Титла: Slakware 12.1 - няма звук Публикувано от: viv1111 в Nov 29, 2008, 14:36 Отворих тази тема, но моля да не обръщаме моя въпрос в спам-бълвакане. Не ме препращайте към: - Прочети това, прочети онова. Защото много четох, но не намерих отговор на първия въпрос. Просто помогнете, ако знаете как.
1. Когато влеза като обикновен потребител нямам звук. Съобщението още в началото е: “Грешка в инициализирането на sound driver: device /dev/dsp can`t be opened (Permission denied) The sound server will continueq using the null autput.” Мъчих се по какъв ли не начин, но /dev/dsp винаги си остава собственост на root и достъпа до него от users е невъзможен. Няма меню от което да променя настройките в sound server-а. Отговора при: “man -k saund” е “saund: nothing appropriate” 2. След инсталирането на ATI двайвера за видеокартата, който ползвам, видеоплеъра gxine – Video Player не работи нормално. Картината е на малки, цветни, хоризонтални черти. С Kaffeine и VLC няма проблеми. Не мога да остана на началните настройки на видеокартата, защото ми е необходимо 3D, за да ползвам Googleearth. 3. Така и не можах да подкарам смяната на BDS и US от клавиатурата. Имах предложения от членове на форума, как да направя това, но не се получава. Ами, това е за сега. Дай Боже да нямам други проблеми със Слакуера. Титла: Re: Slakware 12.1 - няма звук Публикувано от: nedpetko в Nov 29, 2008, 14:50 Добре няма да те пращаме никъде, надявам се!
1. Добави ли си потребителя в групата audio? Пише се: sound 2. Нямам Ati видеокарти, т.е. нямам опит с тях. edit: Излъгах, имам такива чудеса на техниката ама не им се втелясвам и не ползвам 3D в/у тях. 3. Това кото ти писах в другата тема направи ли го? За да работи коректно е необходимо да спреш напълно -> disable <- на вградената в KDE опция "Locale" Титла: Re: Slakware 12.1 - няма звук Публикувано от: viv1111 в Nov 29, 2008, 15:39 Nedpetko, направих каквото ми препоръча. Промених xorg.conf, но нищо не се получава. Но, проблема със звука е вече сериозен проблем. Сбъркал съм с изписването. Случва се.
Титла: Re: Slakware 12.1 - няма звук Публикувано от: sonyj7 в Nov 29, 2008, 18:12 Като добавиш user към audio групата трябва да направиш log out и после login. Според мен най-добре е да направиш рестарт. Аз добавям групи към user чрез старт меню/system и после Kuser. Аз лично за кирилица използвам bglinux под слака и нямам проблеми. Успех.
Титла: Re: Slakware 12.1 - няма звук Публикувано от: nedpetko в Nov 29, 2008, 18:39 За промяната на xorg.conf не се съмнявам, но по важно е да се спре KDE locale - онова със знаменцето долу вдясно.
Просто когато искаш да използваш клавишите за смяна на локализацията, КДЕ локейл прави проблем. И то така го прави че да ти иде да го напсуваш. Я вземи си прикачи или откопирай тука xorg.conf. Титла: Re: Slakware 12.1 - няма звук Публикувано от: viv1111 в Nov 29, 2008, 22:24 Nedpetko, правя това, което ме посъветва още първия път и сега. Спирам, разбира се KDE locale. Понеже се наложи да преинсталирам Слакуер-а изпращам съществуващият след преинсталазията xorg.conf. Единствената промяна, която съм правил в него се отнася до мишката. Понеже Слакуер не инсталира мишка с три бутона и трябва допълнително да се пипне xorg.conf.
