Изпечатай

[Gruntz]

Здравейте.

Не мога да монтирам никакво USB устроиство на Slackawre 11. Имам едно flash drive, което не мога да монтирам. Примирих се с това, но сега имаме един usb mp3-player, и с него имам същият проблем. Разполагам с 4 USB устроиства разположени на една PCI платка. Преди имах едно usb портче вързано с кабел за usb конектор на дънната платка, тогава всичко работеше, но портчето изгоря. Откакто съм с платката с usb портовете, неработи.

Ето какво ми дава в /var/log/messages

Примерен код

... Jun  6 23:51:20 tangra kernel: shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 Jun  6 23:51:21 tangra kernel: USB Universal Host Controller Interface driver v3.0 Jun  6 23:51:21 tangra kernel: uhci_hcd 0000:00:07.2: UHCI Host Controller Jun  6 23:51:21 tangra kernel: uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1 Jun  6 23:51:21 tangra kernel: uhci_hcd 0000:00:07.2: irq 11, io base 0x00006400 Jun  6 23:51:21 tangra kernel: usb usb1: configuration #1 chosen from 1 choice Jun  6 23:51:21 tangra kernel: hub 1-0:1.0: USB hub found Jun  6 23:51:21 tangra kernel: hub 1-0:1.0: 2 ports detected Jun  6 23:51:21 tangra kernel: PCI: Found IRQ 10 for device 0000:00:10.0 Jun  6 23:51:21 tangra kernel: uhci_hcd 0000:00:10.0: UHCI Host Controller Jun  6 23:51:21 tangra kernel: uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2 Jun  6 23:51:21 tangra kernel: uhci_hcd 0000:00:10.0: irq 10, io base 0x00006c00 Jun  6 23:51:21 tangra kernel: usb usb2: configuration #1 chosen from 1 choice Jun  6 23:51:21 tangra kernel: hub 2-0:1.0: USB hub found Jun  6 23:51:21 tangra kernel: hub 2-0:1.0: 2 ports detected Jun  6 23:51:21 tangra kernel: PCI: Found IRQ 10 for device 0000:00:10.1 Jun  6 23:51:21 tangra kernel: PCI: Sharing IRQ 10 with 0000:00:12.0 Jun  6 23:51:21 tangra kernel: uhci_hcd 0000:00:10.1: UHCI Host Controller Jun  6 23:51:21 tangra kernel: uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3 Jun  6 23:51:21 tangra kernel: uhci_hcd 0000:00:10.1: irq 10, io base 0x00007000 Jun  6 23:51:21 tangra kernel: usb usb3: configuration #1 chosen from 1 choice Jun  6 23:51:21 tangra kernel: hub 3-0:1.0: USB hub found Jun  6 23:51:21 tangra kernel: hub 3-0:1.0: 2 ports detected Jun  6 23:51:22 tangra kernel: piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device Jun  6 23:51:24 tangra kernel: PCI: Found IRQ 11 for device 0000:00:10.2 Jun  6 23:51:24 tangra kernel: ehci_hcd 0000:00:10.2: EHCI Host Controller Jun  6 23:51:24 tangra kernel: ehci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4 Jun  6 23:51:24 tangra kernel: ehci_hcd 0000:00:10.2: irq 11, io mem 0xe4001000 Jun  6 23:51:24 tangra kernel: ehci_hcd 0000:00:10.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004 Jun  6 23:51:24 tangra kernel: usb usb4: configuration #1 chosen from 1 choice Jun  6 23:51:24 tangra kernel: hub 4-0:1.0: USB hub found Jun  6 23:51:24 tangra kernel: hub 4-0:1.0: 4 ports detected Jun  6 23:51:44 tangra kernel: pnp: Device 00:01.02 activated. Jun  6 23:51:44 tangra kernel: gameport: NS558 PnP Gameport is pnp00:01.02/gameport0, io 0x201, speed 806kHz Jun  6 23:52:23 tangra logger: /etc/rc.d/rc.hotplug start (exiting script) Jun  6 23:56:39 tangra kernel: Initializing USB Mass Storage driver... Jun  6 23:56:39 tangra kernel: usbcore: registered new driver usb-storage Jun  6 23:56:39 tangra kernel: USB Mass Storage support registered.

