Титла: Mint Debian неочакван проблем с звука Публикувано от: NikolaiTalev в Jun 05, 2011, 10:41 Здравейте до снощи звука на PC-то ми беше страхотен (комшиите могат да потвардят ;D) ,но след като натиснах бутона на клавиатурата mute след това повече не тръгна много странно ???
Картата ми е Creative Sound Blaster SB0570. Преинсталирах Pulseaudio и пак нищо (никакъв звук) Махнах креатива и пробвах с вградената и пак няма звук Какъв може да е проблема? Титла: Re: Mint Debian неочакван проблем с звука Публикувано от: cybercop в Jun 05, 2011, 11:02 Махни pulseaudio, инсталирай gnome-alsamixer, рестартирай, отвори миксера и провери контролерите за звука. може някой да е на намален. Ако звукът тръгне отново можеш да си инсталираш pulseaudio. Системата си работи добре и без него, само при стартиране на vlc излиза едно досадно съобщение.
Титла: Re: Mint Debian неочакван проблем с звука Публикувано от: NikolaiTalev в Jun 05, 2011, 11:46 Махни pulseaudio, инсталирай gnome-alsamixer, рестартирай, отвори миксера и провери контролерите за звука. може някой да е на намален. Ако звукът тръгне отново можеш да си инсталираш pulseaudio. Системата си работи добре и без него, само при стартиране на vlc излиза едно досадно съобщение. Пробвах но пак нищо и реших да пробвам дали хардуера е здрав и бутнах едно livecd и се оказа че работи .............. Мистерията е пълна П.П Нищо не ми идва на акъла пробвах всичко което се сетих и пак без резултат а не искам да преинсталирам системата върви чудесно с изключение на издънката с звука Титла: Re: Mint Debian неочакван проблем с звука Публикувано от: radoshow в Jun 05, 2011, 12:52 А dmesg нищо ли не казва?
Титла: Re: Mint Debian неочакван проблем с звука Публикувано от: NikolaiTalev в Jun 05, 2011, 12:54 А dmesg нищо ли не казва?[ 0.108342] pci 0000:01:00.0: supports D1 D2 [ 0.108366] pci 0000:01:00.1: [1002:5d44] type 0 class 0x000380 [ 0.108384] pci 0000:01:00.1: reg 10: [mem 0xd8000000-0xdfffffff pref] [ 0.108396] pci 0000:01:00.1: reg 14: [mem 0xb0110000-0xb011ffff] [ 0.108452] pci 0000:01:00.1: supports D1 D2 [ 0.108503] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 0.108510] pci 0000:00:01.0: bridge window [io 0x2000-0x2fff] [ 0.108516] pci 0000:00:01.0: bridge window [mem 0xb0100000-0xb01fffff] [ 0.108523] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff pref] [ 0.108568] pci 0000:02:08.0: [8086:1039] type 0 class 0x000200 [ 0.108590] pci 0000:02:08.0: reg 10: [mem 0xb0200000-0xb0200fff] [ 0.108603] pci 0000:02:08.0: reg 14: [io 0x3000-0x303f] [ 0.108668] pci 0000:02:08.0: supports D1 D2 [ 0.108672] pci 0000:02:08.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.108679] pci 0000:02:08.0: PME# disabled [ 0.108705] pci 0000:02:09.0: [14f1:8800] type 0 class 0x000400 [ 0.108728] pci 0000:02:09.0: reg 10: [mem 0xb1000000-0xb1ffffff] [ 0.108831] pci 0000:02:09.1: [14f1:8801] type 0 class 0x000480 [ 0.108852] pci 0000:02:09.1: reg 10: [mem 0xb2000000-0xb2ffffff] [ 0.108957] pci 0000:02:0c.0: [1102:0007] type 0 class 0x000401 [ 0.108979] pci 0000:02:0c.0: reg 10: [io 0x3040-0x305f] [ 0.109054] pci 0000:02:0c.0: supports D1 D2 [ 0.109093] pci 0000:00:1e.0: PCI bridge to [bus 02-02] (subtractive decode) [ 0.109100] pci 0000:00:1e.0: bridge window [io 0x3000-0x3fff] [ 0.109107] pci 0000:00:1e.0: bridge window [mem 0xb0200000-0xb2ffffff] [ 0.109115] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 0.109120] pci 0000:00:1e.0: bridge window [io 0x0000-0xffff] (subtractive decode) [ 0.109125] pci 0000:00:1e.0: bridge window [mem 0x00000000-0xffffffff] (subtractive decode) [ 0.109143] pci_bus 0000:00: on NUMA node 0 [ 0.109150] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.109320] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SLOT._PRT] [ 0.109561] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] [ 0.166095] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12 14 15), disabled. [ 0.166197] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *9 10 11 12 14 15), disabled. [ 0.166296] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 9 10 11 12 14 15), disabled. [ 0.166394] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 *10 11 12 14 15), disabled. [ 0.166497] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 *11 12 14 15), disabled. [ 0.166601] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 *9 10 11 12 14 15), disabled. [ 0.166704] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. [ 0.166808] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 *9 10 11 12 14 15), disabled. [ 0.166975] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none [ 0.166983] vgaarb: loaded [ 0.167052] PCI: Using ACPI for IRQ routing [ 0.167058] PCI: pci_cache_line_size set to 