Автор Тема: ELCON ADSL HELP!  (Прочетена 1155 пъти)

Donislav

  • Участници
  • ***
  • Публикации: 4
    • Профил
ELCON ADSL HELP!
« -: Aug 28, 2004, 14:19 »
Zdravejte
Izvinete me za latinicata no nqmam golqm izbor.
Imam ne malyk problem s edin ot ADSL modemite na BTK - ELCON 131 U na USB. Ako nqkoj e puskal takyv pls help!
Problema e sledniq:
Pyrvo bqh s Slackware 9.1. Slojih si driverite na eagle-usb. Spored men sym vklu4il vsi4ko neobhodimo v qdroto - USB support i t.n.
Kato rygna modema v USB to si zarejda drivera, power-a na modema svetva posle i ADSL lampi4kata. "ifconfig eth1 up" i posle "ifconfig ppp0 up" (imam edna LAN karta na eth0). rezultata ot ifconfig mi e:
lo
eth0
eth1
ppp0

VPI i VCI sym gi nastroil kakto e opisano v forumite koito 4etoh za BTK nastrojki . Imam stati4no IP koeto sym go dal v eagle-usb.conf (probvah i bez da go dam)  
"adsl-setup" - pi6a si Username i passw kakvito sa mi dadeni i drugite nastrojki. NQMAM FIREWALL
/etc/resolv.config davam vytre DNS ite deto mi gi dadaha ot BTC

options mi e iz4isteno

Pri puskane na "pppoe -I eth1 -A" da mi tyrsi Access Concetratora na BTC mi vry6ta "Timeout waiting for PADO packets" . A v log-a e zapisano: Source adress: MAC-a na modema ; Destination adress: ff:ff:ff:ff:ff:ff (broadcast) . Provbah i "tcpdump -i ppp0 | grep ppp" - ni6to ne hva6ta.
Nqmam zadaden DHCP no ne znam dali trqbva - vse pak sym s static IP
Sled tova slojih Slack10 - rezultata e sy6tiq "Timeout waiting for PADO packets"
Sega sym s Knoppix i pak sy6tiq rezultat. Pusnah i ADSL/PPPOE configuration ot X sredata no bez uspeh
Moje li nqkoj da mi kaje kakvo ispuskam ?!
Ve4e iz4etoh vsi4ki forumi ama bez osoben uspeh. Ne sym mn navytre s Linux-a i ako nqkoj se se6ta kakvo izpuskam vseki pyt psl pi6ete 6te byda mn blagodaren
10x in advance
Активен

kennedy

  • Напреднали
  • *****
  • Публикации: 2151
  • Николай Колев
    • Профил
ELCON ADSL HELP!
« Отговор #1 -: Aug 29, 2004, 08:20 »
в пощенския списък на lug-bg имаше подоби 2-3 теми с подробно обяснение. адреса е http://linux-bulgaria.org/
Активен

"за всичко иде час" Еклесиаст 3:1
всеки пост - отговор на въпрос
-----------------
24.12.2003 "MS Free"

  • Гост
ELCON ADSL HELP!
« Отговор #2 -: Aug 29, 2004, 11:59 »
Xmm,
Zashto digash ppp0 interface??
to se diga kato se lognesh v BTK s user i pass ?
svali interfaceto i izpylni
pppoe -I eth1 -A i taka ....
Активен

Donislav

  • Участници
  • ***
  • Публикации: 4
    • Профил
ELCON ADSL HELP!
« Отговор #3 -: Aug 30, 2004, 00:23 »
Blagodarq za otgovorite!
6te provbam bez ppp0 up
BTW s Knoppix -a posledno pri izpylnenie na "pppoe -I eth1 -A" i "tcpdump -i eth1 | grep ppp" mi dade :
2 packets recieved by filter
0 packets droped by kernel

Pak ne se svyrzah.
Kakyv e tozi filter sled kato "iptables --list" mi dava 4e vsi4ki chains sa s politiki ACCEPT!?
Активен

