Изпечатай

[Oxy]

Здравейте ползвам днежту линукс и имам вградена интелска видеокарта, и реших да сложа 3д за да се погъзаря и аз малко... следвах следния туториал http://www.gentoo.org/doc/en/dri-howto.xml и всичко дава ок, glxinfo|grep rendering връща че има директ рендъринг, glxgears се появяват колелцата и се въртят 342.064 FPS ,но пусна ли някакъв компосинг или 3д история от типа на куейк 3 и започва да сече като не знам какво... пробвах да подкарам и куулирис, но пак същата история не може и не може да работи без да сече нормално... в КДЕ има една джаджа блумарбъл , тя пък ми казва че няма opengl shaders ... някакви идеи как да се справя с това ?

00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrated Graphics Controller (rev 02)

[victim70]

И аз имам подобен проблем с гентото АТИ карта и колелцата са добре
Това е след стартиране по подразбиране
16789 frames in 5.0 seconds = 3357.633 FPS
17167 frames in 5.0 seconds = 3433.359 FPS
14725 frames in 5.0 seconds = 2944.991 FPS
15842 frames in 5.1 seconds = 3117.091 FPS
3254 frames in 5.0 seconds = 650.454 FPS
Тука е на пълен екран
1038 frames in 5.0 seconds = 207.506 FPS
854 frames in 5.0 seconds = 170.640 FPS
843 frames in 5.0 seconds = 168.474 FPS
859 frames in 5.0 seconds = 171.731 FPS
854 frames in 5.0 seconds = 170.779 FPS
858 frames in 5.0 seconds = 171.404 FPS
850 frames in 5.0 seconds = 169.960 FPS
855 frames in 5.0 seconds = 170.828 FPS
853 frames in 5.0 seconds = 170.452 FPS
Обаче като пусна ефектите на KDE имам чуството че си минават през процесора твърдо 90% натоварване.
Игри с 3Д също накъсват - не много ама накъсват.
Varicad демото се движи също на пресекулки.
Дуал хед с TV не тръгва защото работи само с затворения драйвер а в него са спрели подръжката на ати 9200. Стария не се компилира с нов кернел. Абе лоша работа 

[Oxy]

блаа никой ли нищо не знае... значи имам модулуте дрм и и810 в кернела, лсмод ми ги показва, хорг.конф-а и там уж всичко е ок :

Код:

# File generated by xorgconfig.        

#
# Copyright 2004 The X.Org Foundation
#                                    
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation 
# the rights to use, copy, modify, merge, publish, distribute, sublicense,  
# and/or sell copies of the Software, and to permit persons to whom the     
# Software is furnished to do so, subject to the following conditions:      
#                                                                           
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.                       
#                                                                           
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,  
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL  
# The X.Org Foundation BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, 
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF 
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE    
# SOFTWARE.                                                                 
#                                                                           
# Except as contained in this notice, the name of The X.Org Foundation shall
# not be used in advertising or otherwise to promote the sale, use or other 
# dealings in this Software without prior written authorization from        
# The X.Org Foundation.                                                     
#                                                                           

# **********************************************************************
# Refer to the xorg.conf(5) man page for details about the format of    
# this file.                                                            
# **********************************************************************

# **********************************************************************
# Module section -- this  section  is used to specify                   
# which dynamically loadable modules to load.                           
# **********************************************************************
#                                                                       
Section "Module"                                                        

# This loads the DBE extension module.

    Load        "dbe"   # Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
    SubSection  "extmod"                                         
      Option    "omit xfree86-dga"   # don't initialise the DGA extension
    EndSubSection                                                        

# This loads the font modules
#    Load        "type1"     
    Load        "freetype"   
#    Load        "xtt"       

# This loads the GLX module
    Load       "glx"       
# This loads the DRI module
    Load       "dri"       

EndSection

# **********************************************************************
# Files section.  This allows default font and rgb paths to be set      
# **********************************************************************

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.                                     

#    RgbPath    "/usr/share/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath  
# command (or a combination of both methods)                              
#                                                                         
#                                                                         

    FontPath   "/usr/share/fonts/misc/"
#    FontPath   "/usr/share/fonts/TTF/"
#    FontPath   "/usr/share/fonts/OTF" 
    FontPath   "/usr/share/fonts/Type1/"
    FontPath   "/usr/share/fonts/100dpi/"
    FontPath   "/usr/share/fonts/75dpi/" 
#    FontPath   "/usr/lib/X11/fonts/local/"
#    FontPath   "/usr/lib/X11/fonts/misc/" 
#    FontPath   "/usr/lib/X11/fonts/75dpi/:unscaled"
#    FontPath   "/usr/lib/X11/fonts/100dpi/:unscaled"
#    FontPath   "/usr/lib/X11/fonts/Speedo/"         
#    FontPath   "/usr/lib/X11/fonts/Type1/"          
#    FontPath   "/usr/lib/X11/fonts/TrueType/"       
#    FontPath   "/usr/lib/X11/fonts/freefont/"       
#    FontPath   "/usr/lib/X11/fonts/75dpi/"          
#    FontPath   "/usr/lib/X11/fonts/100dpi/"         