# File generated by xf86config. # # Copyright (c) 1999 by The XFree86 Project, Inc. # # Permission is hereby granted, free of charge, to any person obtaining a # copy of this software and associated documentation files (the "Software"), # to deal in the Software without restriction, including without limitation # the rights to use, copy, modify, merge, publish, distribute, sublicense, # and/or sell copies of the Software, and to permit persons to whom the # Software is furnished to do so, subject to the following conditions: # # The above copyright notice and this permission notice shall be included in # all copies or substantial portions of the Software. # # THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR # IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, # FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL # THE XFREE86 PROJECT BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, # WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF # OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE # SOFTWARE. # # Except as contained in this notice, the name of the XFree86 Project shall # not be used in advertising or otherwise to promote the sale, use or other # dealings in this Software without prior written authorization from the # XFree86 Project. # # ********************************************************************** # Refer to the XF86Config(4/5) man page for details about the format of # this file. # ********************************************************************** # NOTE: This is a NEW IMPROVED version of XF86Config-fbdev that uses the vesa # driver instead of the fbdev driver. Thanks to Kenneth Fanyo who pointed # this out to me. :) # This XF86Config file is designed for use with the VESA framebuffer. # This generic interface should work with nearly all video cards # (although not every card will support every resolution). # With the new driver, it should no longer be required to have frame buffer # support in the kernel, or to run it on the console. # # Enjoy! :) # -- volkerdi@slackware.com # # ********************************************************************** # Module section -- this section is used to specify # which dynamically loadable modules to load. # ********************************************************************** # # ********************************************************************** # Files section. This allows default font and rgb paths to be set # ********************************************************************** # ********************************************************************** # Server flags section. # ********************************************************************** # ********************************************************************** # Input devices # ********************************************************************** # ********************************************************************** # Core keyboard's InputDevice section # ********************************************************************** # ********************************************************************** # Core Pointer's InputDevice section # ********************************************************************** # Some examples of extended input devices # Section "InputDevice" # Identifier "spaceball" # Driver "magellan" # Option "Device" "/dev/cua0" # EndSection # # Section "InputDevice" # Identifier "spaceball2" # Driver "spaceorb" # Option "Device" "/dev/cua0" # EndSection # # Section "InputDevice" # Identifier "touchscreen0" # Driver "microtouch" # Option "Device" "/dev/ttyS0" # Option "MinX" "1412" # Option "MaxX" "15184" # Option "MinY" "15372" # Option "MaxY" "1230" # Option "ScreenNumber" "0" # Option "ReportingMode" "Scaled" # Option "ButtonNumber" "1" # Option "SendCoreEvents" # EndSection # # Section "InputDevice" # Identifier "touchscreen1" # Driver "elo2300" # Option "Device" "/dev/ttyS0" # Option "MinX" "231" # Option "MaxX" "3868" # Option "MinY" "3858" # Option "MaxY" "272" # Option "ScreenNumber" "0" # Option "ReportingMode" "Scaled" # Option "ButtonThreshold" "17" # Option "ButtonNumber" "1" # Option "SendCoreEvents" # EndSection # ********************************************************************** # Monitor section # ********************************************************************** # Any number of monitor sections may be present # ********************************************************************** # Graphics device section # ********************************************************************** # Any number of graphics device sections may be present # ********************************************************************** # Screen sections # ********************************************************************** # Any number of screen sections may be present. Each describes # the configuration of a single screen. A single specific screen section # may be specified from the X server command line with the "-screen" # option. # ********************************************************************** # ServerLayout sections. # ********************************************************************** # Any number of ServerLayout sections may be present. Each describes # the way multiple screens are organised. A specific ServerLayout # section may be specified from the X server command line with the # "-layout" option. In the absence of this, the first section is used. # When now ServerLayout section is present, the first Screen section # is used alone. Section "ServerLayout" # The Identifier line must be present # Each Screen line specifies a Screen section name, and optionally # the relative position of other screens. The four names after # primary screen name are the screens to the top, bottom, left and right # of the primary screen. In this example, screen 2 is located to the # right of screen 1. # Each InputDevice line specifies an