Автор Тема: Scrol na mishkata & Slackware 10.1  (Прочетена 2601 пъти)

stilldark

  • Участници
  • ***
  • Публикации: 8
    • Профил
Scrol na mishkata & Slackware 10.1
« -: Mar 15, 2005, 19:02 »
Значи прочетох темите за скрола на мишката

 В /etc/X11/XF86Config
Section "InputDevice"
промени :

Option "Protocol"     "imps/2"
Option "Device"      "/dev/psaux"
Option "Buttons"    "5"
Option "ZAxisMapping"    "4 5"

Само че при мен го няма този конфиг '<img'>

Едит:
Не знам дали е важно но модела на мишката е Лоджитек МХ700
/etc/X11/XF86Config '<img'>
Активен

dope_hat

  • Напреднали
  • *****
  • Публикации: 131
    • Профил
    • WWW
Scrol na mishkata & Slackware 10.1
« Отговор #1 -: Mar 15, 2005, 19:13 »
Добави направо тази секция в конфигурационния файл и ще проработи
Примерен код

Section "InputDevice"
Identifier  "Mouse0"
Driver      "mouse"
Option      "Protocol" "auto"
Option      "Device" "/dev/mouse"
Option      "ZaxisMapping" "4 5"
Option      "Buttons" "5"
EndSection


Успех,
Активен

FreeBSD:The Power To Serve

nifelheim

  • Напреднали
  • *****
  • Публикации: 328
  • Distribution: Kubuntu
  • Window Manager: KDE
    • Профил
    • WWW
Scrol na mishkata & Slackware 10.1
« Отговор #2 -: Mar 15, 2005, 19:25 »
Конфиг файла вече се нарича xorg.conf, останалото е същото както го пише във форумите.
Активен

Оптимистът изучава английски език. Песимистът - китайски. А реалистът - автомат Калашников.

stilldark

  • Участници
  • ***
  • Публикации: 8
    • Профил
Scrol na mishkata & Slackware 10.1
« Отговор #3 -: Mar 15, 2005, 19:31 »
Мерси промених го в този вид:

Section "InputDevice"

# Identifier and driver

    Identifier "Mouse1"
    Driver "mouse"
    Option "Protocol"    "IMPS/2"
    Option "Device"      "/dev/psaux"

# Mouse-speed setting for PS/2 mouse.

#    Option "Resolution"   "256"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

#    Option "Protocol"   "Xqueue"

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

#    Option "BaudRate"   "9600"
#    Option "SampleRate" "150"

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

#    Option "Emulate3Buttons"    "yes"
#    Option "Emulate3Timeout"    "50"

# ChordMiddle is an option for some 3-button Logitech mice

#    Option "ChordMiddle"
     Option "ZAxisMapping"     "4 5"
EndSection


Но пак не става къде греша?
Активен

dope_hat

  • Напреднали
  • *****
  • Публикации: 131
    • Профил
    • WWW
Scrol na mishkata & Slackware 10.1
« Отговор #4 -: Mar 15, 2005, 19:43 »
Предполагам си тест-вал и mouseconfig, но така като гледам ме навежда на мисълта, че грешката е в :
Option "Device" "/dev/psaux"
Промени го на :
Option "Device" "/dev/mouse"
и кажи дали така не се получава '<img'>
Активен

FreeBSD:The Power To Serve

stilldark

  • Участници
  • ***
  • Публикации: 8
    • Профил
Scrol na mishkata & Slackware 10.1
« Отговор #5 -: Mar 15, 2005, 20:38 »
Значи сега го преведох в този вид:
Section "InputDevice"

# Identifier and driver

    Identifier "Mouse1"
    Driver "mouse"
    Option "Protocol"    "auto"
    Option "Device"      "/dev/mouse"

# Mouse-speed setting for PS/2 mouse.

#    Option "Resolution" "256"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

#    Option "Protocol" "Xqueue"

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

#    Option "BaudRate" "9600"
#    Option "SampleRate" "150"

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

#    Option "Emulate3Buttons"    "yes"
#    Option "Emulate3Timeout"    "50"

# ChordMiddle is an option for some 3-button Logitech mice

#    Option "ChordMiddle"
     Option "ZAxisMapping"     "4 5"
EndSection
Тествам като рестартирам Х-а и пак нямам Скрол '<img'>
Активен

Drakula

  • Напреднали
  • *****
  • Публикации: 319
  • Distribution: Gentoo
  • Window Manager: KDE 4
    • Профил
Scrol na mishkata & Slackware 10.1
« Отговор #6 -: Mar 15, 2005, 23:09 »
Ами аз ползвам Slackware 10.1 и скролът ми е на 6. Ето секцията за мишка в моя xorg.conf:
Примерен код

