Аз или съм много тъп или незнам вече какво. Имам следния проблем:
Конфигурирам си pppoe.conf след това си пиша един chap-secrets файл и си пиша потребител и парола вътре. След това слагам на всички редове във options "#" пробвал съм и без да слагам.След всичко това си пиша adsl-start и то ми изписва ...Connected.След това пробвам дали имам нет, нямааа, изчаквам малко и пак няма.Гледам adsl-status и:
adsl-status: Link is up and running on interface ppp0
ppp0      Link encap:Point-to-Point Protocol
          inet addr:83.97.25.95  P-t-P:195.149.248.36  Mask:255.255.255.255
          UP POINTOPOINT RUNNING NOARP MULTICAST  MTU:1480  Metric:1
          RX packets:4 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:3
          RX bytes:34 (34.0 b)  TX bytes:30 (30.0 b)
 
и пакети не се обменят.
Реших да си побликувам и pppoe.conf файла да го прегледате и да ми кажете ако има някаде грешка.
Това е той:
#***********************************************************************
#
# pppoe.conf
#
# Configuration file for rp-pppoe.  Edit as appropriate and install in
# /etc/ppp/pppoe.conf
#
# NOTE: This file is used by the adsl-start, adsl-stop, adsl-connect and
#       adsl-status shell scripts.  It is *not* used in any way by the
#       "pppoe" executable.
#
# Copyright © 2000 Roaring Penguin Software Inc.
#
# This file may be distributed under the terms of the GNU General
# Public License.
#
# LIC: GPL
# $Id: pppoe.conf,v 1.10 2002/04/09 17:28:38 dfs Exp $
#***********************************************************************

# When you configure a variable, DO NOT leave spaces around the "=" sign.

# Ethernet card connected to ADSL modem
ETH='eth0'

# ADSL user name.  You may have to supply "@provider.com"  Sympatico
# users in Canada do need to include "@sympatico.ca"
# Sympatico uses PAP authentication.  Make sure /etc/ppp/pap-secrets
# contains the right username/password combination.
# For Magma, use xxyyzz@magma.ca
USER='petersm'

# Bring link up on demand?  Default is to leave link up all the time.
# If you want the link to come up on demand, set DEMAND to a number indicating
# the idle time after which the link is brought down.
DEMAND=no
#DEMAND=300

# DNS type: SERVER=obtain from server; SPECIFY=use DNS1 and DNS2;
# NOCHANGE=do not adjust.
DNSTYPE=SERVER

# Obtain DNS server addresses from the peer (recent versions of pppd only)
# In old config files, this used to be called USEPEERDNS.  Changed to
# PEERDNS for better Red Hat compatibility
PEERDNS=no

DNS1=ras-pppoe3
DNS2=hd1

# Make the PPPoE connection your default route.  Set to
# DEFAULTROUTE=no if you don't want this.
DEFAULTROUTE=yes

### ONLY TOUCH THE FOLLOWING SETTINGS IF YOU'RE AN EXPERT

# How long adsl-start waits for a new PPP interface to appear before
# concluding something went wrong.  If you use 0, then adsl-start
# exits immediately with a successful status and does not wait for the
# link to come up.  Time is in seconds.
#
# WARNING WARNING WARNING:
#
# If you are using rp-pppoe on a physically-inaccessible host, set
# CONNECT_TIMEOUT to 0.  This makes SURE that the machine keeps trying
# to connect forever after adsl-start is called.  Otherwise, it will
# give out after CONNECT_TIMEOUT seconds and will not attempt to
# connect again, making it impossible to reach.
CONNECT_TIMEOUT=30

# How often in seconds adsl-start polls to check if link is up
CONNECT_POLL=2

# Specific desired AC Name
ACNAME=ras-pppoe3

# Specific desired service name
SERVICENAME=hd1

# Character to echo at each poll.  Use PING="" if you don't want
# anything echoed
PING="."

# File where the adsl-connect script writes its process-ID.
# Three files are actually used:
#   $PIDFILE       contains PID of adsl-connect script
#   $PIDFILE.pppoe contains PID of pppoe process
#   $PIDFILE.pppd  contains PID of pppd process
CF_BASE=`basename $CONFIG`
PIDFILE="/var/run/$CF_BASE-adsl.pid"

# Do you want to use synchronous PPP?  "yes" or "no".  "yes" is much
# easier on CPU usage, but may not work for you.  It is safer to use
# "no", but you may want to experiment with "yes".  "yes" is generally
# safe on Linux machines with the n_hdlc line discipline; unsafe on others.
SYNCHRONOUS=no