  • Гост
ELCON ADSL HELP!
« Отговор #4 -: Sep 08, 2004, 19:53 »
;-) Когато ти се зарежда драйвера за модема какво ти изписва в системния лог? Прави ли си виртуален ethX? когато напишеш
"eaglestat" дава ли ти накрая: "Modem operational" ?!'<img'> Ако не ти го дава, би трябвало в скобички да ти пише: (eaglectrl -d) или нещо подобно'<img'> Ако ти пише това просто го изпълни!'<img'> След около 10-ина секунди модема трябва да се е вдигнал и да е създал виртуален интерфейс на който да вдигнеш ИП-то'<img'> После адсл-старт и би трябвало да си готов... ! Но за да ти дам точен отговор paste ot syslog-a и от messages, след опита ти за връзка за да мога да ти кажа къде точно е проблема;0 Вече съм пускал 2-3 такива модема за ADSL и 1-2 за ISDN линии към БТК'<img'>
Активен

Donislav

  • Участници
  • ***
  • Публикации: 4
    • Профил
ELCON ADSL HELP!
« Отговор #5 -: Sep 08, 2004, 22:02 »
10х за отговора
Та значи прави ми виртуален eth1 , модема ми е operational, но не мога да се свържа. Пуснах една програмка за анализиране на пакети паралелно - ethereal. Ще пусна резултата и от нея - хваща ми на eth1 пакети от типа PADI но нямам отговор отсреща (PADO) . При "pppoe -I eth1 -A" също не пристига нищо.
Пускам логовете но няма да ги paste целите че се мн големи , освен ако не ги искаш целите:

SYSLOG:

Sep  8 05':0'1:13 router kernel: kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
Sep  8 05':0'1:13 router last message repeated 2 times
Sep  8 05':0'1:13 router kernel:    8regs     :   773.600 MB/sec
Sep  8 05':0'1:13 router kernel:    32regs    :   445.200 MB/sec
Sep  8 05':0'1:13 router kernel:    pII_mmx   :  1059.200 MB/sec
Sep  8 05':0'1:13 router kernel:    p5_mmx    :  1102.800 MB/sec
Sep  8 05':0'1:13 router kernel: raid5: using function: p5_mmx (1102.800 MB/sec)
Sep  8 05':0'1:13 router kernel: VFS: Mounted root (ext3 filesystem) readonly.
Sep  8 05':0'1:14 router cardmgr[76]: no pcmcia driver in /proc/devices
Sep  8 05':0'1:16 router kernel: hw_random: misc device register failed
Sep  8 05':0'1:16 router insmod: /lib/modules/2.4.26/kernel/drivers/char/hw_random.o: init_module: Device or resource busy
Sep  8 05':0'1:16 router insmod: /lib/modules/2.4.26/kernel/drivers/char/hw_random.o: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters.       You may find more information in syslog or the output from dmesg
Sep  8 05':0'1:16 router insmod: /lib/modules/2.4.26/kernel/drivers/char/hw_random.o: insmod hw_random failed
Sep  8 05':0'1:16 router kernel: hw_random: misc device register failed
Sep  8 05':0'1:19 router insmod: /lib/modules/2.4.26/kernel/drivers/char/hw_random.o: init_module: Device or resource busy
Sep  8 05':0'1:19 router insmod: /lib/modules/2.4.26/kernel/drivers/char/hw_random.o: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters.       You may find more information in syslog or the output from dmesg
Sep  8 05':0'1:19 router insmod: /lib/modules/2.4.26/kernel/drivers/char/hw_random.o: insmod hw_random failed
Sep  8 05':0'1:20 router insmod: insmod: a module named eagle-usb already exists
Sep  8 05':0'1:20 router insmod: insmod: insmod eagle-usb failed
Sep  8 05':0'2:26 router smbd[1088]: [2004/09/08 05':0'2:26, 0] printing/print_cups.c:cups_printer_fn(108)
Sep  8 05':0'2:26 router smbd[1088]:   Unable to connect to CUPS server localhost - Connection refused
Sep  8 05':0'4:50 router pppd[1218]: LCP: timeout sending Config-Requests
Sep  8 05':0'4:54 router pppoe[1220]: Timeout waiting for PADO packets

