Последните мнения на: creo

§б§в§а§Т§У§С§Ы §г §д§а§У§С

lsusb
to get the output somewhat like this
ankur@ankur-desktop:~$ lsusb
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 002: ID 0421:042d Nokia Mobile Phones
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
Notice the ID 0421:042d Nokia Mobile Phones here 421 is the VID and 42d is the PID replace them with what is shown in your case below. Now run the command
sudo /sbin/modprobe usbserial vendor=0x(vid) product=0x(pid)
Like Ў°sudo /sbin/modprobe usbserial vendor=0ЎБ421 product=0ЎБ42dЎ± in my case
then run the following command
wvdialconf create
To get the following output
ankur@ankur-desktop:~$ sudo wvdialconf create
Scanning your serial ports for a modem.
Port Scan: S0 S1 S2 S3
WvModem: Cannot get information for serial port.
ttyACM0: ATQ0 V1 E1 ЎЄ OK
ttyACM0: ATQ0 V1 E1 Z ЎЄ OK
ttyACM0: ATQ0 V1 E1 S0=0 ЎЄ OK
ttyACM0: ATQ0 V1 E1 S0=0 &C1 ЎЄ OK
ttyACM0: ATQ0 V1 E1 S0=0 &C1 &D2 ЎЄ OK
ttyACM0: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 ЎЄ OK
ttyACM0: Modem Identifier: ATI ЎЄ Nokia
ttyACM0: Speed 4800: AT ЎЄ OK
ttyACM0: Speed 9600: AT ЎЄ OK
ttyACM0: Speed 19200: AT ЎЄ OK
ttyACM0: Speed 38400: AT ЎЄ OK
ttyACM0: Speed 57600: AT ЎЄ OK
ttyACM0: Speed 115200: AT ЎЄ OK
ttyACM0: Speed 230400: AT ЎЄ OK
ttyACM0: Speed 460800: AT ЎЄ OK
ttyACM0: Max speed is 460800; that should be safe.
ttyACM0: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 ЎЄ OK
Found an USB modem on /dev/ttyACM0.
Modem configuration written to create.
ttyACM0: Speed 460800; init Ў°ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0Ўе
This shows that a modem is connected at /dev/ttyACM0, Now substitute this at (your modem) in the script below
Enter the command
sudo gedit etc/wvdial.conf
delete any thing already written there and place this in that
[Dialer Defaults]
Modem = (your modem)
Baud = 230400
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ISDN = 0
Modem Type = Analog Modem
Phone = *99***1#
Username = A
Password = B
Stupid Mode = 1
All done now to connect open terminal and type sudo wvdial and you are connected with the following outputankur@ankur-desktop:~$ sudo wvdial
Password:
ЁC> WvDial: Internet dialer version 1.56
ЁC> Cannot get information for serial port.
ЁC> Initializing modem.
ЁC> Sending: ATZ
ATZ
OK
ЁC> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
ЁC> Modem initialized.
ЁC> Sending: ATDT*99***1#
ЁC> Waiting for carrier.
ATDT*99***1#
CONNECT
~[7f]}#@!}!} } }2}#}$@#}!}$}%\}Ў±}&} }*} } g}%~
ЁC> Carrier detected. Starting PPP immediately.
ЁC> Starting pppd at Sat May 26 23:56:24 2007
ЁC> Pid of pppd: 5682
ЁC> Using interface ppp0
ЁC> pppd: [06][06][08]` [06][08]
ЁC> pppd: [06][06][08]` [06][08]
ЁC> pppd: [06][06][08]` [06][08]
ЁC> pppd: [06][06][08]` [06][08]
ЁC> pppd: [06][06][08]` [06][08]
ЁC> local IP address 10.190.137.17
ЁC> pppd: [06][06][08]` [06][08]
ЁC> remote IP address 10.6.6.6
ЁC> pppd: [06][06][08]` [06][08]
ЁC> primary DNS address 202.56.230.5
ЁC> pppd: [06][06][08]` [06][08]
ЁC> secondary DNS address 202.56.240.5
ЁC> pppd: [06][06][08]` [06][08] To disconnect press Ctrl+C.