# The module search path.  The default path is shown here.

#    ModulePath "/usr/lib/modules"

EndSection

# **********************************************************************
# Server flags section.                                                 
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is 
# received.  This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging  

#    Option "NoTrapSignals"

# Uncomment this to disable the <Ctrl><Alt><Fn> VT switch sequence
# (where n is 1 through 12).  This allows clients to receive these key
# events.                                                             

#    Option "DontVTSwitch"

# Uncomment this to disable the <Ctrl><Alt><BS> server abort sequence
# This allows clients to receive this key event.                     

    Option "DontZap"

# Uncomment this to disable the <Ctrl><Alt><KP_+>/<KP_-> mode switching
# sequences.  This allows clients to receive these key events.         

#    Option "Dont Zoom"

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will    
# receive a protocol error.                                         

#    Option "DisableVidModeExtension"

# Uncomment this to enable the use of a non-local xvidtune client. 

#    Option "AllowNonLocalXvidtune"

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.                                  

#    Option "DisableModInDev"

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

#    Option "AllowNonLocalModInDev"

EndSection

# **********************************************************************
# Input devices                                                         
# **********************************************************************

# **********************************************************************
# Core keyboard's InputDevice section                                   
# **********************************************************************

Section "InputDevice"

    Identifier  "Keyboard1"
    Driver      "kbd"      

# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),         
# uncomment the following line.                                        

#    Option     "Protocol"      "Xqueue"

    Option "AutoRepeat" "500 30"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
#    Option     "Xleds"      "1 2 3"                                   

#    Option "LeftAlt"     "Meta"
#    Option "RightAlt"    "ModeShift"

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults).  For example, for a non-U.S.
# keyboard, you will probably want to use:                          
#    Option "XkbModel"    "pc105"                                   
# If you have a US Microsoft Natural keyboard, you can use:         
#    Option "XkbModel"    "microsoft"                               
#                                                                   
# Then to change the language, change the Layout setting.           
# For example, a german layout can be obtained with:                
#    Option "XkbLayout"   "de"                                      
# or:                                                               
#    Option "XkbLayout"   "de"                                      
#    Option "XkbVariant"  "nodeadkeys"                              
#                                                                   
# If you'd like to switch the positions of your capslock and        
# control keys, use:                                                
#    Option "XkbOptions"  "ctrl:swapcaps"                           

# These are the default XKB settings for Xorg
#    Option "XkbRules"    "xorg"             
#    Option "XkbModel"    "pc105"            
#    Option "XkbLayout"   "us"               
#    Option "XkbVariant"  ""                 
#    Option "XkbOptions"  ""                 

#    Option "XkbDisable"

    Option "XkbRules"   "xorg"
    Option "XkbModel"   "pc104"
    Option "XkbLayout"  "en"   

EndSection


# **********************************************************************
# Core Pointer's InputDevice section                                    
# **********************************************************************

Section "InputDevice"

# Identifier and driver

    Identifier  "Mouse1"
    Driver      "mouse" 
    Option "Protocol"    "Auto" # Auto detect
    Option "Device"      "/dev/input/mice"   

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.                                              

#    Option "Protocol"  "Xqueue"

# Mouse-speed setting for PS/2 mouse.

#    Option "Resolution"        "256"

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.           

#    Option "BaudRate"  "9600"
#    Option "SampleRate"        "150"

# Mouse wheel mapping.  Default is to map vertical wheel to buttons 4 & 5,
# horizontal wheel to buttons 6 & 7.   Change if your mouse has more than 
# 3 buttons and you need to map the wheel to different button ids to avoid
# conflicts.                                                              

    Option "ZAxisMapping"   "4 5 6 7"

