Изпечатай

[Premiership]

Никак не ми трябва 3D...само 1024Х768@85 ми трябва...
А относно rpm-a дава някаква грешка в самото начало макар че пробвах с --force --nodeps (или нещо от рода)...Ще трябва да разуча това rpm2tgz..zmeYski а ти би ли постнал твоя XF86Config..

[zmeYski]

Нямаш проблеми, ето го и него:


Section "Module"

# This loads the DBE extension module.

    Load        "dbe"   # Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
    SubSection  "extmod"
      Option    "omit xfree86-dga"   # don't initialise the DGA extension
    EndSubSection

# This loads the font modules
    Load        "type1"
#    Load        "speedo"
    Load        "freetype"
#    Load        "xtt"

# This loads the GLX module
#    Load       "glx"
# This loads the DRI module
#    Load       "dri"

EndSection

# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.

    RgbPath "/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#
#

    FontPath   "/usr/X11R6/lib/X11/fonts/misc/"
    FontPath   "/usr/X11R6/lib/X11/fonts/TTF/"
    FontPath   "/usr/X11R6/lib/X11/fonts/Type1/"
    FontPath   "/usr/X11R6/lib/X11/fonts/75dpi/"
    FontPath   "/usr/X11R6/lib/X11/fonts/100dpi/"
    FontPath   "/usr/X11R6/lib/X11/fonts/local/"
    FontPath   "/usr/X11R6/lib/X11/fonts/cyrillic/"
    FontPath   "/usr/X11R6/lib/X11/fonts/artwiz-fonts/"
#    FontPath   "/usr/X11R6/lib/X11/fonts/Speedo/"
#    FontPath   "/usr/X11R6/lib/X11/fonts/TrueType/"
    FontPath   "/usr/X11R6/lib/X11/fonts/freefont/"
#  FontPath   "/usr/X11R6/lib/X11/fonts/CID/"

# The module search path.  The default path is shown here.

#    ModulePath "/usr/X11R6/lib/modules"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is
# received.  This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

#    Option "NoTrapSignals"

# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12).  This allows clients to receive these key
# events.

#    Option "DontVTSwitch"

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.

#    Option "DontZap"

# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences.  This allows clients to receive these key events.

#    Option "Dont Zoom"

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

#    Option "DisableVidModeExtension"

# Uncomment this to enable the use of a non-local xvidtune client.

#    Option "AllowNonLocalXvidtune"

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.

#    Option "DisableModInDev"

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

#    Option "AllowNonLocalModInDev"

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************

Section "InputDevice"

    Identifier "Keyboard1"
    Driver "kbd"

# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.

#    Option     "Protocol"      "Xqueue"

    Option "AutoRepeat" "500 30"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
#    Option "Xleds"      "1 2 3"

#    Option "LeftAlt"     "Meta"
#    Option "RightAlt"    "ModeShift"

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults).  For example, for a non-U.S.
# keyboard, you will probably want to use:
#    Option "XkbModel"    "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
#    Option "XkbModel"    "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#    Option "XkbLayout"   "de"
# or:
#    Option "XkbLayout"   "de"
#    Option "XkbVariant"  "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
#    Option "XkbOptions"  "ctrl:swapcaps"

# These are the default XKB settings for Xorg
#    Option "XkbRules"    "xorg"
#    Option "XkbModel"    "pc101"
#    Option "XkbLayout"   "us"
#    Option "XkbVariant"  ""
#    Option "XkbOptions"  ""

#    Option "XkbDisable"

    Option "XkbRules" "xorg"
    Option "XkbModel" "pc105"
    Option "XkbLayout" "de,bg"
    Option "XkbVariant" "nodeadkeys,phonetic"
    Option "XkbOptions"      "grp:alt_shift_toggle"

EndSection


# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************

Section "InputDevice"

# Identifier and driver

    Identifier "Mouse1"
    Driver "mouse"
    Option "Protocol"    "IMPS/2"
    Option "Device"      "/dev/psaux"
    Option "ZAxisMapping"  "4 5"