А това е /var/log/dmesg

Примерен код

Linux version 2.6.18 (root@tree) (gcc version 3.4.6) #1 Wed Sep 20 03:01:24 CDT 2006 BIOS-provided physical RAM map:  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)  BIOS-e820: 0000000000100000 - 000000000c000000 (usable)  BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 192MB LOWMEM available. On node 0 totalpages: 49152   DMA zone: 4096 pages, LIFO batch:0   Normal zone: 45056 pages, LIFO batch:15 DMI 2.0 present. ACPI: Unable to locate RSDP Allocating PCI resources starting at 10000000 (gap: 0c000000:f3ff0000) Detected 262.513 MHz processor. Built 1 zonelists.  Total pages: 49152 Kernel command line: auto BOOT_IMAGE=Linux ro root=301 Initializing CPU#0 PID hash table entries: 1024 (order: 10, 4096 bytes) Console: colour dummy device 80x25 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 191112k/196608k available (2204k kernel code, 5064k reserved, 717k data, 184k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 525.62 BogoMIPS (lpj=1051254) Security Framework v1.0.0 initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0080f9ff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0080f9ff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 512K CPU: After all inits, caps: 0080f9ff 00000000 00000000 00000040 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. CPU: Intel Pentium II (Klamath) stepping 04 Checking 'hlt' instruction... OK. NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfb420, last bus=1 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter disabled. Linux Plug and Play Support v0.97 (c) Adam Belay SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) * Found PM-Timer Bug on the chipset. Due to workarounds for a bug, * this clock source is slow. Consider trying other clock sources PCI quirk: region 4000-403f claimed by PIIX4 ACPI PCI quirk: region 5000-500f claimed by PIIX4 SMB Boot video device is 0000:01:00.0 PCI: Using IRQ router PIIX/ICH [8086/7110] at 0000:00:07.0 PCI: Bridge: 0000:00:01.0   IO window: e000-efff   MEM window: d8000000-dfffffff   PREFETCH window: a8000000-afffffff NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 8192 bind 4096) TCP reno registered apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered Limiting direct PCI/PCI transfers. pci_hotplug: PCI Hot Plug PCI Core version: 0.5 vesafb: framebuffer at 0xa8000000, mapped to 0xcc800000, using 1875k, total 65536k vesafb: mode is 800x600x16, linelength=1600, pages=2 vesafb: protected mode interface info at c000:dfa0 vesafb: pmi: set display start = c00cdfe5, set palette = c00ce06a vesafb: pmi: ports = b4c3 b503 ba03 c003 c103 c403 c503 c603 c703 c803 c903 cc03 ce03 cf03 d003 d103 d203 d303 d403 d503 da03 ff03 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 100x37 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... isapnp: Card 'ESS ES1869 Plug and Play AudioDrive' isapnp: 1 Plug & Play card detected total Real Time Clock Driver v1.12ac Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS3 at I/O 0x2e8 (irq = 3) is a 16550A Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PIIX4: IDE controller at PCI slot 0000:00:07.1 PIIX4: chipset revision 1 PIIX4: not 100% native mode: will probe irqs later     ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio     ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio Probing IDE interface ide0... hda: ST320410A, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: SONY DVD-ROM DDU1211, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 pnp: Device 00:01.03 activated. ide2: generic PnP IDE interface Probing IDE interface ide2... hda: max request size: 128KiB hda: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63, UDMA(33) hda: cache flushes not supported  hda: hda1 hda2 < hda5 hda6 > hdc: ATAPI 40X DVD-ROM drive, 512kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 ide-floppy driver 0.99.newide libata version 2.00 loaded. usbmon: debugfs is not available usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver PNP: No PS/2 controller found. Probing ports directly. serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 TCP bic registered Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode md: Autodetecting RAID arrays. Time: tsc clocksource has been installed. md: autorun ... md: ... autorun DONE. EXT2-fs warning (device hda1): ext2_fill_super: mounting ext3 filesystem as ext2 VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 184k freed input: AT Translated Set 2 keyboard as /class/input/input0 Adding 248968k swap on /dev/hda5.  Priority:-1 extents:1 across:248968k input: PC Speaker as /class/input/input1 input: ImPS/2 Generic Wheel Mouse as /class/input/input2 parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP] parport0: irq 7 detected lp0: using parport0 (polling). lp0: console ready Linux agpgart interface v0.101 (c) Dave Jones 8139too Fast Ethernet driver 0.9.27 PCI: setting IRQ 10 as level-triggered PCI: Found IRQ 10 for device 0000:00:0f.0 eth0: RealTek RTL8139 at 0x6800, 00:c0:26:83:f8:87, IRQ 10 eth0:  Identified 8139 chip type 'RTL-8100B/8139D' PCI: Found IRQ 10 for device 0000:00:12.0 PCI: Sharing IRQ 10 with 0000:00:10.1 eth1: RealTek RTL8139 at 0x7400, 00:00:00:00:00:00, IRQ 10 eth1:  Identified 8139 chip type 'RTL-8100B/8139D' Capability LSM initialized kjournald starting.  Commit interval 5 seconds EXT3 FS on hda6, internal journal EXT3-fs: mounted filesystem with ordered data mode.