Section "InputDevice"

# Identifier and driver

    Identifier   "Mouse1"
    Driver   "mouse"
    Option "Protocol"    "IMPS/2"
    Option "Device"      "/dev/mouse"

    Option "Emulate3Buttons"
     Option "ZAxisMapping" "4 5"
EndSection
Активен

stilldark

  • Участници
  • ***
  • Публикации: 8
    • Профил
Scrol na mishkata & Slackware 10.1
« Отговор #7 -: Mar 19, 2005, 09:12 »
Пак не стана '<img'> ето го целия конфиг:

# File generated by xorgconfig.

#
# Copyright 2004 The X.Org Foundation
#
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
#
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
#
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
# The X.Org Foundation BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
#
# Except as contained in this notice, the name of The X.Org Foundation shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from
# The X.Org Foundation.
#

# **********************************************************************
# Refer to the xorg.conf(5x) man page for details about the format of
# this file.
# **********************************************************************

# **********************************************************************
# Module section -- this  section  is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"

# This loads the DBE extension module.

    Load        "dbe"     # Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
    SubSection  "extmod"
      Option    "omit xfree86-dga"   # don't initialise the DGA extension
    EndSubSection

# This loads the font modules
    Load        "type1"
#    Load        "speedo"
    Load        "freetype"
#    Load        "xtt"

# This loads the GLX module
    Load       "glx"
# This loads the DRI module
#    Load       "dri"

EndSection

# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.

    RgbPath   "/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#
#


# The module search path.  The default path is shown here.

#    ModulePath "/usr/X11R6/lib/modules"

    FontPath    "/usr/X11R6/lib/X11/fonts/misc"
    FontPath    "/usr/X11R6/lib/X11/fonts/TTF"
    FontPath    "/usr/X11R6/lib/X11/fonts/Type1"
    FontPath    "/usr/X11R6/lib/X11/fonts/CID"
    FontPath    "/usr/X11R6/lib/X11/fonts/75dpi"
    FontPath    "/usr/X11R6/lib/X11/fonts/100dpi"
    FontPath    "/usr/X11R6/lib/X11/fonts/local"
    FontPath    "/usr/X11R6/lib/X11/fonts/Speedo"
    FontPath    "/usr/X11R6/lib/X11/fonts/cyrillic"
    FontPath    "/usr/local/share/fonts"
    FontPath    "/usr/share/fonts"
    FontPath    "/usr/X11R6/lib/X11/fonts"
EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is
# received.  This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

#    Option "NoTrapSignals"

# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12).  This allows clients to receive these key
# events.

#    Option "DontVTSwitch"

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.

#    Option "DontZap"

# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences.  This allows clients to receive these key events.

#    Option "Dont Zoom"

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

#    Option "DisableVidModeExtension"

# Uncomment this to enable the use of a non-local xvidtune client.

#    Option "AllowNonLocalXvidtune"

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.

#    Option "DisableModInDev"

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

#    Option "AllowNonLocalModInDev"

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************

Section "InputDevice"

    Identifier   "Keyboard1"
    Driver   "kbd"

# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.

#    Option     "Protocol"      "Xqueue"

    Option "AutoRepeat" "500 30"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
#    Option   "Xleds"      "1 2 3"

#    Option "LeftAlt"     "Meta"
#    Option "RightAlt"    "ModeShift"

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults).  For example, for a non-U.S.
# keyboard, you will probably want to use:
#    Option "XkbModel"    "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
#    Option "XkbModel"    "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#    Option "XkbLayout"   "de"
# or:
#    Option "XkbLayout"   "de"
#    Option "XkbVariant"  "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
#    Option "XkbOptions"  "ctrl:swapcaps"

# These are the default XKB settings for Xorg
#    Option "XkbRules"    "xorg"
#    Option "XkbModel"    "pc101"
#    Option "XkbLayout"   "us"
#    Option "XkbVariant"  ""
#    Option "XkbOptions"  ""

#    Option "XkbDisable"

    Option "XkbRules"   "xorg"
    Option "XkbModel"   "pc101"
    Option "XkbLayout"   "us"

EndSection


# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************

Section "InputDevice"

# Identifier and driver

    Identifier "Mouse1"
    Driver "mouse"
    Option "Protocol"    "IMPS/2"
    Option "Device"      "/dev/mouse"