MESSAGES:
Sep  8 05':0'1:14 router logger: /etc/rc.d/rc.inet1:  /sbin/ifconfig lo 127.0.0.1
Sep  8 05':0'1:14 router logger: /etc/rc.d/rc.inet1:  /sbin/route add -net 127.0.0.0 netmask 255.0.0.0 lo
Sep  8 05':0'1:14 router logger: /etc/rc.d/rc.inet1:  /sbin/route add default gw 192.168.1.254 metric 1
Sep  8 05':0'1:14 router logger: SIOCADDRT: Network is unreachable
Sep  8 05':0'1:14 router logger: /etc/rc.d/rc.hotplug start (entering script)
Sep  8 05':0'1:15 router kernel: 8139too Fast Ethernet driver 0.9.26
Sep  8 05':0'1:15 router kernel: PCI: Found IRQ 5 for device 01:0a.0
Sep  8 05':0'1:15 router kernel: eth0: RealTek RTL8139 at 0xc88f5000, 00:50:bf:0f:1b:18, IRQ 5
Sep  8 05':0'1:15 router kernel: eth0: link down
Sep  8 05':0'1:16 router kernel: usb.c: registered new driver usbdevfs
Sep  8 05':0'1:16 router kernel: usb.c: registered new driver hub
Sep  8 05':0'1:16 router kernel: uhci.c: USB Universal Host Controller Interface driver v1.1
Sep  8 05':0'1:16 router kernel: PCI: Found IRQ 6 for device 00:1f.2
Sep  8 05':0'1:16 router kernel: uhci.c: USB UHCI at I/O 0xb400, IRQ 6
Sep  8 05':0'1:16 router kernel: usb.c: new USB bus registered, assigned bus number 1
Sep  8 05':0'1:16 router kernel: hub.c: USB hub found
Sep  8 05':0'1:16 router kernel: hub.c: 2 ports detected
Sep  8 05':0'1:16 router kernel: i810_rng hardware driver 0.9.8 loaded
Sep  8 05':0'1:16 router kernel: hub.c: new USB device 00:1f.2-2, assigned address 2
Sep  8 05':0'1:18 router logger: /etc/rc.d/rc.inet1:  /sbin/iwconfig eth0 nick router
Sep  8 05':0'1:18 router logger: /etc/rc.d/rc.inet1:  /sbin/iwconfig eth0 essid any
Sep  8 05':0'1:18 router logger: /etc/rc.d/rc.inet1:  /sbin/ifconfig eth0 192.168.1.254 broadcast 192.168.1.255 netmask 255.255.255.0
Sep  8 05':0'1:18 router logger: /etc/rc.d/rc.inet1:  /sbin/route add default gw 192.168.1.254 metric 1
Sep  8 05':0'1:20 router kernel: [eagle-usb] driver V1.9.9 loaded
Sep  8 05':0'1:20 router kernel: usb.c: registered new driver eagle-usb
Sep  8 05':0'1:20 router kernel: [eagle-usb] New USB ADSL device detected, waiting for DSP code...
Sep  8 05':0'1:20 router kernel: [eagle-usb] created proc entry at : /proc/driver/eagle-usb/001-002
Sep  8 05':0'1:21 router kernel: usb.c: registered new driver acm
Sep  8 05':0'1:21 router kernel: acm.c: v0.21:USB Abstract Control Model driver for USB modems and ISDN adapters
Sep  8 05':0'1:28 router kernel: [eagle-usb] ioctl EU_IO_OPTIONS received
Sep  8 05':0'1:28 router logger: Unknown option on line 1
Sep  8 05':0'1:28 router logger: Unknown option on line 2
Sep  8 05':0'1:28 router logger: Unknown option on line 3
Sep  8 05':0'1:28 router logger: Unknown option on line 4
Sep  8 05':0'1:28 router kernel: [eagle-usb] ioctl EU_IO_DSP received
Sep  8 05':0'1:28 router kernel: [eagle-usb] Loading DSP code to device...
Sep  8 05':0'1:28 router kernel: [eagle-usb] DSP code successfully loaded to device
Sep  8 05':0'1:28 router logger: Options successfully sent to driver.
Sep  8 05':0'1:28 router logger: Using DSP code for ISDN line
