr/bin/firefox is not a directory.

Please enter the installation path of the Mozilla, Netscape,
or Opera browser (i.e., /usr/lib/mozilla): /usr/bin/netscape

WARNING: /usr/bin/netscape is not a directory.

Please enter the installation path of the Mozilla, Netscape,
or Opera browser (i.e., /usr/lib/mozilla): /usr/bin/mozilla

WARNING: /usr/bin/mozilla is not a directory.

Please enter the installation path of the Mozilla, Netscape,
or Opera browser (i.e., /usr/lib/mozilla):  

i otnovo v zadanena ulica (:    ot /usr/bin/firefox se startira firefox no directoriata mu e v /home/cain/Programs/fireFox/firefox-installer/xpi/bin  i stova probvah vse sushtoto ....