Командата lsmod ми дава следното:

Примерен код

Module                  Size  Used by usb_storage            80064  0 vfat                   10240  0 fat                    46108  1 vfat ohci_hcd               18564  0 analog                 10272  0 ns558                   4736  0 gameport               11144  3 analog,ns558 ehci_hcd               29192  0 i2c_piix4               7436  0 uhci_hcd               20748  0 shpchp                 33052  0 intel_agp              19740  1 nvidia               4541396  12 i2c_core               16784  2 i2c_piix4,nvidia ipt_MASQUERADE          2816  3 iptable_mangle          2432  0 iptable_nat             6148  1 ip_nat                 14764  2 ipt_MASQUERADE,iptable_nat ip_conntrack           40596  3 ipt_MASQUERADE,iptable_nat,ip_nat nfnetlink               5272  2 ip_nat,ip_conntrack iptable_filter          2432  0 ip_tables              11480  3 iptable_mangle,iptable_nat,iptable_filter x_tables               10756  3 ipt_MASQUERADE,iptable_nat,ip_tables snd_seq_dummy           2948  0 snd_seq_oss            29056  0 snd_seq_midi_event      6016  1 snd_seq_oss snd_seq                43856  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event snd_pcm_oss            42144  0 snd_mixer_oss          14976  2 snd_pcm_oss snd_es18xx             28648  1 snd_pcm                67720  2 snd_pcm_oss,snd_es18xx snd_page_alloc          7816  1 snd_pcm snd_opl3_lib            8704  1 snd_es18xx snd_timer              19460  3 snd_seq,snd_pcm,snd_opl3_lib snd_hwdep               6788  1 snd_opl3_lib snd_mpu401_uart         6528  1 snd_es18xx snd_rawmidi            18848  1 snd_mpu401_uart snd_seq_device          6540  5 snd_seq_dummy,snd_seq_oss,snd_seq,snd_opl3_lib,snd_rawmidi snd                    42724  12 snd_seq_oss,snd_seq,snd_pcm_oss,snd_mixer_oss,snd_es18xx,snd_pcm,snd_opl3_lib,snd_timer,sn d_hwdep,snd_mpu401_uart,snd_rawmidi,snd_seq_device soundcore               7264  2 snd ipv6                  225248  24 ext3                  120584  1 jbd                    47272  1 ext3 capability              3464  0 commoncap               5504  1 capability 8139too                21632  0 mii                     4992  1 8139too agpgart                28208  2 intel_agp,nvidia lp                      9928  0 parport_pc             24260  1 parport                30152  2 lp,parport_pc pcspkr                  2560  0 psmouse                35464  0

Стартирал съм /etc/rc.d/rc.hotplugin. Пробвам да монтиам устроиството със следната команда:
mount /dev/sda1 /mnt/memory , но ми дава следната грешка:

Примерен код

mount: /dev/sda1 is not a valid block device

Ако трябва да ви дам още информация за системата си, кажете. Благодаря предварително.

Поздрави.

[ivo1204]

Включи нещо в картата ,дай :
fdisk -l
Ако няма нищо , дай :
" lsusb" "lsusb -vt" ,виж какво дава.
Ако пак няма нищо , виж темата за тунера , търси тази карта като pci , дай информацията .

[Gruntz]

fdisc -l дава това:

Примерен код

Disk /dev/hda: 20.0 GB, 20020396032 bytes 255 heads, 63 sectors/track, 2434 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes    Device Boot      Start         End      Blocks   Id  System /dev/hda1               1         747     6000246   83  Linux /dev/hda2             748        2434    13550827+   f  W95 Ext'd (LBA) /dev/hda5             748         778      248976   82  Linux swap /dev/hda6             779        2434    13301788+  83  Linux

hda1 ми е главният дял, hda5 ми е swap дяла, а hda6 ми е дял за данни.

lsusb -vt дава:

Примерен код

Cannot open /proc/bus/usb/devices, No such file or directory (2)

Неразбрах как да търся тази карта като PCI?

lspci дава това:

Примерен код

00:00.0 Host bridge: Intel Corporation 440LX/EX - 82443LX/EX Host bridge (rev 03) 00:01.0 PCI bridge: Intel Corporation 440LX/EX - 82443LX/EX AGP bridge (rev 03) 00:07.0 ISA bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 01) 00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01) 00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01) 00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 01) 00:0f.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 50) 00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 50) 00:10.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 51) 00:12.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 440 AGP 8x] (rev a4)

USB платката ми е на VIA и мисля, че трите USB Constrollers: VIA TEchnologies се отанася точно за нея.

