Изпечатай

[plamen_t]

Как мога да си сменя резолюцията на Slackware 10?
Искам от 1024х768 да ми стане 800х600. Пробвах от Control Centre-> Peripherals-> Display ,но там показва само че мога да бъда на 1024х768. Редактирах и xorg.conf и като рестартирах не ми излезна нищо на монитора. Може да не съм го редактирал правилно.

Ето и какво съдържа xorg.conf настройките на монитора и т.н.:

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

    Identifier  "My Monitor"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    HorizSync   60.0 - 100.0

#    HorizSync   30-64         # multisync
#    HorizSync   31.5, 35.2    # multiple fixed sync frequencies
#    HorizSync   15-25, 30-50  # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    VertRefresh 40-90

EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

Section "Device"
    Identifier  "VESA Framebuffer"
    Driver      "vesa"
    #VideoRam    4096
    # Insert Clocks lines here if appropriate
EndSection

# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present.  Each describes
# the configuration of a single screen.  A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
    Identifier  "Screen 1"
    Device      "VESA Framebuffer"
    Monitor     "My Monitor"

# If your card can handle it, a higher default color depth (like 24 or 32)
# is highly recommended.

#   DefaultDepth 8
#   DefaultDepth 16
   DefaultDepth 24
#   DefaultDepth 32

# "1024x768" is also a conservative usable default resolution.  If you
# have a better monitor, feel free to try resolutions such as
# "1152x864", "1280x1024", "1600x1200", and "1800x1400" (or whatever your
# card/monitor can produce)

    Subsection "Display"
        Depth       8
        Modes "640x480" "800x600" "1024x768"
    EndSubsection
    Subsection "Display"
        Depth       16
        Modes "640x480" "800x600" "1024x768"
    EndSubsection
    Subsection "Display"
        Depth       24
        Modes "640x480" "800x600" "1024x768"
    EndSubsection
    Subsection "Display"
        Depth       32
        Modes "640x480" "800x600" "1024x768"
    EndSubsection

EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present.  Each describes
# the way multiple screens are organised.  A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option.  In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
    Identifier  "Simple Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens.  The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen.  In this example, screen 2 is located to the
# right of screen 1.

    Screen "Screen 1"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used.  Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

    InputDevice "Mouse1" "CorePointer"
    InputDevice "Keyboard1" "CoreKeyboard"

EndSection

[sys7em]

Стойностите които те интересуват са ...
HorizSync   60.0 - 100.0
   VertRefresh 40-90


Погледни в мануала на монитора ...какви стойности трябва да въведеш ...

П.С. Не ползваш търсачката ... на този въпрос вече е отговаряно ... така че следващия път ползвай бутона търсене ... първо .. PEACE  '>  

[coldy]

Не съм на Linux в момента, но опитай в X да смениш резолюцията с Ctrl и бутона - или Ctrl Alt и бутона -

по този начин сменяш резолюциите описани в конфигурационния файл.