# Do you want to clamp the MSS?  Here's how to decide:
# - If you have only a SINGLE computer connected to the ADSL modem, choose
#   "no".
# - If you have a computer acting as a gateway for a LAN, choose "1412".
#   The setting of 1412 is safe for either setup, but uses slightly more
#   CPU power.
CLAMPMSS=1412
#CLAMPMSS=no

# LCP echo interval and failure count.
LCP_INTERVAL=20
LCP_FAILURE=3

# PPPOE_TIMEOUT should be about 4*LCP_INTERVAL
PPPOE_TIMEOUT=80

# Firewalling: One of NONE, STANDALONE or MASQUERADE
FIREWALL=MASQUERADE

# Linux kernel-mode plugin for pppd.  If you want to try the kernel-mode
# plugin, use LINUX_PLUGIN=/etc/ppp/plugins/rp-pppoe.so
LINUX_PLUGIN=

# Any extra arguments to pass to pppoe.  Normally, use a blank string
# like this:
PPPOE_EXTRA=""

# Rumour has it that "Citizen's Communications" with a 3Com
# HomeConnect ADSL Modem DualLink requires these extra options:
# PPPOE_EXTRA="-f 3c12:3c13 -S ISP"

# Any extra arguments to pass to pppd.  Normally, use a blank string
# like this:
PPPD_EXTRA=""


########## DON'T CHANGE BELOW UNLESS YOU KNOW WHAT YOU ARE DOING
# If you wish to COMPLETELY overrride the pppd invocation:
# Example:
# OVERRIDE_PPPD_COMMAND="pppd call dsl"

# If you want adsl-connect to exit when connection drops:
# RETRY_ON_FAILURE=no
 
Искам само да отбележа че съм към HomeLan (Data.bg) и някой от вас ако и той е към тях и види каде ми е проблема да ми каже.

Пускам си аз програмки с winx3 обаче ми излиза само едно X-че горе в десния ъгъл за затваряне на приложението а и като симулирам mirc-ata и ми дава само 4 гадни шрифта.Как да се справя с тези 2 проблема?

Ами .... Аз съм с Линукс и имам доста сериозен проблем с pppoe-то.
Инсталвам си едно pppoe и си пиша adsl-setup след което си въвеждам всичко след което пиша adsl-start и ми изписва
$| . . Connected
$|
И аз така си мисля и като тръгна да си отварям някой сайт и то нямам интернет, а под Windows си имам '>
Като напиша:
$| ifconfig
Ми изписва че има 4 изпратени пакета и 3 приети за начало след което много бавно се сменят с по 2 пакета но нямам никакъв интернет.
Помогнете моля ви '>

Благодаря предварително.

Pisnalo mi e da pisha kato nenormaled za da stane samo edna stranichka ot sait i zatova zapochnah da izpolzvam dreamwaver i mn bih se zaradval ako niakoi ot vas znae alternativna takava programa koiato da raboti pod linux i sashto taka da spodeli s men i drugite hora koito se interesuvat ot tova i roviat iz tozi forum '>

thanks predvaritelno '>

Hora rabotata e slednata.Az sam s rh9 i si installvam i pacheta samba ma niama swat. tarsia si az svaliam si niakva samba i si ia installvam ot tar.gz posle si pisha tam kvoto triabva v /etc/sevice posle tragvam da tarsia /etc/inetd.conf i shto da vidia niama takova '> obache s locate inetd.conf namerih xinetd.conf i si pomislih logi4no 4e e tova i napisah tam kvoto triabva i posle pisha v edin browser localhost:901 i nema nishto help plz '>

Imam 2 problema s bglinux 5.1 mai beshe versiata ako ne se laja.

1.Instalirah si go i za konzola ma nito mojesh da pisjesh na bg v konzolata shtoto izlizat stranni simvoli a i ne mi raboti kakto triabva komandata "mc" zashtoto ot dolo det sa F1, F2, i t.n. nali izpisva koi F za kakvo e obache az nemoga da go prochitam shtoto sega sa mi niakakvi stranni simvoli btw az sam s red hat 9. A ne sam i zapomnil koi F za kakvo e:)

2. po goliamata mi chast ot Linux-a ne e na bg a i kak da go installiram taka che da pisha i s latinskite bukvi ma da mi izliza na bg shtoto az samo na BG ne sam rabotil mnogo i neznam koia bukva na koe kopche e '>

Red Had 9
Zdraveite imam slednia problem:
Znachi kat tragna da razarhiviram neshto i posle da go instaliram kat napisha ./configure i mi izliza che ne se otkriva cc ili tam gcc i niakvi takiva neshta i po toia nachin nemoga da si installna nishto kat naprimer MPlayer i drugi takiva.

