Титла: Kak da si sloja drivera na Video-to GForce2MX?
Публикувано от: Al_Kapone в Mar 26, 2004, 13:21
Absoliutno na4inaesht sym. Linux-a mi e SuSe 8.2. Izteglih ot stranicata na NVidia tozi driver-"NVIDIA-Linux-x86-1.0-5336-pkg1.run"
Obache za SuSe imashe dopylnitelno readme da pro4eta:
--------
This document describes how to use the new nvidia installer for the
installation of the latest nvidia driver, which is available for your
SuSE Linux system.
"NOTE: The nvidia installer does not work as long as a Xserver is still
running and the nvidia kernel module is still loaded. Therefore
please boot into runlevel 3 by specifying "3" as kernel boot
option or switch to runlevel 3 ("init 3") and unload the kernel
module ("rmmod nvidia") before running the nvidia installer.
SuSE Linux 8.2
SuSE Linux Desktop (SLD)
----------------------------
1) Kernel sources must be installed and configured. Usually this means
installing the 'kernel-source' package with YaST2, update it - if not
already done - via YaST2 Online Update (YOU) and configure it then
with the following commands:
cd /usr/src/linux
make cloneconfig && make dep
2) Use the nvidia installer for 1.0-5336.
sh NVIDIA-Linux-x86-1.0-5336-pkg1.run
3) Configure XFree86 with
sax2 -m 0=nvidia (0 is a digit, not a letter!
NOTE: There is no need to try to enable 3D support. It's already
enabled, when the nvidia driver is running. Ignore the
misleading error message, that 3D support can't be enabled.
This problem will be fixed with SuSE > 9.0 and is related to the
latest nvidia driver release."
Ne znam mai neshto ne e "standartna" instalaciata na tozi driver, niqkoi moje li da mi pomogne?
Obache za SuSe imashe dopylnitelno readme da pro4eta:
--------
This document describes how to use the new nvidia installer for the
installation of the latest nvidia driver, which is available for your
SuSE Linux system.
"NOTE: The nvidia installer does not work as long as a Xserver is still
running and the nvidia kernel module is still loaded. Therefore
please boot into runlevel 3 by specifying "3" as kernel boot
option or switch to runlevel 3 ("init 3") and unload the kernel
module ("rmmod nvidia") before running the nvidia installer.
SuSE Linux 8.2
SuSE Linux Desktop (SLD)
----------------------------
1) Kernel sources must be installed and configured. Usually this means
installing the 'kernel-source' package with YaST2, update it - if not
already done - via YaST2 Online Update (YOU) and configure it then
with the following commands:
cd /usr/src/linux
make cloneconfig && make dep
2) Use the nvidia installer for 1.0-5336.
sh NVIDIA-Linux-x86-1.0-5336-pkg1.run
3) Configure XFree86 with
sax2 -m 0=nvidia (0 is a digit, not a letter!
NOTE: There is no need to try to enable 3D support. It's already
enabled, when the nvidia driver is running. Ignore the
misleading error message, that 3D support can't be enabled.
This problem will be fixed with SuSE > 9.0 and is related to the
latest nvidia driver release."
Ne znam mai neshto ne e "standartna" instalaciata na tozi driver, niqkoi moje li da mi pomogne?
Титла: Kak da si sloja drivera na Video-to GForce2MX?
Публикувано от: AcidSouL в Mar 26, 2004, 20:19
trqqq da ne si pod x...ina4e nqq da stane...i trqq si root....
pi6e6 --> sh NVIDIA-Linux-x86-1.0-5336-pkg1.run
installva6 tam....i posle reboot....
posle trqq si prepravi6 XF86config
/etc/x11/......
tam deto pi6e Driver "n" ili "vesa" go pravi6 na "nvidia"
mai tei be6e :
pi6e6 --> sh NVIDIA-Linux-x86-1.0-5336-pkg1.run
installva6 tam....i posle reboot....
posle trqq si prepravi6 XF86config
/etc/x11/......
tam deto pi6e Driver "n" ili "vesa" go pravi6 na "nvidia"
mai tei be6e :
Титла: Kak da si sloja drivera na Video-to GForce2MX?
Публикувано от: Al_Kapone в Mar 26, 2004, 22:23
huh, tova i az go shvanah, samo 4e ne znam kak da startiram SuSe-to bez grafichnata sreda... i syotvetno kato instalna driver-a da moga pak da ia pusna de 
Титла: Kak da si sloja drivera na Video-to GForce2MX?
Публикувано от: zazzko в Mar 27, 2004, 00:45
telinit 3 или telinit 1. Това като root. След това telinit 4.
Титла: Kak da si sloja drivera na Video-to GForce2MX?
Публикувано от: Al_Kapone в Mar 27, 2004, 11:49
Tova pyk kakvo e?
Титла: Kak da si sloja drivera na Video-to GForce2MX?
Публикувано от: sebastianz55 в Mar 27, 2004, 11:51
в конзолата го пишеш...
Титла: Kak da si sloja drivera na Video-to GForce2MX?
Публикувано от: Al_Kapone в Mar 27, 2004, 11:52
Taka ili ina4e az uspiah da go sloja driver-a, no vse pak kakakvo pravi tova?