64 bytes [ 0.167139] reserve RAM buffer: 000000000009f800 - 000000000009ffff [ 0.167144] reserve RAM buffer: 000000007fef0000 - 000000007fffffff [ 0.167149] reserve RAM buffer: 000000007ff80000 - 000000007fffffff [ 0.169562] pnp: PnP ACPI init [ 0.169604] ACPI: bus type pnp registered [ 0.170648] pnp 00:00: [bus 00-ff] [ 0.170653] pnp 00:00: [io 0x0000-0x0cf7 window] [ 0.170658] pnp 00:00: [io 0x0cf8-0x0cff] [ 0.170662] pnp 00:00: [io 0x0d00-0xffff window] [ 0.170666] pnp 00:00: [mem 0x000a0000-0x000bffff window] [ 0.170671] pnp 00:00: [mem 0x000c0000-0x000c3fff window] [ 0.170675] pnp 00:00: [mem 0x000c4000-0x000c7fff window] [ 0.170679] pnp 00:00: [mem 0x000c8000-0x000cbfff window] [ 0.170683] pnp 00:00: [mem 0x000cc000-0x000cffff window] [ 0.170687] pnp 00:00: [mem 0x000d0000-0x000d3fff window] [ 0.170692] pnp 00:00: [mem 0x000d4000-0x000d7fff window] [ 0.170696] pnp 00:00: [mem 0x000d8000-0x000dbfff window] [ 0.170700] pnp 00:00: [mem 0x000dc000-0x000dffff window] [ 0.170704] pnp 00:00: [mem 0x000e0000-0x000e3fff window] [ 0.170708] pnp 00:00: [mem 0x000e4000-0x000e7fff window] [ 0.170712] pnp 00:00: [mem 0x000e8000-0x000ebfff window] [ 0.170717] pnp 00:00: [mem 0x000ec000-0x000effff window] [ 0.170721] pnp 00:00: [mem 0x80000000-0xfebfffff window] [ 0.170811] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active) [ 0.170954] pnp 00:01: [io 0x0010-0x001f] [ 0.170959] pnp 00:01: [io 0x0024-0x0025] [ 0.170963] pnp 00:01: [io 0x0028-0x0029] [ 0.170967] pnp 00:01: [io 0x002c-0x002d] [ 0.170970] pnp 00:01: [io 0x002e-0x002f] [ 0.170974] pnp 00:01: [io 0x0030-0x0031] [ 0.170978] pnp 00:01: [io 0x0034-0x0035] [ 0.170981] pnp 00:01: [io 0x0038-0x0039] [ 0.170985] pnp 00:01: [io 0x003c-0x003d] [ 0.170989] pnp 00:01: [io 0x004e-0x004f] [ 0.170992] pnp 00:01: [io 0x0050-0x0053] [ 0.170996] pnp 00:01: [io 0x0072-0x0077] [ 0.170999] pnp 00:01: [io 0x0080] [ 0.171003] pnp 00:01: [io 0x0090-0x009f] [ 0.171007] pnp 00:01: [io 0x00a4-0x00a5] [ 0.171010] pnp 00:01: [io 0x00a8-0x00a9] [ 0.171019] pnp 00:01: [io 0x00ac-0x00ad] [ 0.171023] pnp 00:01: [io 0x00b0-0x00b5] [ 0.171027] pnp 00:01: [io 0x00b8-0x00b9] [ 0.171031] pnp 00:01: [io 0x00bc-0x00bd] [ 0.171035] pnp 00:01: [io 0x04d0-0x04d1] [ 0.171038] pnp 00:01: [io 0xfe00] [ 0.171042] pnp 00:01: [io 0x0800-0x087f] [ 0.171046] pnp 00:01: [io 0x1000-0x107f] [ 0.171050] pnp 00:01: [io 0x1100-0x111f] [ 0.171054] pnp 00:01: [io 0x1180-0x11bf] [ 0.171058] pnp 00:01: [mem 0xeffffc00] [ 0.171199] system 00:01: [io 0x04d0-0x04d1] has been reserved [ 0.171205] system 00:01: [io 0xfe00] has been reserved [ 0.171210] system 00:01: [io 0x0800-0x087f] has been reserved [ 0.171215] system 00:01: [io 0x1000-0x107f] has been reserved [ 0.171220] system 00:01: [io 0x1100-0x111f] has been reserved [ 0.171225] system 00:01: [io 0x1180-0x11bf] has been reserved [ 0.171231] system 00:01: [mem 0xeffffc00] has been reserved [ 0.171237] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.171257] pnp 00:02: [io 0x0000-0x000f] [ 0.171261] pnp 00:02: [io 0x0081-0x008f] [ 0.171265] pnp 00:02: [io 0x00c0-0x00df] [ 0.171269] pnp 00:02: [dma 4] [ 0.171319] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active) [ 0.171338] pnp 00:03: [io 0x00f0-0x00fe] [ 0.171357] pnp 00:03: [irq 13] [ 0.171408] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.171430] pnp 00:04: [io 0x0070-0x0071] [ 0.171438] pnp 00:04: [irq 8] [ 0.171489] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.171507] pnp 00:05: [io 0x0061] [ 0.171563] pnp 00:05: Plug and Play ACPI device, IDs PNP0800 (active) [ 0.171826] pnp 00:06: [mem 0xff800000-0xffffffff] [ 0.171883] pnp 00:06: Plug and Play ACPI device, IDs INT0800 (active) [ 0.171961] pnp 00:07: [io 0x0060] [ 0.171965] pnp 00:07: [io 0x0064] [ 0.171973] pnp 00:07: [irq 1] [ 0.172058] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active) [ 0.172183] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.172273] pnp 00:09: [irq 12] [ 0.172347] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.177748] pnp 00:0a: [io 0x03f0-0x03f5] [ 0.177753] pnp 00:0a: [io 0x03f7] [ 0.177762] pnp 00:0a: [irq 6] [ 0.177766] pnp 00:0a: [dma 2] [ 0.179563] pnp 00:0a: Plug and Play ACPI device, IDs PNP0700 (active) [ 0.184091] pnp 00:0b: [io 0x03f8-0x03ff] [ 0.184101] pnp 00:0b: [irq 4] [ 0.185952] pnp 00:0b: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.194219] pnp 00:0c: [io 0x02f8-0x02ff] [ 0.194229] pnp 00:0c: [irq 3] [ 0.196168] pnp 00:0c: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.204093] pnp 00:0d: [io 0x0378-0x037f] [ 0.204098] pnp 00:0d: [io 0x0778-0x077f] [ 0.204107] pnp 00:0d: [irq 7] [ 0.204111] pnp 00:0d: [dma 3] [ 0.206505] pnp 00:0d: Plug and Play ACPI device, IDs