Автор Тема: Lilo help  (Прочетена 1778 пъти)

3v1

  • Напреднали
  • *****
  • Публикации: 180
    • Профил
Lilo help
« -: Jan 24, 2008, 16:08 »
при инсталация на Debian си сложих бозата да ми е в списък на лило , но след инсталация направо ми зарежда линукса. едитнах си lilo.conf в този вид:
Примерен код

# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# ---------------       `install-mbr(8)', `/usr/share/doc/lilo/',
#                       and `/usr/share/doc/mbr/'.

# +---------------------------------------------------------------+
# |                        !! Reminder !!                         |
# |                                                               |
# | Don't forget to run `lilo' after you make changes to this     |
# | conffile, `/boot/bootmess.txt' (if you have created it), or   |
# | install a new kernel.  The computer will most likely fail to  |
# | boot if a kernel-image post-install script or you don't       |
# | remember to run `lilo'.                                       |
# |                                                               |
# +---------------------------------------------------------------+

# Specifies the boot device.  This is where Lilo installs its boot
# block.  It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/sda

# Specifies the device that should be mounted as root. (`/')
#
root=/dev/sda2

# This option may be needed for some software RAID installs.
#
# raid-extra-boot=mbr-only

# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller.  Using `compact' is especially recommended when
# booting from a floppy disk.  It is disabled here by default
# because it doesn't always work.
#
# compact

# Installs the specified file as the new boot sector
# You have the choice between: text, bmp, and menu
# Look in lilo.conf(5) manpage for details
#
#install=menu

# Specifies the location of the map file
#
map=/boot/map

# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration.  If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well.  Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000

# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=20

# You can put a customized boot message up if you like.  If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress.  `single-key' goes with the `alias' lines in the
# `image' configurations below.  eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
# message=/boot/bootmess.txt
#   prompt
#   delay=10
#   timeout=10

# Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>)
#
# vga=ask
# vga=9
#


# Kernel command line options that apply to all installed images go
# here.  See: The `boot-prompt-HOWTO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""
 
# If you used a serial console to install Debian, this option should be
# enabled by default.
# serial=

#
#
#


image=/vmlinuz
   label=Linux
   read-only
#   restricted
#   alias=1
   initrd=/initrd.img
image=/vmlinuz.old
   label=LinuxOLD
   read-only
   optional
#   restricted
#   alias=2
   initrd=/initrd.img.old
other=/dev/sda1
   label=Windows1
#   restricted
#   alias=2

# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
#   label=HURD
#   restricted
#   alias=3
other=/dev/sda3
   label=Windows
#   restricted
#   alias=2
other=/dev/sda1
   label=Windows1
#   restricted
#   alias=2

windows-a  ми е на /sda1 . някъкви идеи къде бъркам?
ето и изход от fdisk -l
Примерен код

   Device Boot      Start         End      Blocks   Id  System
/dev/sda1   *           1        2615    21004956    7  HPFS/NTFS
/dev/sda2            2616        5282    21422677+  83  Linux
/dev/sda3            5283       30140   199671885    b  W95 FAT32
/dev/sda4           30141       30401     2096482+  82  Linux swap / Solaris




Активен

Gruntz

  • Напреднали
  • *****
  • Публикации: 67
    • Профил
Lilo help
« Отговор #1 -: Jan 24, 2008, 17:05 »
Не съм сигурен, но:

пробвай да разкоментирш "# prompt", да стане само "prompt".
Активен

3v1

  • Напреднали
  • *****
  • Публикации: 180
    • Профил
Lilo help
« Отговор #2 -: Jan 24, 2008, 17:27 »
не стана. може ли проблема да е в това , че не съм го маунтнал този диск?
Активен

carpo

  • Напреднали
  • *****
  • Публикации: 19
    • Профил
Lilo help
« Отговор #3 -: Jan 24, 2008, 17:48 »
въпрос 1: пусна ли lilo след като редактира файла?
въпрос 2: може и да не съм видял правилно, ама няма ли да е по-добре ако няма секции със една и съща информация? (не съм потребител на LILO - аз ползвам GRUB GRUB download site)

Просто мойте 20 ст'инки...

Успех!
 '<img'>



Активен

3v1

  • Напреднали
  • *****
  • Публикации: 180
    • Профил
Lilo help
« Отговор #4 -: Jan 24, 2008, 19:09 »
на първи въпрос , прочетох , че трябва да направя нещо такова , но не знам как. аз си инсталирах и grub
Примерен код

apt-get install grub
grub-install /dev/sda3/

но ми зарежда през лило-то пак .  може би с тия 2-та реда става когато нямам никакъв лоадър.



Активен

Gruntz

  • Напреднали
  • *****
  • Публикации: 67
    • Профил
Lilo help
« Отговор #5 -: Jan 24, 2008, 19:22 »
Когато направиш промени в lilo.conf, трябва да изпълниш командата "lilo" като root, за да се презапише boot сектора. Чак след това промените ти в lilo.conf влизат в сила.

Успех.
Активен

3v1

  • Напреднали
  • *****
  • Публикации: 180
    • Профил
Lilo help
« Отговор #6 -: Jan 24, 2008, 19:28 »
не става
Примерен код

bash: lilo: command not found
Активен

sak81

  • Напреднали
  • *****
  • Публикации: 22
    • Профил
Lilo help
« Отговор #7 -: Jan 25, 2008, 16:48 »
Цитат (3v1 @ Ян. 24 2008,20:28)
не става
Примерен код

bash: lilo: command not found

с root ли изпълняваш командата?
Активен

Подобни теми
Заглавие Започната от Отговора Прегледи Последна публикация
lilo i MBR
Настройка на програми
marinov 2 3153 Последна публикация Apr 21, 2002, 12:35
от pau4o
Lilo+XP
Настройка на програми
mil_dim 4 3181 Последна публикация May 03, 2002, 05:35
от mil_dim
lilo
Настройка на програми
mozly 2 1971 Последна публикация Nov 28, 2002, 22:46
от
LILO
Хардуерни и софтуерни проблеми
ivo3d 8 2987 Последна публикация Aug 05, 2003, 13:29
от ivo3d
LILO
Настройка на програми
azzz 4 1864 Последна публикация Jan 25, 2004, 12:35
от