acpi=off   - параметър към ядрото при първоначално зареждане.

[Цитат]

Цитат

forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60. ACPI: PCI Interrupt Link [APCH] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 21 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:0a.0 to 64 forcedeth: using HIGHDMA 0000:00:0a.0: Invalid Mac address detected: 71:5a:e6:7d:1d:00 Please complain to your hardware vendor. Switching to a random MAC. eth0: forcedeth.c: subsystem: 01458:e000 bound to 0000:00:0a.0

Заради това ги върти, флашни си биоса ... и на предната тема ти казах.
След това от биоса си оправи прекъсванията ...гледай да не би лан и звук да са на едно и също.

Ако питаш с цел да разбереш дали Слака е виновен - не е той. '>

According to Documentation/kernel-parameters.txt, acpi=off should still work ( предполагам че това ще замаже нещата )

Флашни си БИОС-а на дъното.

[Цитат]

Цитат

0000:00:0a.0: Invalid Mac address detected: 71:5a:e6:7d:1d:00 Please complain to your hardware vendor. Switching to a random MAC.

Защо е това съобщение ?

Това дали ще ти помогне ?
http://bhavesh.freeshell.org/cloninghd.html

...а попаднах и на това :
http://lrs.linbox.org/wiki/WikiStartEn

[Цитат]

Цитат

п.с. Ако всеки препращаше към гоогъл, по форумите нямаше да има какво да се прочете.

Ха ха ха ха, прав си ..но ако обърнеш внимание, пращането за търсене в гугъл е индиректен начин да напомниш на някой че е редно да се потруди поне малко. (абе имам и друго обяснение но спазвам добрият тон '> )
Та ...има доста неща написани на български ... (а как ще настройваш апач и уебмин ...вероятно ще срещнем в друг твой въпрос '> '> )

[Цитат]

Цитат

За да ми върши истинска работа

Какво толкова искаш да работиш с това ?
Сигурно вече си преровил форума http://forums.hamachi.cc/viewforum.php?f=15
а и това което видях във " Linux Howto "  има не само как се инсталира '> . А за още по яко ти препоръчвам да търсиш в Гугъл - Хамачи ( на български ) - пълно е с информация.

да бе оставил и контакт за обратна връзка, би било още по-добре.

http://www.youtube.com/watch?v=eCbQqsRm41s&NR=1

Поредният глупак който незнае какво иска.

[Цитат]

Цитат

Първата е прекалено садистична...

Дрън дрън ... то тогава тази изобщо не я гледай '>
тази

UMBRO
 '>

BMW M5
'>

[Цитат]

vikktor прочети внимателно това :