PNP0401 (active) [ 0.209419] pnp: PnP ACPI: found 14 devices [ 0.209423] ACPI: ACPI bus type pnp unregistered [ 0.209429] PnPBIOS: Disabled by ACPI PNP [ 0.248905] Switching to clocksource acpi_pm [ 0.248977] pci 0000:01:00.0: BAR 6: assigned [mem 0xb0120000-0xb013ffff pref] [ 0.248983] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 0.248989] pci 0000:00:01.0: bridge window [io 0x2000-0x2fff] [ 0.248998] pci 0000:00:01.0: bridge window [mem 0xb0100000-0xb01fffff] [ 0.249005] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff pref] [ 0.249015] pci 0000:00:1e.0: PCI bridge to [bus 02-02] [ 0.249020] pci 0000:00:1e.0: bridge window [io 0x3000-0x3fff] [ 0.249028] pci 0000:00:1e.0: bridge window [mem 0xb0200000-0xb2ffffff] [ 0.249035] pci 0000:00:1e.0: bridge window [mem pref disabled] [ 0.249062] pci 0000:00:1e.0: setting latency timer to 64 [ 0.249070] pci_bus 0000:00: resource 0 [io 0x0000-0xffff] [ 0.249074] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff] [ 0.249079] pci_bus 0000:01: resource 0 [io 0x2000-0x2fff] [ 0.249083] pci_bus 0000:01: resource 1 [mem 0xb0100000-0xb01fffff] [ 0.249088] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff pref] [ 0.249092] pci_bus 0000:02: resource 0 [io 0x3000-0x3fff] [ 0.249096] pci_bus 0000:02: resource 1 [mem 0xb0200000-0xb2ffffff] [ 0.249100] pci_bus 0000:02: resource 4 [io 0x0000-0xffff] [ 0.249104] pci_bus 0000:02: resource 5 [mem 0x00000000-0xffffffff] [ 0.249194] NET: Registered protocol family 2 [ 0.249333] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.249881] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.251185] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.251185] Switched to NOHz mode on CPU #0 [ 0.251209] TCP: Hash tables configured (established 131072 bind 65536) [ 0.251214] TCP reno registered [ 0.251230] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.251263] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.251608] NET: Registered protocol family 1 [ 0.251750] pci 0000:01:00.0: Boot video device [ 0.251784] PCI: CLS 32 bytes, default 64 [ 0.251890] Unpacking initramfs... [ 3.341689] Freeing initrd memory: 6860k freed [ 3.353902] Simple Boot Flag at 0x6c set to 0x1 [ 3.354475] audit: initializing netlink socket (disabled) [ 3.354501] type=2000 audit(1307267438.351:1): initialized [ 3.367198] highmem bounce pool size: 64 pages [ 3.367208] HugeTLB registered 4 MB page size, pre-allocated 0 pages [ 3.370722] VFS: Disk quotas dquot_6.5.2 [ 3.370907] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 3.371124] msgmni has been set to 1731 [ 3.371487] alg: No test for stdrng (krng) [ 3.371594] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 3.371601] io scheduler noop registered [ 3.371604] io scheduler deadline registered [ 3.371627] io scheduler cfq registered (default) [ 3.371988] ERST: Table is not found! [ 3.372060] isapnp: Scanning for PnP cards... [ 3.726155] isapnp: No Plug & Play device found [ 3.726295] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 3.746697] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 3.767122] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 3.787920] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 3.808422] 00:0c: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 3.808687] Linux agpgart interface v0.103 [ 3.808877] agpgart-intel 0000:00:00.0: Intel 845G Chipset [ 3.816464] agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xc0000000 [ 3.816705] i8042: PNP: PS/2 Controller [PNP0303:KBC] at 0x60,0x64 irq 1 [ 3.816710] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp [ 3.817195] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 3.817392] mousedev: PS/2 mouse device common for all mice [ 3.817462] rtc_cmos 00:04: RTC can wake from S4 [ 3.817549] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0 [ 3.817577] rtc0: alarms up to one month, y3k, 114 bytes nvram [ 3.817597] cpuidle: using governor ladder [ 3.817601] cpuidle: using governor menu [ 3.818038] TCP cubic registered [ 3.818298] NET: Registered protocol family 10 [ 3.819340] Mobile IPv6 [ 3.819345] NET: Registered protocol family 17 [ 3.819352] Registering the dns_resolver key type [ 3.819388] Using IPI No-Shortcut mode [ 3.819577] PM: Hibernation image not present or could not be loaded. [ 3.819603] registered taskstats version 1 [ 3.820090] rtc_cmos 00:04: setting system clock to 2011-06-05 09:50:39 UTC (1307267439) [ 3.820156] Initalizing network drop monitor service [ 3.820266] Freeing unused kernel memory: 392k freed [ 3.820861] Write protecting the kernel text: 2648k [ 3.820884] Write protecting the kernel read-only data: 1000k [ 3.835681] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 [ 3.860228] <30>udev[45]: starting version 167 [ 4.207521] thermal LNXTHERM:00: registered as thermal_zone0 [ 4.207527] ACPI: Thermal Zone [THM0] (53 C) [ 4.208330] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI [ 4.208335] e100: Copyright(c) 1999-2006 Intel Corporation [ 4.208416] e100 0000:02:08.