Изпечатай

[3v1]

при инсталация на Debian си сложих бозата да ми е в списък на лило , но след инсталация направо ми зарежда линукса. едитнах си lilo.conf в този вид:

Примерен код

# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)', # ---------------       `install-mbr(8)', `/usr/share/doc/lilo/', #                       and `/usr/share/doc/mbr/'. # +---------------------------------------------------------------+ # |                        !! Reminder !!                         | # |                                                               | # | Don't forget to run `lilo' after you make changes to this     | # | conffile, `/boot/bootmess.txt' (if you have created it), or   | # | install a new kernel.  The computer will most likely fail to  | # | boot if a kernel-image post-install script or you don't       | # | remember to run `lilo'.                                       | # |                                                               | # +---------------------------------------------------------------+ # Specifies the boot device.  This is where Lilo installs its boot # block.  It can be either a partition, or the raw device, in which # case it installs in the MBR, and will overwrite the current MBR. # boot=/dev/sda # Specifies the device that should be mounted as root. (`/') # root=/dev/sda2 # This option may be needed for some software RAID installs. # # raid-extra-boot=mbr-only # Enable map compaction: # Tries to merge read requests for adjacent sectors into a single # read request. This drastically reduces load time and keeps the # map smaller.  Using `compact' is especially recommended when # booting from a floppy disk.  It is disabled here by default # because it doesn't always work. # # compact # Installs the specified file as the new boot sector # You have the choice between: text, bmp, and menu # Look in lilo.conf(5) manpage for details # #install=menu # Specifies the location of the map file # map=/boot/map # You can set a password here, and uncomment the `restricted' lines # in the image definitions below to make it so that a password must # be typed to boot anything but a default configuration.  If a # command line is given, other than one specified by an `append' # statement in `lilo.conf', the password will be required, but a # standard default boot will not require one. # # This will, for instance, prevent anyone with access to the # console from booting with something like `Linux init=/bin/sh', # and thus becoming `root' without proper authorization. # # Note that if you really need this type of security, you will # likely also want to use `install-mbr' to reconfigure the MBR # program, as well as set up your BIOS to disallow booting from # removable disk or CD-ROM, then put a password on getting into the # BIOS configuration as well.  Please RTFM `install-mbr(8)'. # # password=tatercounter2000 # Specifies the number of deciseconds (0.1 seconds) LILO should # wait before booting the first image. # delay=20 # You can put a customized boot message up if you like.  If you use # `prompt', and this computer may need to reboot unattended, you # must specify a `timeout', or it will sit there forever waiting # for a keypress.  `single-key' goes with the `alias' lines in the # `image' configurations below.  eg: You can press `1' to boot # `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'. # # message=/boot/bootmess.txt #   prompt #   delay=10 #   timeout=10 # Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>) # # vga=ask # vga=9 # # Kernel command line options that apply to all installed images go # here.  See: The `boot-prompt-HOWTO' and `kernel-parameters.txt' in # the Linux kernel `Documentation' directory. # # append=""   # If you used a serial console to install Debian, this option should be # enabled by default. # serial= # # # image=/vmlinuz    label=Linux    read-only #   restricted #   alias=1    initrd=/initrd.img image=/vmlinuz.old    label=LinuxOLD    read-only    optional #   restricted #   alias=2    initrd=/initrd.img.old other=/dev/sda1    label=Windows1 #   restricted #   alias=2 # If you have another OS on this machine to boot, you can uncomment the # following lines, changing the device name on the `other' line to # where your other OS' partition is. # # other=/dev/hda4 #   label=HURD #   restricted #   alias=3 other=/dev/sda3    label=Windows #   restricted #   alias=2 other=/dev/sda1    label=Windows1 #   restricted #   alias=2

windows-a  ми е на /sda1 . някъкви идеи къде бъркам?
ето и изход от fdisk -l

Примерен код

Device Boot      Start         End      Blocks   Id  System /dev/sda1   *           1        2615    21004956    7  HPFS/NTFS /dev/sda2            2616        5282    21422677+  83  Linux /dev/sda3            5283       30140   199671885    b  W95 FAT32 /dev/sda4           30141       30401     2096482+  82  Linux swap / Solaris

[Gruntz]

Не съм сигурен, но:

пробвай да разкоментирш "# prompt", да стане само "prompt".

[3v1]

не стана. може ли проблема да е в това , че не съм го маунтнал този диск?

[carpo]

въпрос 1: пусна ли lilo след като редактира файла?
въпрос 2: може и да не съм видял правилно, ама няма ли да е по-добре ако няма секции със една и съща информация? (не съм потребител на LILO - аз ползвам GRUB GRUB download site)

Просто мойте 20 ст'инки...

Успех!
 '>

[3v1]

на първи въпрос , прочетох , че трябва да направя нещо такова , но не знам как. аз си инсталирах и grub

Примерен код

apt-get install grub grub-install /dev/sda3/

но ми зарежда през лило-то пак .  може би с тия 2-та реда става когато нямам никакъв лоадър.

[Gruntz]

Когато направиш промени в lilo.conf, трябва да изпълниш командата "lilo" като root, за да се презапише boot сектора. Чак след това промените ти в lilo.conf влизат в сила.

Успех.

[3v1]

не става

Примерен код

bash: lilo: command not found

[sak81]

Цитат (3v1 @ Ян. 24 2008,20:28)

не става Примерен код bash: lilo: command not found

с root ли изпълняваш командата?