Титла: Лило , как да добавя още едно ядро ? Публикувано от: Pavlik в Apr 27, 2010, 19:43 Лило , как да добавя още едно ядро ? е вие сте :)
Титла: Re: Лило , как да добавя още едно ядро ? Публикувано от: ROKO__ в Apr 27, 2010, 19:46 Много лесно.
Само кажи имената на ядрата или по точно замествай по примера ====== boot=/dev/sda lba32 title Laino GNU delay 1200 # opredelya sled kolko sekundi da se bootne sistemata image = /boot/laino ro vga=795 initrd = /boot/laino.img # ako ima initrd Титла: Re: Лило , как да добавя още едно ядро ? Публикувано от: Pavlik в Apr 27, 2010, 20:29 Ето какво пише в него :) Ядрото е версия => 2.6.33.1
# LILO configuration file # generated by 'liloconfig' # # Start LILO global section # Append any additional kernel parameters: append=" vt.default_utf8=0" boot = /dev/sda # Boot BMP Image. # Bitmap in BMP format: 640x480x8 bitmap = /boot/slack.bmp # Menu colors (foreground, background, shadow, highlighted # foreground, highlighted background, highlighted shadow): bmp-colors = 255,0,255,0,255,0 # Location of the option table: location x, location y, number of # columns, lines per column (max 15), "spill" (this is how many # entries must be in the first column before the next begins to # be used. We don't specify it here, as there's just one column. bmp-table = 60,6,1,16 # Timer location x, timer location y, foreground color, # background color, shadow color. bmp-timer = 65,27,0,255 # Standard menu. # Or, you can comment out the bitmap menu above and # use a boot message with the standard menu: #message = /boot/boot_message.txt # Wait until the timeout to boot (if commented out, boot the # first entry immediately): prompt # Timeout before the first entry boots. # This is given in tenths of a second, so 600 for every minute: timeout = 1200 # Override dangerous defaults that rewrite the partition table: change-rules reset # VESA framebuffer console @ 1024x768x256 vga = 773 # Normal VGA console # vga = normal # VESA framebuffer console @ 1024x768x64k # vga=791 # VESA framebuffer console @ 1024x768x32k # vga=790 # VESA framebuffer console @ 1024x768x256 # vga=773 # VESA framebuffer console @ 800x600x64k # vga=788 # VESA framebuffer console @ 800x600x32k # vga=787 # VESA framebuffer console @ 800x600x256 # vga=771 # VESA framebuffer console @ 640x480x64k # vga=785 # VESA framebuffer console @ 640x480x32k # vga=784 # VESA framebuffer console @ 640x480x256 # vga=769 # End LILO global section # Linux bootable partition config begins image = /boot/vmlinuz root = /dev/sda1 label = Linux read-only # Linux bootable partition config ends Титла: Re: Лило , как да добавя още едно ядро ? Публикувано от: ROKO__ в Apr 27, 2010, 20:59 Ето какво пише в него :) Ядрото е версия => 2.6.33.1 Ползваш тези редове image = /boot/vmlinuz root = /dev/sda1 label = Linux read-only Като на мястото на vmlinuz слагаш новото ядро (името му) na root слагаш дяля на който е новото ядро ако е на същия дял остава sda1 после запазваш файла и изпълняваш "lilo" след това рестартираш (ако лило не ти даде грешка де) |