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 4.236541] FDC 0 is a post-1991 82077 [ 4.332151] e100 0000:02:08.0: PME# disabled [ 4.333345] e100 0000:02:08.0: eth0: addr 0xb0200000, irq 20, MAC addr 00:09:6b:11:d3:43 [ 4.348971] usbcore: registered new interface driver usbfs [ 4.349294] usbcore: registered new interface driver hub [ 4.349379] usbcore: registered new device driver usb [ 4.358659] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.358726] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23 [ 4.358760] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 4.358767] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 4.358840] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 [ 4.362779] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported [ 4.362808] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xb0000000 [ 4.366689] Refined TSC clocksource calibration: 1993.531 MHz. [ 4.366695] Switching to clocksource tsc [ 4.369255] SCSI subsystem initialized [ 4.382446] uhci_hcd: USB Universal Host Controller Interface driver [ 4.415794] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 4.415870] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.415876] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.415880] usb usb1: Product: EHCI Host Controller [ 4.415884] usb usb1: Manufacturer: Linux 2.6.38-2-686 ehci_hcd [ 4.415887] usb usb1: SerialNumber: 0000:00:1d.7 [ 4.417712] libata version 3.00 loaded. [ 4.424622] hub 1-0:1.0: USB hub found [ 4.424634] hub 1-0:1.0: 6 ports detected [ 4.424800] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4.424816] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 4.424822] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 4.424837] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 4.424886] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00001800 [ 4.424944] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 4.424950] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.424954] usb usb2: Product: UHCI Host Controller [ 4.424958] usb usb2: Manufacturer: Linux 2.6.38-2-686 uhci_hcd [ 4.424961] usb usb2: SerialNumber: 0000:00:1d.0 [ 4.425176] hub 2-0:1.0: USB hub found [ 4.425184] hub 2-0:1.0: 2 ports detected [ 4.425315] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 4.425326] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 4.425331] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 4.425344] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 [ 4.425390] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001820 [ 4.425446] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 4.425451] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.425455] usb usb3: Product: UHCI Host Controller [ 4.425459] usb usb3: Manufacturer: Linux 2.6.38-2-686 uhci_hcd [ 4.425462] usb usb3: SerialNumber: 0000:00:1d.1 [ 4.425638] hub 3-0:1.0: USB hub found [ 4.425648] hub 3-0:1.0: 2 ports detected [ 4.425767] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 4.425777] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 4.425782] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 4.425796] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 [ 4.425836] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001840 [ 4.425891] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 4.425896] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.425900] usb usb4: Product: UHCI Host Controller [ 4.425903] usb usb4: Manufacturer: Linux 2.6.38-2-686 uhci_hcd [ 4.425907] usb usb4: SerialNumber: 0000:00:1d.2 [ 4.426084] hub 4-0:1.0: USB hub found [ 4.426092] hub 4-0:1.0: 2 ports detected [ 4.426846] ata_piix 0000:00:1f.1: version 2.13 [ 4.426870] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 4.426943] ata_piix 0000:00:1f.1: setting latency timer to 64 [ 4.430236] scsi0 : ata_piix [ 4.434480] scsi1 : ata_piix [ 4.435793] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1860 irq 14 [ 4.435798] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1868 irq 15 [ 4.601308] ata1.00: ATA-8: WDC WD3200AAJB-00J3A0, 01.03E01, max UDMA/133 [ 4.601315] ata1.00: 625142448 sectors, multi 16: LBA48 [ 4.608374] ata2.00: ATAPI: HL-DT-STDVD-RAM GSA-H55N, 1.02, max UDMA/66 [ 4.617343] ata1.00: configured for UDMA/100 [ 4.617531] scsi 0:0:0:0: Direct-Access ATA WDC WD3200AAJB-0 01.0 PQ: 0 ANSI: 5 [ 4.624311] ata2.00: configured for UDMA/66 [ 4.626833] scsi 1:0:0:0: CD-ROM