Sep  8 05':0'1:28 router logger: DSP code successfully loaded.
Sep  8 05':0'1:28 router logger: /etc/rc.d/rc.hotplug start (exiting script)
Sep  8 05':0'1:29 router sshd[998]: Server listening on 0.0.0.0 port 22.
Sep  8 05':0'1:40 router kernel: [eagle-usb] Modem operational !!
Sep  8 05':0'1:40 router kernel: [eagle-usb]  Ethernet device eth1 created.
Sep  8 05':0'1:40 router kernel: NET4: AppleTalk 0.18a for Linux NET4.0
Sep  8 05':0'1:40 router atalkd[1039]: [main.c:1090]: I:ATalkDaemon: restart (1.6.4)
Sep  8 05':0'1:41 router atalkd[1039]: [zip.c:910]: I:ATalkDaemon: zip_getnetinfo for eth0
Sep  8 05':0'1:42 router logger: /etc/rc.d/rc.inet1:  /sbin/iwconfig eth1 nick router
Sep  8 05':0'1:42 router logger: /etc/rc.d/rc.inet1:  /sbin/iwconfig eth1 essid any
Sep  8 05':0'1:51 router atalkd[1039]: [zip.c:910]: I:ATalkDaemon: zip_getnetinfo for eth0
Sep  8 05':0'2':0'1 router atalkd[1039]: [zip.c:910]: I:ATalkDaemon: zip_getnetinfo for eth0
Sep  8 05':0'2:11 router atalkd[1039]: [main.c:278]: I:ATalkDaemon: config for no router
Sep  8 05':0'2:12 router atalkd[1039]: [main.c:659]: I:ATalkDaemon: ready 0/0/0
Sep  8 05':0'2:24 router papd[1073]: [main.c:278]: I:PAPDaemon: restart (1.6.4)
Sep  8 05':0'2:24 router apmd[1083]: Version 3.0.2 (APM BIOS 1.2, Linux driver 1.16)
Sep  8 05':0'2:24 router apmd[1083]: Charge: * * * (-1% unknown)
Sep  8 05':0'2:30 router afpd[1075]: [afp_config.c:249]: I:AFPDaemon: router:AFPServer@* started on 65280.53:128 (1.6.4)
Sep  8 05':0'2:30 router afpd[1075]: [afp_config.c:311]: I:AFPDaemon: ASIP started on 192.168.1.254:548(2) (1.6.4)
Sep  8 05':0'2:30 router afpd[1075]: [auth.c:560]: I:AFPDaemon: uam: uams_guest.so loaded
Sep  8 05':0'2:30 router afpd[1075]: [auth.c:560]: I:AFPDaemon: uam: uams_clrtxt.so loaded
Sep  8 05':0'2:31 router afpd[1075]: [auth.c:560]: I:AFPDaemon: uam: uams_dhx.so loaded
Sep  8 05':0'2:31 router afpd[1075]: [auth.c:127]: I:AFPDaemon: uam: "DHCAST128" available
Sep  8 05':0'2:31 router afpd[1075]: [auth.c:127]: I:AFPDaemon: uam: "Cleartxt Passwrd" available
Sep  8 05':0'2:31 router afpd[1075]: [auth.c:127]: I:AFPDaemon: uam: "No User Authent" available
Sep  8 05':0'3:21 router kernel: [eagle-usb] ioctl EU_IO_OPTIONS received
Sep  8 05':0'3:21 router kernel: [eagle-usb] ioctl EU_IO_DSP received
Sep  8 05':0'3:21 router kernel: [eagle-usb] Loading DSP code to device...
Sep  8 05':0'3:21 router kernel: [eagle-usb] DSP code successfully loaded to device
Sep  8 05':0'3:42 router kernel: [eagle-usb] Modem operational !!
Sep  8 05':0'4:19 router kernel: CSLIP: code copyright 1989 Regents of the University of California
Sep  8 05':0'4:19 router kernel: PPP generic driver version 2.4.2
Sep  8 05':0'4:19 router pppd[1218]: pppd 2.4.2 started by root, uid 0
Sep  8 05':0'4:19 router pppd[1218]: Using interface ppp0
Sep  8 05':0'4:19 router pppd[1218]: Connect: ppp0 <--> /dev/pts/0
Sep  8 05':0'4:50 router pppd[1218]: Connection terminated.
Sep  8 05':0'4:54 router pppd[1218]: Exit.