InputDevice section name and # optionally some options to specify the way the device is to be # used. Those options include "CorePointer", "CoreKeyboard" and # "SendCoreEvents". Identifier "Simple Layout" Screen 0 "aticonfig-Screen[0]-0" 0 0 InputDevice "Mouse1" "CorePointer" InputDevice "Keyboard1" "CoreKeyboard" EndSection Section "Files" # The location of the RGB database. Note, this is the name of the # file minus the extension (like ".txt" or ".db"). There is normally # no need to change the default. # Multiple FontPath entries are allowed (which are concatenated together), # as well as specifying multiple comma-separated entries in one FontPath # command (or a combination of both methods) # # If you don't have a floating point coprocessor and emacs, Mosaic or other # programs take long to start up, try moving the Type1 and Speedo directory # to the end of this list (or comment them out). # # ModulePath can be used to set a search path for the X server modules. # The default path is shown here. # ModulePath "/usr/lib/xorg/modules" RgbPath "/usr/share/X11/rgb" FontPath "/usr/share/fonts/local/" FontPath "/usr/share/fonts/misc/" FontPath "/usr/share/fonts/OTF/" FontPath "/usr/share/fonts/TTF/" FontPath "/usr/share/fonts/Type1/" FontPath "/usr/share/fonts/CID/" FontPath "/usr/share/fonts/Speedo/" FontPath "/usr/share/fonts/75dpi/:unscaled" FontPath "/usr/share/fonts/100dpi/:unscaled" FontPath "/usr/share/fonts/75dpi/" FontPath "/usr/share/fonts/100dpi/" FontPath "/usr/share/fonts/cyrillic/" EndSection Section "Module" # This loads the DBE extension module. # This loads the miscellaneous extensions module, and disables # initialisation of the XFree86-DGA extension within that module. # This loads the font modules # This loads the GLX module Load "dbe" # Double buffer extension SubSection "extmod" Option "omit xfree86-dga" # don't initialise the DGA extension EndSubSection Load "type1" Load "freetype" #Load "speedo" Load "glx" EndSection Section "InputDevice" # For most OSs the protocol can be omitted (it defaults to "Standard"). # When using XQUEUE (only for SVR3 and SVR4, but not Solaris), # uncomment the following line. # Option "Protocol" "Xqueue" # Set the keyboard auto repeat parameters. Not all platforms implement # this. # Option "AutoRepeat" "500 5" # Specifiy which keyboard LEDs can be user-controlled (eg, with xset(1)). # Option "Xleds" "1 2 3" # To disable the XKEYBOARD extension, uncomment XkbDisable. # Option "XkbDisable" # To customise the XKB settings to suit your keyboard, modify the # lines below (which are the defaults). For example, for a European # keyboard, you will probably want to use one of: # # Option "XkbModel" "pc102" # Option "XkbModel" "pc105" # # If you have a Microsoft Natural keyboard, you can use: # # Option "XkbModel" "microsoft" # # If you have a US "windows" keyboard you will want: # # Option "XkbModel" "pc104" # # Then to change the language, change the Layout setting. # For example, a german layout can be obtained with: # # Option "XkbLayout" "de" # # or: # # Option "XkbLayout" "de" # Option "XkbVariant" "nodeadkeys" # # If you'd like to switch the positions of your capslock and # control keys, use: # # Option "XkbOptions" "ctrl:swapcaps" # These are the default XKB settings for X.Org # # Option "XkbRules" "xorg" # Option "XkbModel" "pc105" # Option "XkbLayout" "us" # Option "XkbVariant" "" # Option "XkbOptions" "" Identifier "Keyboard1" Driver "kbd" EndSection Section "InputDevice" # Identifier and driver # On platforms where PnP mouse detection is supported the following # protocol setting can be used when using a newer PnP mouse: # Option "Protocol" "Auto" # The available mouse protocols types that you can set below are: # Auto BusMouse GlidePoint GlidePointPS/2 IntelliMouse IMPS/2 # Logitech Microsoft MMHitTab MMSeries Mouseman MouseManPlusPS/2 # MouseSystems NetMousePS/2 NetScrollPS/2 OSMouse PS/2 SysMouse # ThinkingMouse ThinkingMousePS/2 Xqueue # which is usually a symbolic link to the real device. # Option "Device" "/dev/ttyS0" # Option "Device" "/dev/ttyS1" # When using XQUEUE, comment out the above two lines, and uncomment # the following line. # Option "Protocol" "Xqueue" # Baudrate and SampleRate are only for some Logitech mice. In # almost every case these lines should be omitted. # Option "BaudRate" "9600" # Option "SampleRate" "150" # Emulate3Buttons is an option for 2-button Microsoft mice # Emulate3Timeout is the timeout in milliseconds (default is 50ms) # Option "Emulate3Buttons" # Option "Emulate3Timeout" "50" # ChordMiddle is an option for some 3-button Logitech mice # Option "ChordMiddle" Identifier "Mouse1" Driver "mouse" Option "Protocol" "IMPS/2" Option "ZAXISMapping" "4 5" # The mouse device. The device is normally set to /dev/mouse, Option "Device" "/dev/mouse" # Option "Device" "/dev/psaux" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:0:0" EndSection Section "Screen" Identifier "aticonfig-Screen[0]-0" Device "aticonfig-Device[0]-0" Monitor "aticonfig-Monitor[0]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Титла: Re: Slakware 12.1 - няма звук Публикувано от: nedpetko в Nov 29, 2008, 23:28 Прикачам ти моя xorg.conf от Slackware, че е много редове.
Мишката се оправя много лесно като и смениш протокола на: Код
Кирилицата също е много лесна: Код И звук имам което ме учудва ;) Дай изхода от: Код за твоя непривилигерован потребител Титла: Re: Slakware 12.1 - няма звук Публикувано от: viv1111 в Nov 30, 2008, 00:09 Благодаря на всички, които ми помогнаха и най-вече благодаря, че темата не се обърна в спам. По въпроса с аудиото - не се сетих за програмата Kuser за прибавяне на потребител в група и се лутах да го направя от терминала. Sonyj7, благодаря, че ми каза за нея. Negpetko, преработих моя xorg.conf, след като огледах внимателно твоя и разбрах, че аз на грешно място съм поставял препоръчаните от теб промени. Сега всичко е наред.
|