HL-DT-ST DVD-RAM GSA-H55N 1.02 PQ: 0 ANSI: 5 [ 4.662780] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB) [ 4.662880] sd 0:0:0:0: [sda] Write Protect is off [ 4.662886] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.662929] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.666771] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray [ 4.666778] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 4.667481] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 4.680981] sda: sda1 sda2 sda3 [ 4.681716] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.712121] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 4.713054] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 4.920030] usb 3-1: new low speed USB device using uhci_hcd and address 2 [ 5.095353] usb 3-1: New USB device found, idVendor=046d, idProduct=c016 [ 5.095361] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 5.095366] usb 3-1: Product: Optical USB Mouse [ 5.095369] usb 3-1: Manufacturer: Logitech [ 5.155924] input: Logitech Optical USB Mouse as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input1 [ 5.156250] generic-usb 0003:046D:C016.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.1-1/input0 [ 5.156609] usbcore: registered new interface driver usbhid [ 5.156616] usbhid: USB HID core driver [ 5.160326] Btrfs loaded [ 5.619684] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 7.530571] <30>udev[277]: starting version 167 [ 8.053082] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 8.083422] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 8.223508] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0A03:00/PNP0C0C:00/input/input2 [ 8.223520] ACPI: Power Button [PWRB] [ 8.223636] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 [ 8.223643] ACPI: Power Button [PWRF] [ 8.229198] intel_rng: Firmware space is locked read-only. If you can't or [ 8.229202] intel_rng: don't want to disable this in firmware setup, and if [ 8.229204] intel_rng: you are certain that your system has a functional [ 8.229206] intel_rng: RNG, try using the 'no_fwh_detect' option. [ 8.247188] ACPI: acpi_idle registered with cpuidle [ 8.250465] <30>udev[291]: renamed network interface eth0 to eth1 [ 8.724412] parport_pc 00:0d: reported by Plug and Play ACPI [ 8.724478] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE] [ 8.881370] Linux video capture interface: v2.00 [ 8.972977] [drm] Initialized drm 1.1.0 20060810 [ 9.060651] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 9.060662] ACPI: resource 0000:00:1f.3 [io 0x1880-0x189f] conflicts with ACPI region SMBR [io 0x1880-0x1887] [ 9.060666] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 9.584930] IR NEC protocol handler initialized [ 9.598385] cx88/0: cx2388x v4l2 driver version 0.0.8 loaded [ 9.598452] cx8800 0000:02:09.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 9.603411] cx88[0]: subsystem: 1554:4935, board: PixelView PlayTV Ultra Pro (Stereo) [card=27,insmod option], frontend(s): 0 [ 9.603416] cx88[0]: TV tuner type 38, Radio tuner type 1 [ 9.620216] IR RC5(x) protocol handler initialized [ 9.682031] [drm] radeon kernel modesetting enabled. [ 9.682122] radeon 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9.692462] [drm] initializing kernel modesetting (RV280 0x1002:0x5964). [ 9.692528] [drm] register mmio base: 0xB0100000 [ 9.692531] [drm] register mmio size: 65536 [ 9.697196] agpgart-intel 0000:00:00.0: AGP 2.0 bridge [ 9.700674] agpgart-intel 0000:00:00.0: putting AGP V2 device into 4x mode [ 9.700711] radeon 0000:01:00.0: putting AGP V2 device into 4x mode [ 9.700751] radeon 0000:01:00.0: GTT: 128M 0xC0000000 - 0xC7FFFFFF [ 9.700758] [drm] Generation 2 PCI interface, using max accessible memory [ 9.700766] radeon 0000:01:00.0: VRAM: 128M 0x00000000D0000000 - 0x00000000D7FFFFFF (128M used) [ 9.700791] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 9.700795] [drm] Driver supports precise vblank timestamp query. [ 9.700816] [drm] radeon: irq initialized. [ 9.700825] [drm] Detected VRAM RAM=128M, BAR=128M [ 9.700829] [drm] RAM width 64bits DDR [ 9.700899] [TTM] Zone kernel: Available graphics memory: 443474 kiB. [ 9.700903] [TTM] Zone highmem: Available graphics memory: 1037110 kiB. [ 9.700907] [TTM] Initializing pool allocator. [ 9.700940] [drm] radeon: 128M of VRAM memory ready [ 9.700944] [drm] radeon: 128M of GTT memory ready. [ 9.702456] radeon 0000:01:00.0: WB disabled [ 9.703348] [drm] Loading R200 Microcode [ 9.772791] IR RC6 protocol handler initialized [ 9.793342] i2c-core: driver [tuner] using legacy suspend method [ 9.793348] i2c-core: driver [tuner] using legacy resume method [ 9.810419] IR JVC protocol handler initialized [ 9.822820] tuner 