Цитат

The Image Files     IDE bootdisks (.i suffix) bare.i This is the disk to use for installation on most IDE based PCs, with support for nearly all IDE controllers and support for IDE/ATAPI CD-ROM/DVD drives. Most CD-ROM drives made today fall into this category.   bareacpi.i This is similar to the bare.i bootdisk, but the kernel also contains support for ACPI (Advanced Configuration and Power Interface). If you aren't using a laptop, then you probably will not need ACPI (or APM) support.   ataraid.i This is a bootdisk with support for IDE RAID controllers. The install disks now have preliminary support for these controllers as well. The drivers included are: 3ware Hardware ATA-RAID controllers. Promise Fasttrak™ IDE RAID. Highpoint 370 software RAID. Many of these controllers will require some degree of do-it-yourself setup before and/or after installation.   lowmem.i This is a really stripped-down Linux kernel which might be useful for installing on IDE systems with a low amount of RAM (less than 8MB). It's also the only Slackware kernel that supports old 386 machines. If bare.i runs into problems, you might try this. NOTE: On systems with extremely low memory (4MB), ZipSlack plus the fourmeg.zip add-on (found in the zipslack directory) may boot and run even in cases where lowmem.i doesn't. If you have to use lowmem.i to install, you'll then probably have to compile a custom kernel with the minimal additional features that your machine requires.   old_cd.i This is a version of bare.i with additional support for old CD-ROM drives on non-standard proprietary interfaces. The CD-ROM drives supported by this bootdisk are: Aztech CDA268-01A, Orchid CD-3110, Okano/Wearnes CDD110, Conrad TXC, CyCDROM CR520, CR540. Sony CDU31/33a CD-ROM. Sony CDU531/535 CD-ROM. Philips/LMS cm206 CD-ROM with cm260 adapter card. Goldstar R420 CD-ROM (sometimes sold in a 'Reveal Multimedia Kit''>. ISP16/MAD16/Mozart CD-ROM drives. NON-IDE Mitsumi CD-ROM support. Optics Storage 8000 AT CD-ROM (the 'DOLPHIN' drive). Sanyo CDR-H94A CD-ROM support. Matsushita, Kotobuki, Panasonic, CreativeLabs (Sound Blaster), Longshine and Teac NON-IDE CD-ROM support.   pportide.i This is an extended version of bare.i with support for a wide variety of parallel-port IDE devices. Supports parallel-port products from MicroSolutions, Hewlett-Packard, SyQuest, Imation, Avatar, and other manufacturers.   sata.i This is a version of bare.i with support for SATA controllers made by Promise, Silicon Image, SiS, ServerWorks / Apple K2, VIA, and Vitesse.       SCSI bootdisks (.s suffix) adaptec.s This bootdisk supports most Adaptec SCSI controllers, including these models: AHA-1510, AHA-1520, AHA-1522, AHA-1522, AHA-1740, and AHA-2825. The AIC7xxx models, which include the 274x EISA cards; 284x VLB cards; 2902, 2910, 293x, 294x, 394x, 3985 and several other PCI and motherboard based SCSI controllers from Adaptec. Adaptec's I2O based RAID controllers (including OEM Adaptec RAID controllers used by HP and Dell, Adaptec branded AAC964/5400 RAID controllers, and DPT SmartRaid V cards)   ibmmca.s This is a bootdisk based on a development kernel which supports MicroChannel Architecture, found in some IBM PS/2 machines and laptops. It is a bus system similar to PCI or ISA. Support for most MCA SCSI, Ethernet, and Token Ring adapters is included.   jfs.s A version of bare.i with support for IBM's Journaled Filesystem as well as Adaptec AIC7xxx SCSI support.   raid.s This is a bootdisk with support for some hardware SCSI and ATA RAID controllers. The install disks now have preliminary support for these controllers as well. The drivers included are: AMI MegaRAID 418, 428, 438, 466, 762, 490 and 467 SCSI host adapters, Compaq Smart, Compaq Smart Array 5xxx, IBM ServeRAID hardware RAID, LSI Logic Fusion™ MPT devices (not really RAID, but added since there was room for this driver here), Mylex DAC960, AcceleRAID, and eXtremeRAID controllers. Many of these controllers will require some degree of do-it-yourself setup before and/or after installation.   scsi.s This is a SCSI bootdisk with support for various controllers. Note that this disk does not include Adaptec support any longer -- you must use the adaptec.s bootdisk for that. This disk supports these SCSI controllers: AM53/79C974 PCI SCSI, BusLogic SCSI, EATA ISA/EISA/PCI (DPT and generic EATA/DMA-compliant boards), Initio 91XXU(W) and Initio 91XXU(W), SYM53C8XX Version 2, Qlogic ISP SCSI, Qlogic QLA 1280 SCSI.   scsi2.s This is a SCSI bootdisk with support for various controllers. This disk supports these SCSI controllers: AdvanSys SCSI (supports all AdvanSys SCSI controllers, including some SCSI cards included with HP CD-R/RW drives, the Iomega Jaz Jet SCSI controller, and the SCSI controller on the Iomega Buz multimedia adapter), ACARD 870U/W SCSI host adapter, Compaq Fibre Channel 64-bit/66Mhz HBA, Domex DMX3191D SCSI Host Adapters, DTC 3180/3280 SCSI Host Adapters, Future Domain 16xx SCSI/AHA-2920A, NCR53c7, 8xx, NCR53C8XX   scsi3.s This is a SCSI bootdisk with support for various controllers. This disk supports these SCSI controllers: Western Digital 7000FASST SCSI support, Always IN2000, Intel/ICP (former GDT SCSI Disk Array) RAID Controller, PCI2000I, PCI2220i, PSI240i EIDE interface card, Qlogic FAS SCSI, QLogic ISP FC (ISP2100 SCSI-FCP), Seagate ST01/ST02, Future Domain TMC-885/950 SCSI, SYM53c416 SCSI host adapter, UltraStor 14F, 24F and 34F SCSI-2 host adapters, Workbit NinjaSCSI-32Bi/UDE   speakup.s This is like the bare.i (standard IDE) disk, but has support for Speakup (and since there was space, support for Adaptec's AIC7xxx SCSI controllers is also included) Speakup provides access to Linux for the visually impaired community. It does this by sending console output to a number of different hardware speech synthesizers. It provides access to Linux by making screen review functions available. For more information about speakup and its drivers check out: http://www.linux-speakup.org. To use this, you'll need to specify one of the supported synthesizers on the bootdisk's boot prompt: ramdisk speakup_synth=synth where 'synth' is one of the supported speech synthesizers: acntpc, acntsa, apolo, audptr, bns, decext, dectlk, dtlk, ltlk, spkout, txprt   xfs.s This is an extended version of bare.i with support for SGI's XFS filesystem. Support for Adaptec's AIC7xxx SCSI controllers is also included.