# Emulate3Buttons is an option for 2-button mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

#    Option "Emulate3Buttons"
#    Option "Emulate3Timeout"    "50"

# ChordMiddle is an option for some 3-button Logitech mice

#    Option "ChordMiddle"

EndSection


# **********************************************************************
# Other input device sections                                           
# this is optional and is required only if you                          
# are using extended input devices.  This is for example only.  Refer   
# to the xorg.conf man page for a description of the options.           
# **********************************************************************
#                                                                       
# Section "InputDevice"                                                 
#    Identifier  "Mouse2"                                               
#    Driver      "mouse"                                                
#    Option      "Protocol"      "MouseMan"                             
#    Option      "Device"        "/dev/mouse2"                          
# EndSection                                                            
#                                                                       
# Section "InputDevice"                                                 
#    Identifier "spaceball"                                             
#    Driver     "magellan"                                              
#    Option     "Device"        "/dev/cua0"                             
# EndSection                                                            
#                                                                       
# Section "InputDevice"                                                 
#    Identifier "spaceball2"                                            
#    Driver     "spaceorb"                                              
#    Option     "Device"        "/dev/cua0"                             
# EndSection                                                            
#                                                                       
# Section "InputDevice"                                                 
#    Identifier "touchscreen0"                                          
#    Driver     "microtouch"                                            
#    Option     "Device"        "/dev/ttyS0"                            
#    Option     "MinX"          "1412"                                  
#    Option     "MaxX"          "15184"                                 
#    Option     "MinY"          "15372"                                 
#    Option     "MaxY"          "1230"                                  
#    Option     "ScreenNumber"  "0"                                     
#    Option     "ReportingMode" "Scaled"                                
#    Option     "ButtonNumber"  "1"                                     
#    Option     "SendCoreEvents"                                        
# EndSection                                                            
#                                                                       
# Section "InputDevice"                                                 
#    Identifier "touchscreen1"                                          
#    Driver     "elo2300"                                               
#    Option     "Device"        "/dev/ttyS0"                            
#    Option     "MinX"          "231"                                   
#    Option     "MaxX"          "3868"                                  
#    Option     "MinY"          "3858"                                  
#    Option     "MaxY"          "272"                                   
#    Option     "ScreenNumber"  "0"                                     
#    Option     "ReportingMode" "Scaled"                                
#    Option     "ButtonThreshold"       "17"                            
#    Option     "ButtonNumber"  "1"                                     
#    Option     "SendCoreEvents"                                        
# EndSection                                                            

# **********************************************************************
# Monitor section                                                       
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

    Identifier  "syncmaster"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.                       
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.                             

    HorizSync   31.5 - 64

#    HorizSync  30-64         # multisync
#    HorizSync  31.5, 35.2    # multiple fixed sync frequencies
#    HorizSync  15-25, 30-50  # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.                         
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S 
# USER MANUAL FOR THE CORRECT NUMBERS.                              

    VertRefresh 50-90

EndSection


# **********************************************************************
# Graphics device section                                               
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
    Identifier  "Standard VGA"
    VendorName  "Unknown"     
    BoardName   "Unknown"     

# The chipset line is optional in most cases.  It can be used to override
# the driver's chipset detection, and should not normally be specified.  

#    Chipset    "generic"

# The Driver line must be present.  When using run-time loadable driver
# modules, this line instructs the server to load the specified driver 
# module.  Even when not using loadable driver modules, this line      
# indicates which driver should interpret the information in this section.

    Driver     "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for.  When this line isn't present, a device
# section can only match up with the primary video device.  For PCI    
# devices a line like the following could be used.  This line should not
# normally be included unless there is more than one video device       
# intalled.                                                             

#    BusID      "PCI:0:10:0"

#    VideoRam   256

#    Clocks     25.2 28.3

EndSection

# Device configured by xorgconfig:

Section "Device"
    Identifier  "intel vga"
    Driver      "intel"    
    Option "AGPMode" "4"   
    Option      "AccelMethod" "EXA"
    Option      "RenderAccel" "true"
    Option      "EnablePageFlip" "true"
    Option      "MigrationHeuristic" "greedy"
    Option      "ExaNoComposite" "false"     

    #VideoRam    65536
    # Insert Clocks lines here if appropriate
EndSection                                   


# **********************************************************************
# Screen sections                                                       
# **********************************************************************

# Any number of screen sections may be present.  Each describes
# the configuration of a single screen.  A single specific screen section
# may be specified from the X server command line with the "-screen"     
# option.                                                                
Section "Screen"                                                         
    Identifier  "Screen 1"                                               
    Device      "intel vga"                                              
    Monitor     "syncmaster"                                             
    DefaultDepth 24                                                      

    Subsection "Display"
        Depth       8
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       16
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       24
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present.  Each describes
# the way multiple screens are organised.  A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option.  In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
    Identifier  "Simple Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens.  The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen.  In this example, screen 2 is located to the
# right of screen 1.

    Screen "Screen 1"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used.  Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

    InputDevice "Mouse1" "CorePointer"
    InputDevice "Keyboard1" "CoreKeyboard"

EndSection

 Section "DRI"
    Mode 0666
 EndSection