Последните мнения на: nix

Здр

'>Проблема ми е следния,ползвам debian unstable,и след поредният #apt-get update && apt-get upgrade,лилото ми не пожела да бутне ;( Дава ми следното :
blank screen
LI
Пускам си boot:rescbf24 root=/dev/hda7 ,бутвам нормално пускам си #dpkg-reconfigure lilo,отварям си /etc/lilo.conf
ето го и него ако ще помогне!?!?Ама нищо не разбирам,защо?какво? му пречи да трагне ;(Лилото ми е инсталирано върху боотсектора /dev/hda7,за боот ползвам друг боотлоадер/XOSL/.Ако някой е имал подобен проблем help plss.

Цитат

# /etc/lilo.conf - See: `lilo(

' and `lilo.conf(5)',
# --------------- `install-mbr(

', `/usr/share/doc/lilo/',
# and `/usr/share/doc/mbr/'.

# +---------------------------------------------------------------+
# | !! Reminder !! |
# | |
# | Don't forget to run `lilo' after you make changes to this |
# | conffile, `/boot/bootmess.txt', or install a new kernel. The |
# | computer will most likely fail to boot if a kernel-image |
# | post-install script or you don't remember to run `lilo'. |
# | |
# +---------------------------------------------------------------+

# Support LBA for large hard disks.
#
lba32

# Overrides the default mapping between harddisk names and the BIOS'
# harddisk order. Use with caution.
#disk=/dev/hde
# bios=0x81

#disk=/dev/sda
# bios=0x80

# Specifies the boot device. This is where Lilo installs its boot
# block. It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hda7

# Specifies the device that should be mounted as root. (`/'

'>
#
root=/dev/hda7

# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller. Using `compact' is especially recommended when
# booting from a floppy disk. It is disabled here by default
# because it doesn't always work.
#
# compact

# Installs the specified file as the new boot sector
# You have the choice between: bmp, compat, menu and text
# Look in /boot/ and in lilo.conf(5) manpage for details
#
install=/boot/boot-menu.b

# Specifies the location of the map file
#
map=/boot/map

# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration. If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well. Please RTFM `install-mbr(

'.
#
# password=tatercounter2000

# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=20

# You can put a customized boot message up if you like. If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress. `single-key' goes with the `alias' lines in the
# `image' configurations below. eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
# message=/boot/bootmess.txt
prompt
timeout=150
#   prompt
#   single-key
#   delay=100
#   timeout=100

# Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>)
#
# vga=ask
# vga=9
#
vga=normal

# Kernel command line options that apply to all installed images go
# here. See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""

# Boot up Linux by default.
#
default=Linux

image=/vmlinuz
   label=Linux
   read-only
#   restricted
#   alias=1

image=/vmlinuz.old
   label=LinuxOLD
   read-only
   optional
#   restricted
#   alias=2

# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
#   label=HURD
#   restricted
#   alias=3
other=/dev/hda2
  label="Win/DOS(hda2)"

other=/dev/hda3
  label="WinNT(hda3)"

other=/dev/hda5
  label="WinNT(hda5)"