0-0061: chip found @ 0xc2 (cx88[0]) [ 9.895708] cx2388x alsa driver version 0.0.8 loaded [ 10.025853] IR Sony protocol handler initialized [ 10.058387] lirc_dev: IR Remote Control driver registered, major 251 [ 10.065943] tuner-simple 0-0061: creating new instance [ 10.065950] tuner-simple 0-0061: type set to 1 (Philips PAL_I (FI1246 and compatibles)) [ 10.071932] IR LIRC bridge handler initialized [ 10.161178] [drm] radeon: ring at 0x00000000C0001000 [ 10.161202] [drm] ring test succeeded in 1 usecs [ 10.161716] [drm] radeon: ib pool ready. [ 10.161826] [drm] ib test succeeded in 0 usecs [ 10.162305] [drm] Radeon Display Connectors [ 10.162309] [drm] Connector 0: [ 10.162311] [drm] VGA [ 10.162316] [drm] DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60 [ 10.162319] [drm] Encoders: [ 10.162321] [drm] CRT1: INTERNAL_DAC1 [ 10.162325] [drm] Connector 1: [ 10.162327] [drm] DVI-I [ 10.162329] [drm] HPD1 [ 10.162334] [drm] DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64 [ 10.162336] [drm] Encoders: [ 10.162339] [drm] CRT2: INTERNAL_DAC2 [ 10.162342] [drm] DFP1: INTERNAL_TMDS1 [ 10.162345] [drm] Connector 2: [ 10.162347] [drm] S-video [ 10.162349] [drm] Encoders: [ 10.162352] [drm] TV1: INTERNAL_DAC2 [ 10.168136] Registered IR keymap rc-pixelview-mk12 [ 10.168340] input: cx88 IR (PixelView PlayTV Ultra as /devices/pci0000:00/0000:00:1e.0/0000:02:09.0/rc/rc0/input4 [ 10.168452] rc0: cx88 IR (PixelView PlayTV Ultra as /devices/pci0000:00/0000:00:1e.0/0000:02:09.0/rc/rc0 [ 10.168465] cx88[0]/0: found at 0000:02:09.0, rev: 5, irq: 21, latency: 165, mmio: 0xb1000000 [ 10.286871] cx88[0]/0: registered device video0 [v4l2] [ 10.287011] cx88[0]/0: registered device vbi0 [ 10.287130] cx88[0]/0: registered device radio0 [ 10.292127] cx88_audio 0000:02:09.1: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 10.292172] cx88[0]/1: CX88x/0: ALSA support for cx2388x boards [ 10.293580] CA0106 0000:02:0c.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 10.293635] snd-ca0106: Model 100a Rev 00000000 Serial 100a1102 [ 10.561258] [drm] fb mappable at 0xD0040000 [ 10.561264] [drm] vram apper at 0xD0000000 [ 10.561267] [drm] size 7057408 [ 10.561270] [drm] fb depth is 24 [ 10.561273] [drm] pitch is 6720 [ 10.561541] fbcon: radeondrmfb (fb0) is primary device [ 10.647973] Console: switching to colour frame buffer device 210x65 [ 10.680463] fb0: radeondrmfb frame buffer device [ 10.680467] drm: registered panic notifier [ 10.681065] [drm] Initialized radeon 2.8.0 20080528 for 0000:01:00.0 on minor 0 [ 11.797428] EXT4-fs (sda2): re-mounted. Opts: (null) [ 12.038241] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ 12.167427] loop: module loaded [ 12.430673] Adding 524284k swap on /root/swap.img. Priority:-1 extents:6 across:647164k [ 12.773905] EXT4-fs (sda3): warning: maximal mount count reached, running e2fsck is recommended [ 12.781246] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null) [ 13.839015] fuse init (API version 7.16) [ 17.381165] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 17.384174] e100 0000:02:08.0: eth1: NIC Link is Up 100 Mbps Full Duplex [ 17.384554] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 18.934977] Bluetooth: Core ver 2.15 [ 18.935024] NET: Registered protocol family 31 [ 18.935028] Bluetooth: HCI device and connection manager initialized [ 18.935034] Bluetooth: HCI socket layer initialized [ 19.025247] Bluetooth: L2CAP ver 2.15 [ 19.025252] Bluetooth: L2CAP socket layer initialized [ 19.141595] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 19.141602] Bluetooth: BNEP filters: protocol multicast [ 19.388390] Bluetooth: SCO (Voice Link) ver 0.6 [ 19.388396] Bluetooth: SCO socket layer initialized [ 20.221674] lp0: using parport0 (interrupt-driven). [ 20.360453] ppdev: user-space parallel port driver [ 28.088015] eth1: no IPv6 routers present [ 32.035077] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro,commit=0 [ 32.113709] EXT4-fs (sda3): re-mounted. Opts: commit=0 [ 210.775276] exe (2004): /proc/2004/oom_adj is deprecated, please use /proc/2004/oom_score_adj instead. Титла: Re: Mint Debian неочакван проблем с звука Публикувано от: AMD в Jun 05, 2011, 13:15 Аз бих казал "lsmod"
"lspci" И дай изходите тук Титла: Re: Mint Debian неочакван проблем с звука Публикувано от: AMD в Jun 05, 2011, 13:15 Махни pulseaudio, инсталирай gnome-alsamixer, рестартирай, отвори миксера и провери контролерите за звука. може някой да е на намален. Ако звукът тръгне отново можеш да си инсталираш pulseaudio. Системата си работи добре и без него, само при стартиране на vlc излиза едно досадно съобщение. Проблема не е в Pulseaudio! Титла: Re: Mint Debian неочакван проблем с звука Публикувано от: radoshow в Jun 05, 2011, 13:16 Щом казваш,че си инсталирал alsa пробвай тези две команди да видиш дали ще се появи звука