както и FAQ-овете... и по-точно

Цитат

Q: I can't get the kernel to see a CDROM connected to a Soundblaster 16 IDE!

[Цитат]

Дебитните карти са бял кахър ... давайте за лихвени проценти при кредити .... ипотечни. Това е доста по-сериозно от това какви са картите - с чип или не.
На мен ми е интересно например защо повечето си траят за едностранната промяна на договорените вече проценти (познайте от коя страна) и защо при вече сключен договор за кредит ти пращат уведомително писмо как ...видиш ли били размислили относно лихвеният процент и как ... ти променят вноската по погасяване на кредита ...

Цитат

//off евала, divak  за пореден път, влезе изненадващо на ринга "сипа" по малко на всеки и излезе А, какво става, къде съм ?!?

'> хахаха, gotha що зорлем акаш срещу вентилатора ? Седи мирен ...чувала със зобта още ми е отворен ... '>

[Цитат]

bulg само това ли са ти критериите за банка ?
Само от нездраво любопитство - кой е правил превода към грешната (откраднатата) карта ?
И ... ти какво искаш да правиш ? Кредит ли ще теглиш, дебитна карта ли ще си вадиш, кредитна ... ипотечен заем ... кредит по бизнес план, или може би ги сравняваш по лихвен процент за влогове и различните видове кредити ? Ако си избираш банка по условията които си посочил ... по-добре карай на кеш и ще си спестиш ядовете '> . Определения за банка от този вид -"съвестно си гледат работата " ...заради една дебитна карта ... е доста весело.

HeavenWarrior не мислиш ли че коректноста би трябвало да е взаимна ? Те ти превеждат грешно пари - а ти си строши краката от бързане да ги уведомиш за грешката и да ги върнеш ? '>

Цитат

групировката ТИМ

- това предполагам е някаква нова организация ... със нестопанска цел . '>

[Цитат]

vikktor прочети внимателно това :