[sonyj7]

Не съм сигурен, но мисля че за usb се зарежда допълнителен модул към ядрото. Обаче не се сещам кой. Виж в usb howto, там трябва да пише.

[Gruntz]

Ами аз уж съм заредил

Примерен код

usb_storage            80064  0

Преди когато не бях с тази платка на VIA с USB-тата а си ползвах това на дъното ( 00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01) ) всичко работеше без проблем. Пусках си hotplugin-а, монтирах си утроиството. Сега не работи.

Известно време няма да мога да използвам интернет. Ако някои има предложения, идей, или се е зблъсквал с проблема, да каже, аз в неделя ще прочета. Благодаря за отзоваванията до сега.

До неделя...

[paucku]

Разни идеи.

— Сигурен ли си, че партишъна на плеъра е sda1, а не примерно само sda?

— Аз бих ти препоръчал да си инсталираш udev. Той прави така че устройствата в /dev/ да се показват само, като са налични.

— Виждам, че е заредил модула ohci_hcd, но при мен е uhci_hcd. Пробвай да го заредиш и него.

— Напиши dmesg, закачи плеъра и пак го напиши и дай последните редове, които е добавил.

— Едно време за USB storage се искаше SCSI емулация. Трябваше да се зареди модула scsi_mod. Може и това да е проблема.

Успех!

[ivo1204]

fdisk -l  ти дава всички налични дискове ( и тези на USB -то ) , но тях ги няма (включи ли нещо в USB-то когато даде командата? ) , няма какво да опитваш с mount  ....
„Cannot open /proc/bus/usb/devices, No such file or directory (2)“ , значи не е монтирана  usbfs(или usbdevfs) в /proc/bus/usb/devices . Нормално се монтира някъде в началото след като е монтирана root , proc ,sys , tmp   в някой rc.хххх (може би rc.local ?, нямам Slackware ) скрипт. Например в Дебиан е в/etc/rcS.d/S02mountkernfs.sh.
Ако имаш udev , даже не ти е и нужно , но отначало ти трябва.
Виж дали твоето ядро подържа usbfs (или usbdevfs):
#cat /proc/filesystems
...........
nodev   usbfs
...................
 
 Опитай да я монтираш:
#mount -t usbfs usbfs /proc/bus/usb   или:
#mount -t usbdevfs usbdevfs /proc/bus/usb

Ако пак не става (lsusb -vt) , може директно да отидеш в „sys“, например в /sys/block/sda , бодни USB и гледай дали
ще се появи /sys/block/sda/sda1/ (ядрото я прави , ама няма да се види  ако не „прзаредиш“ информацията , бутона „презареждане“ или отиди в друга директория и се върни ).
 Може да нямаш  „sda1“ , то си зависи от устройсто което си включил , чети /sys/block/sda/size , като няма е „0“ , иначе е размера.
За всичко това трябва да си „root“ ,мисля че модулите са ти ОК. Начи това ми идва на ум сега , но има и много други .
Например що не пробваш с LiveCD , мисля че проблема е в Слака.

[Archangel]

така при мен начина да разбереш кой /dev/* ми е usb * е
пъхам го и гледам dmesg-a последните 10 реда

Примерен код

$ dmesg | tail sdc: Write Protect is off sdc: Mode Sense: 23 00 00 00 sdc: assuming drive cache: write through SCSI device sdc: 1007616 512-byte hdwr sectors (516 MB) sdc: Write Protect is off sdc: Mode Sense: 23 00 00 00 sdc: assuming drive cache: write through  sdc: [b]sdc1[/b] sd 4:0:0:0: Attached scsi removable disk sdc sd 4:0:0:0: Attached scsi generic sg3 type 0

диска е sdc1

Примерен код

/dev/sdc1 on /media/disk type vfat (rw,nosuid,nodev,uhelper=hal,shortname=lower,uid=500)

при мен лично се маунтват автоматично '>
http://www.linux-consulting.com/Amd_AutoFS/autofs.html
не знам дали ще ти помогне