Код
Титла: Re: Mint Debian неочакван проблем с звука Публикувано от: NikolaiTalev в Jun 05, 2011, 13:30 Щом казваш,че си инсталирал alsa пробвай тези две команди да видиш дали ще се появи звука Пак не става Module Size Used by mperf 12387 0 speedstep_lib 12463 0 cpufreq_userspace 12520 0 cpufreq_powersave 12422 0 cpufreq_conservative 13598 0 cpufreq_stats 12670 0 ppdev 12621 0 lp 12858 0 sco 13219 2 rfcomm 31960 0 bnep 17147 2 l2cap 35435 4 bnep,rfcomm bluetooth 50119 6 sco,bnep,rfcomm,l2cap rfkill 18510 2 bluetooth binfmt_misc 12778 1 fuse 55640 1 loop 17805 0 snd_ca0106 32954 1 snd_ac97_codec 83645 1 snd_ca0106 ac97_bus 12462 1 snd_ac97_codec tvaudio 26237 0 snd_seq_midi 12744 0 rc_pixelview_mk12 12374 0 ir_lirc_codec 12651 0 tuner_simple 16926 1 lirc_dev 12797 1 ir_lirc_codec tuner_types 12305 1 tuner_simple snd_rawmidi 22407 2 snd_ca0106,snd_seq_midi ir_sony_decoder 12403 0 cx88_alsa 12979 1 ir_jvc_decoder 12401 0 snd_pcm_oss 35864 0 tuner 21352 1 ir_rc6_decoder 12401 0 snd_seq_midi_event 13124 1 snd_seq_midi radeon 641550 3 snd_seq 39172 2 snd_seq_midi,snd_seq_midi_event snd_mixer_oss 17649 1 snd_pcm_oss ttm 46672 1 radeon cx8800 26721 0 snd_pcm 52774 4 snd_ca0106,snd_ac97_codec,cx88_alsa,snd_pcm_oss ir_rc5_decoder 12401 0 snd_seq_device 12995 3 snd_seq_midi,snd_rawmidi,snd_seq ir_nec_decoder 12401 0 snd_timer 22171 2 snd_seq,snd_pcm cx88xx 67340 2 cx88_alsa,cx8800 drm_kms_helper 26501 1 radeon rc_core 17813 9 rc_pixelview_mk12,ir_lirc_codec,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,ir_nec_decoder,cx88xx drm 128416 5 radeon,ttm,drm_kms_helper tveeprom 16473 1 cx88xx v4l2_common 13215 4 tvaudio,tuner,cx8800,cx88xx snd 38153 14 snd_ca0106,snd_ac97_codec,snd_rawmidi,cx88_alsa,snd_pcm_oss,snd_seq,snd_mixer_oss,snd_pcm,snd_seq_device,snd_timer videodev 48418 5 tvaudio,tuner,cx8800,cx88xx,v4l2_common soundcore 12878 1 snd parport_pc 21895 1 snd_page_alloc 12841 2 snd_ca0106,snd_pcm i2c_algo_bit 12706 2 radeon,cx88xx power_supply 13283 1 radeon i2c_i801 12670 0 parport 27018 3 ppdev,lp,parport_pc videobuf_dma_sg 12992 3 cx88_alsa,cx8800,cx88xx i2c_core 18989 13 tvaudio,tuner_simple,tuner,radeon,cx8800,cx88xx,drm_kms_helper,tveeprom,drm,v4l2_common,videodev,i2c_algo_bit,i2c_i801 videobuf_core 17540 3 cx8800,cx88xx,videobuf_dma_sg btcx_risc 12499 3 cx88_alsa,cx8800,cx88xx rng_core 12550 0 shpchp 26653 0 tpm_tis 12949 0 pci_hotplug 26303 1 shpchp tpm 17476 1 tpm_tis evdev 13084 9 processor 26983 0 button 12866 0 tpm_bios 12799 1 tpm container 12525 0 ext4 251726 2 mbcache 12810 1 ext4 jbd2 55701 1 ext4 crc16 12327 2 l2cap,ext4 btrfs 419292 0 zlib_deflate 21186 1 btrfs crc32c 12576 1 libcrc32c 12394 1 btrfs usbhid 35168 0 hid 59736 1 usbhid sg 21385 0 sr_mod 17418 0 sd_mod 34941 3 crc_t10dif 12332 1 sd_mod cdrom 34631 1 sr_mod ata_generic 12439 0 ata_piix 21079 2 libata 131904 2 ata_generic,ata_piix uhci_hcd 21850 0 ehci_hcd 34889 0 scsi_mod 134369 4 sg,sr_mod,sd_mod,libata usbcore 99058 4 usbhid,uhci_hcd,ehci_hcd thermal 13058 0 e100 31317 0 floppy 47893 0 thermal_sys 17667 2 processor,thermal mii 12562 1 e100 nls_base 12649 1 usbcore lspci 00:00.0 Host bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host-Hub Interface (rev 01) 00:01.0 PCI bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE Host-to-AGP Bridge (rev 01) 00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01) 00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 81) 00:1f.0 ISA bridge: Intel Corporation 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge (rev 01) 00:1f.1 IDE interface: Intel Corporation 82801DB (ICH4) IDE Controller (rev 01) 00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 01) 01:00.0 VGA compatible controller: ATI Technologies Inc RV280 [Radeon 9200 SE] (rev 01) 01:00.1 Display controller: ATI Technologies Inc RV280 [Radeon 9200 SE] (Secondary) (rev 01) 02:08.0 Ethernet controller: Intel Corporation 82801DB PRO/100 VE (LOM) Ethernet Controller (rev 81) 02:09.0 Multimedia video controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder (rev 05) 02:09.1 Multimedia controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port] (rev 05) 02:0c.0 Multimedia audio controller: Creative Labs CA0106 Soundblaster ето и локализиран изход от lspci lspci | grep Audio 02:09.0 Multimedia video controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder (rev 05) 02:09.1 Multimedia controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port] (rev 05) Титла: Re: Mint Debian неочакван проблем с звука Публикувано от: AMD в Jun 05, 2011, 16:01 А защо едновременно две звукови карти работят ?!
