Изпечатай

[LinuxuserX]

Здравейте,
на лаптопа ми от доста време като го стартирам трябва да въвеждам llformat за да ме пусне напред.

Ето информация от програмата :

Код:

ATA device, with non-removable media
Model Number:       WDC WD3200BPVT-80JJ5T0                 
Serial Number:      WD-WX81E71XUZ42
Firmware Revision:  01.01A01
Transport:          Serial, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6
Standards:
Supported: 8 7 6 5
Likely used: 8
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors:   16514064
LBA    user addressable sectors:  268435455
LBA48  user addressable sectors:  625142448
Logical  Sector size:                   512 bytes
Physical Sector size:                  4096 bytes
Logical Sector-0 offset:                  0 bytes
device size with M = 1024*1024:      305245 MBytes
device size with M = 1000*1000:      320072 MBytes (320 GB)
cache/buffer size  = 8192 KBytes
Nominal Media Rotation Rate: 5400
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
     Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
     Cycle time: no flow control=120ns  IORDY flow control=120ns
Commands/features:
Enabled Supported:
   * SMART feature set
   * Security Mode feature set
   * Power Management feature set
   * Write cache
   * Look-ahead
   * Host Protected Area feature set
   * WRITE_BUFFER command
   * READ_BUFFER command
   * NOP cmd
   * DOWNLOAD_MICROCODE
   * Advanced Power Management feature set
    SET_MAX security extension
   * 48-bit Address feature set
   * Device Configuration Overlay feature set
   * Mandatory FLUSH_CACHE
   * FLUSH_CACHE_EXT
   * SMART error logging
   * SMART self-test
   * General Purpose Logging feature set
   * 64-bit World wide name
   * IDLE_IMMEDIATE with UNLOAD
   * {READ,WRITE}_DMA_EXT_GPL commands
   * Segmented DOWNLOAD_MICROCODE
   * Gen1 signaling speed (1.5Gb/s)
   * Gen2 signaling speed (3.0Gb/s)
   * Native Command Queueing (NCQ)
   * Host-initiated interface power management
   * Phy event counters
   * Idle-Unload when NCQ is active
   * NCQ priority information
   * DMA Setup Auto-Activate optimization
    Device-initiated interface power management
   * Software settings preservation
   * SMART Command Transport (SCT) feature set
   * SCT Write Same (AC2)
   * SCT Features Control (AC4)
   * SCT Data Tables (AC5)
    unknown 206[12] (vendor specific)
    unknown 206[13] (vendor specific)
    unknown 206[14] (vendor specific)
Security:
Master password revision code = 1
supported
enabled
not locked
frozen
not expired: security count
supported: enhanced erase
Security level high
70min for SECURITY ERASE UNIT. 70min for ENHANCED SECURITY ERASE UNIT.
Logical Unit WWN Device Identifier: 50014ee601f1a7f7
NAA : 5
IEEE OUI : 0014ee
Unique ID : 601f1a7f7
Checksum: correct

Предполагам първо ми трябва Suspend. После с коя команда да я премахна ?

Linux Mint 18

Мерси!

[10101]

root@thinkpad:~# hdparm --Istdout /dev/sdb > sdb.ata_identify
root@thinkpad:~# P="$(ruby pw.rb sdb.ata_identify)"
Enter password: <<interactively asks for password>>
root@thinkpad:~# hdparm --security-disable $P /dev/sdb
security_password="GARBAGE"

/dev/sdb:
Issuing SECURITY_DISABLE command, password="GARBAGE", user=user


Now, hdparm -I gives me the following:

Code:
Security:
   Master password revision code = 16385
      supported
   not   enabled
   not   locked
   not   frozen
   not   expired: security count
      supported: enhanced erase
   94min for SECURITY ERASE UNIT. 94min for ENHANCED SECURITY ERASE UNIT.


https://forum.hddguru.com/viewtopic.php?f=1&t=32046

[LinuxuserX]

Здравейте,
при мен дискът е монтиран на /dev/sda1

Да заменя ли dev/sdb с dev/sda1 ?

Това просто ще махне паролата без да трие данни или ?

[LinuxuserX]

UP ?