Цитат

The Image Files     IDE bootdisks (.i suffix) bare.i This is the disk to use for installation on most IDE based PCs, with support for nearly all IDE controllers and support for IDE/ATAPI CD-ROM/DVD drives. Most CD-ROM drives made today fall into this category.   bareacpi.i This is similar to the bare.i bootdisk, but the kernel also contains support for ACPI (Advanced Configuration and Power Interface). If you aren't using a laptop, then you probably will not need ACPI (or APM) support.   ataraid.i This is a bootdisk with support for IDE RAID controllers. The install disks now have preliminary support for these controllers as well. The drivers included are: 3ware Hardware ATA-RAID controllers. Promise Fasttrak™ IDE RAID. Highpoint 370 software RAID. Many of these controllers will require some degree of do-it-yourself setup before and/or after installation.   lowmem.i This is a really stripped-down Linux kernel which might be useful for installing on IDE systems with a low amount of RAM (less than 8MB). It's also the only Slackware kernel that supports old 386 machines. If bare.i runs into problems, you might try this. NOTE: On systems with extremely low memory (4MB), ZipSlack plus the fourmeg.zip add-on (found in the zipslack directory) may boot and run even in cases where lowmem.i doesn't. If you have to use lowmem.i to install, you'll then probably have to compile a custom kernel with the minimal additional features that your machine requires.   old_cd.i This is a version of bare.i with additional support for old CD-ROM drives on non-standard proprietary interfaces. The CD-ROM drives supported by this bootdisk are: Aztech CDA268-01A, Orchid CD-3110, Okano/Wearnes CDD110, Conrad TXC, CyCDROM CR520, CR540. Sony CDU31/33a CD-ROM. Sony CDU531/535 CD-ROM. Philips/LMS cm206 CD-ROM with cm260 adapter card. Goldstar R420 CD-ROM (sometimes sold in a 'Reveal Multimedia Kit''>. ISP16/MAD16/Mozart CD-ROM drives. NON-IDE Mitsumi CD-ROM support. Optics Storage 8000 AT CD-ROM (the 'DOLPHIN' drive). Sanyo CDR-H94A CD-ROM support. Matsushita, Kotobuki, Panasonic, CreativeLabs (Sound Blaster), Longshine and Teac NON-IDE CD-ROM support.   pportide.i This is an extended version of bare.i with support for a wide variety of parallel-port IDE devices. Supports parallel-port products from MicroSolutions, Hewlett-Packard, SyQuest, Imation, Avatar, and other manufacturers.   sata.i This is a version of bare.i with support for SATA controllers made by Promise, Silicon Image, SiS, ServerWorks / Apple K2, VIA, and Vitesse.       SCSI bootdisks (.s suffix) adaptec.s This bootdisk supports most Adaptec SCSI controllers, including these models: AHA-1510, AHA-1520, AHA-1522, AHA-1522, AHA-1740, and AHA-2825. The AIC7xxx models, which include the 274x EISA cards; 284x VLB cards; 2902, 2910, 293x, 294x, 394x, 3985 and several other PCI and motherboard based SCSI controllers from Adaptec. Adaptec's I2O based RAID controllers (including OEM Adaptec RAID controllers used by HP and Dell, Adaptec branded AAC964/5400 RAID controllers, and DPT SmartRaid V cards)   ibmmca.s This is a bootdisk based on a development kernel which supports MicroChannel Architecture, found in some IBM PS/2 machines and laptops. It is a bus system similar to PCI or ISA. Support for most MCA SCSI, Ethernet, and Token Ring adapters is included.   jfs.s A version of bare.i with support for IBM's Journaled Filesystem as well as Adaptec AIC7xxx SCSI support.   raid.s This is a bootdisk with support for some hardware SCSI and ATA RAID controllers. The install disks now have preliminary support for these controllers as well. The drivers included are: AMI MegaRAID 418, 428, 438, 466, 762, 490 and 467 SCSI host adapters, Compaq Smart, Compaq Smart Array 5xxx, IBM ServeRAID hardware RAID, LSI Logic Fusion™ MPT devices (not really RAID, but added since there was room for this driver here), Mylex DAC960, AcceleRAID, and eXtremeRAID controllers. Many of these controllers will require some degree of do-it-yourself setup before and/or after installation.   scsi.s This is a SCSI bootdisk with support for various controllers. Note that this disk does not include Adaptec support any longer -- you must use the adaptec.s bootdisk for that. This disk supports these SCSI controllers: AM53/79C974 PCI SCSI, BusLogic SCSI, EATA ISA/EISA/PCI (DPT and generic EATA/DMA-compliant boards), Initio 91XXU(W) and Initio 91XXU(W), SYM53C8XX Version 2, Qlogic ISP SCSI, Qlogic QLA 1280 SCSI.   scsi2.s This is a SCSI bootdisk with support for various controllers. This disk supports these SCSI controllers: AdvanSys SCSI (supports all AdvanSys SCSI controllers, including some SCSI cards included with HP CD-R/RW drives, the Iomega Jaz Jet SCSI controller, and the SCSI controller on the Iomega Buz multimedia adapter), ACARD 870U/W SCSI host adapter, Compaq Fibre Channel 64-bit/66Mhz HBA, Domex DMX3191D SCSI Host Adapters, DTC 3180/3280 SCSI Host Adapters, Future Domain 16xx SCSI/AHA-2920A, NCR53c7, 8xx, NCR53C8XX   scsi3.s This is a SCSI bootdisk with support for various controllers. This disk supports these SCSI controllers: Western Digital 7000FASST SCSI support, Always IN2000, Intel/ICP (former GDT SCSI Disk Array) RAID Controller, PCI2000I, PCI2220i, PSI240i EIDE interface card, Qlogic FAS SCSI, QLogic ISP FC (ISP2100 SCSI-FCP), Seagate ST01/ST02, Future Domain TMC-885/950 SCSI, SYM53c416 SCSI host adapter, UltraStor 14F, 24F and 34F SCSI-2 host adapters, Workbit NinjaSCSI-32Bi/UDE   speakup.s This is like the bare.i (standard IDE) disk, but has support for Speakup (and since there was space, support for Adaptec's AIC7xxx SCSI controllers is also included) Speakup provides access to Linux for the visually impaired community. It does this by sending console output to a number of different hardware speech synthesizers. It provides access to Linux by making screen review functions available. For more information about speakup and its drivers check out: http://www.linux-speakup.org. To use this, you'll need to specify one of the supported synthesizers on the bootdisk's boot prompt: ramdisk speakup_synth=synth where 'synth' is one of the supported speech synthesizers: acntpc, acntsa, apolo, audptr, bns, decext, dectlk, dtlk, ltlk, spkout, txprt   xfs.s This is an extended version of bare.i with support for SGI's XFS filesystem. Support for Adaptec's AIC7xxx SCSI controllers is also included.

както и FAQ-овете... и по-точно

Цитат

Q: I can't get the kernel to see a CDROM connected to a Soundblaster 16 IDE!