Problem 2:
Xmms-a mi neshte da chete mp3ki kvo da go prava?

Problem 3:
BitchX-a mi neshte da go potragva linux-a mai neznae kakav format e shtoto kato go otvoria /home/empty nali det e direktoriata i tam sam si slojil BX-a i mi pokazva che failovete sa samo nekvi hatrishki v smisal niama nikva ikonka prosto ikonkata e chisto bialo pravoagalniche.

Az mislia che niama da e losho da se napravi neshto kato samba obache na bg i s po lesni i pochti minimalni nastroiki '> az razbirase samo go predlagam tova zashtoto sam nachinaesht v Linux-a e ot edna godina se zanimavam s linux i veche 1 mesec se macha da nastroia sambata i nemoga '>

hey i az sam na dostavchik sas lan na ppp0e ma svalih si i az ppp0e i neznam kak da go nastroia az sam kam HomeLan ako si i ti help pls shtoto i az sam go zagazil az go nastroivam ma neznam DNS adresa na servera i ne sam go pisal a i kat mu dam adsl-start pochva da mi dava che niakvi failove ne sa namereni i takiva prostotii az sam s Redhat 9  ako niakoi iziavi jelanie da help che sam go zagazil

hey she mi kajete li kak da podkaram mIRc pod Linux che imam edin script i iskam da go izpolzvam '>

Mersi predvaritelno

Tarsia free shell s ftp triabvat mi maximum 10 MB minimum 4-5MB ako niakoi znae takiva shells pls da spodeli s men '>

Tarsia free shell s ftp triabvat mi maximum 10 MB minimum 4-5MB ako niakoi znae takiva shells pls da spodeli s men '>

Imam malak problem s MPlayer-a '>  Probvam da instalna MPlayer-90-pre9.0 mai taka beshe ta davam mu ./configure --enable-gui --enable-debug=3 posle make v /Gui i posle make install ma mi pishe 4e niamalo skin kato defoult a v direktoriata gui ima niakvi skinove kak da gi instalna i tiah a sashtia e problema i s font-ovete za subtitrite

Neshto nemoga da si installna red hat 8.0 shtoto go svali edin friend ot internet i 5-te diska i biaha v format .iso i toi gi e otvoril s niakva programka i mi gi bodna na HDD sled tova az si gi opekah na diskove i neshto nemojeshe da se bootne sam i zatova si napravih start up disk obache i toi ne pomogna obache go runnah prez DOS i reshih 4e sam uspial no uvi okaza se 4e pri instalaciata me pitashe kade e i az mu posochvam CD to mi pokazva 4e CD-to go niama a fakticheski sam startiral instalacionnoto ot CD-to  Help pls a mopje da e problem i tova 4e pod windows kat gi gledam direktoriite det sa mi otvoreni ot iso i toi moia frend gi e pisal primerno RED HAT 8.0 CD 1 ..2....3..4 i taka si4kite a kat gi gledam prez dos sa RED HAT 8.0 CD 1.ISO i taka natatak da ne da ima problem v tova?

Neshto nemoga da si installna red hat 8.0 shtoto go svali edin friend ot internet i 5-te diska i biaha v format .iso i toi gi e otvoril s niakva programka i mi gi bodna na HDD sled tova az si gi opekah na diskove i neshto nemojeshe da se bootne sam i zatova si napravih start up disk obache i toi ne pomogna obache go runnah prez DOS i reshih 4e sam uspial no uvi okaza se 4e pri instalaciata me pitashe kade e i az mu posochvam CD to mi pokazva 4e CD-to go niama a fakticheski sam startiral instalacionnoto ot CD-to '> Help pls a mopje da e problem i tova 4e pod windows kat gi gledam direktoriite det sa mi otvoreni ot iso i toi moia frend gi e pisal primerno RED HAT 8.0 CD 1 ..2....3..4 i taka si4kite a kat gi gledam prez dos sa RED HAT 8.0 CD 1.ISO i taka natatak da ne da ima problem v tova?