И това е от ethereal:
No.     Time        Source                Destination           Protocol Info
      1 0.000000    ElconSys_ff:26':0'4     Broadcast             PPPoED   Active Discovery Initiation (PADI)

Frame 1 (32 bytes on wire, 32 bytes captured)
Ethernet II, Src: 00':0'7:23:ff:26':0'4, Dst: ff:ff:ff:ff:ff:ff
PPP-over-Ethernet Discovery
PPPoE Tags

No.     Time        Source                Destination           Protocol Info
      2 4.992719    ElconSys_ff:26':0'4     Broadcast             PPPoED   Active Discovery Initiation (PADI)

Frame 2 (32 bytes on wire, 32 bytes captured)
Ethernet II, Src: 00':0'7:23:ff:26':0'4, Dst: ff:ff:ff:ff:ff:ff
PPP-over-Ethernet Discovery
PPPoE Tags

No.     Time        Source                Destination           Protocol Info
      3 14.992714   ElconSys_ff:26':0'4     Broadcast             PPPoED   Active Discovery Initiation (PADI)

Frame 3 (32 bytes on wire, 32 bytes captured)
Ethernet II, Src: 00':0'7:23:ff:26':0'4, Dst: ff:ff:ff:ff:ff:ff
PPP-over-Ethernet Discovery
PPPoE Tags


Модема според мен е инициализиран. Светя
Активен

Donislav

  • Участници
  • ***
  • Публикации: 4
    • Профил
ELCON ADSL HELP!
« Отговор #6 -: Sep 08, 2004, 22:06 »
Sorry
Та значи на модема му светят двата диода Power i ADSL дори и DATA мига когато пусна adls-start или pppoe -I eth1 -A

Ще бъда мн благодарен ако можеш да ми дадеш някакви насоки. Вече доста време се тормозя с това.
Активен

Подобни теми
Заглавие Започната от Отговора Прегледи Последна публикация
ADSL от БТК
Хардуерни и софтуерни проблеми
kris_p 16 3911 Последна публикация Jun 17, 2004, 21:20
от Kasho
BTK ADSL
Настройка на хардуер
kris_p 1 1590 Последна публикация Jun 17, 2004, 21:10
от kris_p
ADSL
Идеи и мнения
jivko_66 7 1978 Последна публикация Nov 27, 2004, 16:00
от
adsl->nat->my box
Идеи и мнения
kumara 2 1256 Последна публикация Jan 10, 2005, 16:02
от ntenev
БТК ADSL и Линукс рутер
Настройка на хардуер
Desertleo 14 5898 Последна публикация Jul 06, 2005, 08:14
от