Титла: Re: Mint Debian неочакван проблем с звука Публикувано от: ЗибелтБг в Jun 05, 2011, 22:22 в конзолата:
alsamixer и виж какво не си вдигнал. И защо никой не каза да инсталира PulseAudio Volume Control!!!!!!!!И не махай PulseAudio!!! Титла: Re: Mint Debian неочакван проблем с звука Публикувано от: NikolaiTalev в Jun 05, 2011, 23:38 в конзолата: PulseAudio Volume Control си го имам от alsamixer-а всичко е вдигнато все пак звука изчезна при работеща система всичко си го имам то това е най-загадъчното и това ме мъчи най-много ??? Всичко стана бях си пуснал филм и телефона ми звънна и натиснах mute-то от клавиатурата говорих какво говорих вечерях и след около час, като цъкнах на muteto-то отново звукът не тръгна и от тук почнаха мъките рестартове ...... и какво ли не ...... Когато причината е във мен и аз счупя нещо не ме е яд, но тук работата е много тънка, защото за мен дистрибуцията е, като "жената" до сега не се бе дънила нито веднъж нито ми е забивал просто "вярна " но ето че снощи ми "изневери" За това за мен е по-важно причината, а не толкова решението защото винаги мога да преинсталирам (колкото и да не ми се иска) Базиках се тия дни с хранилищата във форума попаднах на едни от @AMD и бях с тях и не знам от тези врътки да не се омаза звука ??? П.П Най-ме е яд че тъкмо си направих много кустом иконки на програми като ми харесват на GIMP-a и сега звука............ Титла: Re: Mint Debian неочакван проблем с звука Публикувано от: antivirys в Jun 05, 2011, 23:40 На дебиан имах такъв проблем , графичната среда ми беше КДЕ и след ъпграде ми сложи пулсеаудио , реших да го премахна като го истрия, след рестарта звука работеше използвам алса иначе :) [_]3 [_]3
Титла: Re: Mint Debian неочакван проблем с звука Публикувано от: NikolaiTalev в Jun 05, 2011, 23:44 На дебиан имах такъв проблем , графичната среда ми беше КДЕ и след ъпграде ми сложи пулсеаудио , реших да го премахна като го истрия, след рестарта звука работеше използвам алса иначе :) [_]3 [_]3 Най-интересното е че puseaudio го трих и инсталирах 4 пъти без резултат махнах cretive и пробвах и на вграденото аудио пак без резултат пробвах и alsa и пак бе успешно просо звук няма никакъв Титла: Re: Mint Debian неочакван проблем с звука Публикувано от: kalinik в Jun 06, 2011, 01:09 Дай да почнем отначало - явно си леко нервен и е възможно да пропускаш нещо (съдя по себе си ).
Предлагам следния вариант: -забраняваш вграденото аудио от BIOS-а -пускаш OS-a и нагласяш от звуковия аплет DEFAULT да ти е Creative. (Добра идея е да го пуснеш в режим STEREO) -проверяваш: cat /proc/asound/card - картата с индекс 0 (НУЛА) е default. +aко НЕ Е dafault - знам един много груб начин :D Проверяваш cat /proc/asound/modules какви са звуковите драйвъри и си ги записваш, БЕЗ този на Creative . После ги слагаш в черния списък : etc/modprobe.d/blacklist.conf > описваш ги вътре blacklist нежелания-драйвър -отваряш инструмента за настройка на потребителите и се добавяш към групата AUDIO (и/или ALSA) -рестартираш и повтаряш горните стъпки докато Creative стане default устройство -пускаш да свири нещо, като ЗАДЪЛЖИТЕЛНО го настройваш за изход ALSA !!! -пускаш alsamixer и с F6 избираш картата ти -вдигаш всичко над половината -откриваш настройката "Analog/Digital Output Jack" и натискаш 'm' - би трябвало да ти показва '00' и да чуваш звукЪт ! Ако все още не се чува - последното, което се сещам, е да смениш правата на звуковите устройства: # chmod o=+rw /dev/mixer* # chmod o=+rw /dev/dsp* Защото и на мен ми се е случвало след инсталиране на някакво pulseaudio-dev и разни други щуротии - да се прецака звука. 99% съм сигурен, че прецакването се дължи на някой пакет, който не е трябвало да се инсталира. Стискам палци Титла: Re: Mint Debian неочакван проблем с звука Публикувано от: Arvigeus в Jun 06, 2011, 09:34 Глупав въпрос (защото при мен се е случвало нещо подобно)
Я си виж Sound Applet-а от Notification Area. При мен има bug понякога при mute да се mute-ва и после да не приема ябсолютно никакви специални клавиши за unmute-ване или за промяна на звука, въпреки, че ги отчита натиснати. Просто цъкни върху аплета и виж случайно слайдера да не ти е в най-долно (заглушено) състояние. Ако да - просто го плъзни нагоре Титла: Re: Mint Debian неочакван проблем с звука Публикувано от: ЗибелтБг в Jun 08, 2011, 19:53 Абе човече-не се прави на знаещ-инсталирай от синаптика PulseAudio Volume Control!!!!!! и се оправяй-ей-не го научихте това Пулс Аудио!!!!
|