# Mouse-speed setting for PS/2 mouse.

#    Option "Resolution" "256"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

#    Option "Protocol" "Xqueue"

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

#    Option "BaudRate" "9600"
#    Option "SampleRate" "150"

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

#    Option "Emulate3Buttons"
#    Option "Emulate3Timeout"    "50"

# ChordMiddle is an option for some 3-button Logitech mice

#    Option "ChordMiddle"

EndSection

 **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

    Identifier  "dell"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    HorizSync   30-96

#    HorizSync 30-64         # multisync
#    HorizSync 31.5, 35.2    # multiple fixed sync frequencies
#    HorizSync 15-25, 30-50  # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    VertRefresh 48-120
    Option "DPMS"
      
EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
    Identifier "Standard VGA"
    VendorName "Unknown"
    BoardName "Unknown"

# The chipset line is optional in most cases.  It can be used to override
# the driver's chipset detection, and should not normally be specified.

#    Chipset "generic"

# The Driver line must be present.  When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module.  Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.

    Driver     "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for.  When this line isn't present, a device
# section can only match up with the primary video device.  For PCI
# devices a line like the following could be used.  This line should not
# normally be included unless there is more than one video device
# intalled.

#    BusID      "PCI:0:10"

#    VideoRam 256

#    Clocks 25.2 28.3

EndSection

# Device configured by xorgconfig:

Section "Device"
    Identifier  "radeon9600"
    Driver      "radeon"
    #VideoRam    131072
    # Insert Clocks lines here if appropriate
EndSection


# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present.  Each describes
# the configuration of a single screen.  A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
    Identifier  "Screen 1"
    Device      "radeon9600"
    Monitor     "dell"
    DefaultDepth 24

    Subsection "Display"
        Depth       8
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       16
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       24
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present.  Each describes
# the way multiple screens are organised.  A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option.  In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
    Identifier  "Simple Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens.  The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen.  In this example, screen 2 is located to the
# right of screen 1.

    Screen "Screen 1"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used.  Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

    InputDevice "Mouse1" "CorePointer"
    InputDevice "Keyboard1" "CoreKeyboard"

EndSection

# Section "DRI"
#    Mode 0666
# EndSection

RPM-a е нормално да дава грешки правен е за различна от твоята дистрибуция все пак  '>

[Premiership]

root@Orion:/lib/modules/fglrx# ls
build_mod/             fglrx.2.4.20-28.8.o        fglrx.2.4.20-28.9.o        fglrx.2.4.20-8.o        make_install.sh
fglrx.2.4.18-17.7.x.o  fglrx.2.4.20-28.8bigmem.o  fglrx.2.4.20-28.9bigmem.o  fglrx.2.4.20-8bigmem.o
fglrx.2.4.18-17.8.0.o  fglrx.2.4.20-28.8smp.o     fglrx.2.4.20-28.9smp.o     fglrx.2.4.20-8smp.o

root@Orion:/lib/modules/fglrx# ls build_mod/
2.6.x/  agp3.c         agpgart.h     firegl_public.c  i7505-agp.c         libfglrx_ip.a.GCC3  nvidia-agp.c
agp.h   agp_backend.h  agpgart_be.c  firegl_public.h  libfglrx_ip.a.GCC2  make.sh

root@Orion:/lib/modules/fglrx# ls build_mod/2.6.x/
Makefile

root@Orion:/lib/modules/fglrx# ls /usr/src/ATI
fglrx_panel_sources.tgz  fglrx_sample_source.tgz

Tova e sled rpm2tgz, installpkg.Ottuk natatyk kakvo da pravq...Tezi .tgz v /use/src/ATI ne sym im dal installpkg...2.6.9 kernel
Predvaritelno blagodarq:)

[Premiership]

Pitaneto mi beshe porodeno ot fakta che vidqh samo 2.4xxxxx failove...(a az sym s 2.6.9).No sega vsichko trygna idealno 1024x768@85Hz -
Hilqdi blagodarnosti na vsichki '>