    Option "Emulate3Buttons"
     Option "ZAxisMapping" "4 5"
EndSection


# **********************************************************************
# Other input device sections
# this is optional and is required only if you
# are using extended input devices.  This is for example only.  Refer
# to the xorg.conf man page for a description of the options.
# **********************************************************************
#
#
# Section "InputDevice"
#    Identifier "spaceball"
#    Driver     "magellan"
#    Option     "Device"        "/dev/cua0"
# EndSection
#
# Section "InputDevice"
#    Identifier "spaceball2"
#    Driver     "spaceorb"
#    Option     "Device"        "/dev/cua0"
# EndSection
#
# Section "InputDevice"
#    Identifier "touchscreen0"
#    Driver     "microtouch"
#    Option     "Device"        "/dev/ttyS0"
#    Option     "MinX"          "1412"
#    Option     "MaxX"          "15184"
#    Option     "MinY"          "15372"
#    Option     "MaxY"          "1230"
#    Option     "ScreenNumber"  "0"
#    Option     "ReportingMode" "Scaled"
#    Option     "ButtonNumber"  "1"
#    Option     "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
#    Identifier "touchscreen1"
#    Driver     "elo2300"
#    Option     "Device"        "/dev/ttyS0"
#    Option     "MinX"          "231"
#    Option     "MaxX"          "3868"
#    Option     "MinY"          "3858"
#    Option     "MaxY"          "272"
#    Option     "ScreenNumber"  "0"
#    Option     "ReportingMode" "Scaled"
#    Option     "ButtonThreshold"       "17"
#    Option     "ButtonNumber"  "1"
#    Option     "SendCoreEvents"
# EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

    Identifier  "My Monitor"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    HorizSync   31.5 - 57.0

#    HorizSync   30-64         # multisync
#    HorizSync   31.5, 35.2    # multiple fixed sync frequencies
#    HorizSync   15-25, 30-50  # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    VertRefresh 50-100

EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
    Identifier   "Standard VGA"
    VendorName   "Unknown"
    BoardName   "Unknown"

# The chipset line is optional in most cases.  It can be used to override
# the driver's chipset detection, and should not normally be specified.

#    Chipset   "generic"

# The Driver line must be present.  When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module.  Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.

    Driver     "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for.  When this line isn't present, a device
# section can only match up with the primary video device.  For PCI
# devices a line like the following could be used.  This line should not
# normally be included unless there is more than one video device
# intalled.

#    BusID      "PCI:0:10':0'"

#    VideoRam   256

#    Clocks   25.2 28.3

EndSection

# Device configured by xorgconfig:

Section "Device"
    Identifier  "nv"
    Driver      "nv"
    #VideoRam    131072
    # Insert Clocks lines here if appropriate
EndSection


# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present.  Each describes
# the configuration of a single screen.  A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
    Identifier  "Screen 1"
    Device      "nv"
    Monitor     "My Monitor"
    DefaultDepth 24

    Subsection "Display"
        Depth       8
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       16
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       24
        Modes       "1280x1024"
        ViewPort    0 0
    EndSubsection
EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present.  Each describes
# the way multiple screens are organised.  A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option.  In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
    Identifier  "Simple Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens.  The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen.  In this example, screen 2 is located to the
# right of screen 1.

    Screen "Screen 1"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used.  Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

    InputDevice "Mouse1" "CorePointer"
    InputDevice "Keyboard1" "CoreKeyboard"

EndSection

# Section "DRI"
#    Mode 0666
# EndSection
Активен

spawnman

  • Напреднали
  • *****
  • Публикации: 455
    • Профил
Scrol na mishkata & Slackware 10.1
« Отговор #8 -: Mar 19, 2005, 09:33 »
Цитат
Option "Emulate3Buttons"

Коментирай този ред и пробвай пак!
Активен

Mandriva Cooker
BlackBox

FV80503200 SL27J, 82437FX TSC, 128 (4x32) MB 72pin EDO, AHA-2940UW, ST34572W, M2513A, CDU521, CTL0024, 3C509b-TPC, 215R3PUA22, FP767-12

Подобни теми
Заглавие Започната от Отговора Прегледи Последна публикация
mishkata mi ne bachka
Настройка на хардуер
iasen 2 2103 Последна публикация Aug 27, 2002, 02:13
от pirx
Problem s mishkata.
Настройка на хардуер
tomby 2 1892 Последна публикация Jun 06, 2003, 21:00
от BasiDi
scrol na mi6ka
Настройка на хардуер
PAIN1 3 1584 Последна публикация Nov 24, 2003, 08:22
от PAIN1
kak da si pusna mishkata pod bsd
Настройка на хардуер
babok 1 1478 Последна публикация Dec 16, 2003, 16:59
от
mishkata i klawiaturata ne bachkat!
Настройка на хардуер
Andronoff 0 1043 Последна публикация Nov 28, 2004, 18:32
от Andronoff